Summary of the content on the page No. 1
RX-V659
RX-V659_U_cv.fm Page 1 Wednesday, November 23, 2005 11:09 AM
U
RX-V659
AV Receiver
© 2006 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG
Summary of the content on the page No. 2
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 10 Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the CAUTION product and to protect it from overheating, and these RISK OF ELECTRIC SHOCK openings must not be blocked or covered. The openings DO NOT OPEN should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS d) If the product does not operate normally by following 24 Outdoor Antenna Grounding – If an outside antenna or the operating instructions. Adjust only those controls cable system is connected to the product, be sure the antenna that are covered by the operating instructions as an or cable system is grounded so as to provide some improper adjustment of other controls may result in protection against voltage surges and built-up static charges. damage and will of
Summary of the content on the page No. 4
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 To assure the finest performance, please read this manual 15 When not planning to use this unit for long periods of time carefully. Keep it in a safe place for future reference. (i.e. vacation), disconnect the AC power plug from the wall outlet. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, 16 Install this unit near th
Summary of the content on the page No. 5
BASIC SOUND FIELD ADDITIONAL ADVANCED OPERATION PROGRAMS INFORMATION INTRODUCTION PREPARATION OPERATION CONTENTS ENJOYING SURROUND SOUND.....................48 INTRODUCTION Enjoying multi-channel sources in surround ........... 48 Enjoying 2-channel sources in surround.................. 49 FEATURES............................................................. 2 Using Virtual CINEMA DSP .................................. 50 GETTING STARTED............................................ 3 RECORDING.
Summary of the content on the page No. 6
FEATURES FEATURES Built-in 7-channel power amplifier iPod controlling capability ◆ Minimum RMS output power ◆ DOCK terminal to connect a YAMAHA iPod universal dock (0.06% THD, 20 Hz to 20 kHz, 8 Ω) (such as YDS-10 sold separately), which supports iPod (Click Front: 100 W + 100 W and Wheel), iPod nano, and iPod mini Center: 100 W Other features Surround: 100 W + 100 W ◆ YPAO (YAMAHA Parametric Room Acoustic Optimizer) for Surround back: 100 W + 100 W automatic speaker setup Sound field program
Summary of the content on the page No. 7
INTRODUCTION GETTING STARTED GETTING STARTED Supplied accessories Check that you received all of the following parts. Remote control CODE SET TRANSMIT Batteries (2) AM loop antenna Optimizer microphone POWER POWER STANDBY POWER (AA, R6, UM-3) (except for U.K. model) TV AV MD SLEEP CD CD-R XM CBL MULTI CH IN DVD DTV TUNER PHONO V-AUX DVR VCR AMP SOURCE TV VOL TV CH VOLUME TV TV MUTE TV INPUT MUTE STEREO MUSIC ENTERTAIN MOVIE 1 2 3 4 STANDARD SELECT EXTD SUR. PURE DIRECT 5 6 7 8 SPEAKERS ENHANCER
Summary of the content on the page No. 8
CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS Front panel Note The XM Satellite Radio controlling functions in the following buttons (SEARCH MODE, CATEGORY, PRESET/TUNING/CH l / h, MEMORY, and DISPLAY) are only applicable to the U.S.A. model and are operational only when “XM” is selected as the input source. For details, see “XM Satellite Radio controls and functions” on page 60. 14 2 3 56 7890 A B VOLUME ZONE 2 ZONE ON/OFF CONTROL MASTER PRESET/TUNING FM/AM A/B/C/D/E l PRESET/TUNING/CH h ME
Summary of the content on the page No. 9
INTRODUCTION CONTROLS AND FUNCTIONS 8 MEMORY (MAN’L/AUTO FM) G FM/AM Stores a preset station in the memory. Hold down this Switches the reception band between FM and AM when button for more than 3 seconds to start automatic preset “TUNER” is selected as the input source (see page 52). tuning (see page 54). H PROGRAM selector 9 TUNING MODE (AUTO/MAN’L) Selects sound field programs or adjusts the bass/treble Switches between automatic tuning (the AUTO indicator balance in conjunction with TONE C
Summary of the content on the page No. 10
CONTROLS AND FUNCTIONS Remote control This section describes the function of each control on the remote control used to control this unit. To operate other components, see “REMOTE CONTROL FEATURES” on page 99. Notes The XM Satellite Radio controlling functions in the following buttons (XM, XM MEMORY, SRCH MODE, DISPLAY, cursor buttons u / d / j / i, numeric buttons and ENT.) are only applicable to the U.S.A. model and are operational only when “XM” is selected as the input source. For detai
Summary of the content on the page No. 11
INTRODUCTION CONTROLS AND FUNCTIONS 8 Cursor buttons u / d / j / i, ENTER G MUTE Select and adjust the sound field program parameters or Mutes the audio output. Press again to restore the audio the “SET MENU” parameters. output to the previous volume level (see page 40). 9 RETURN H STRAIGHT (EFFECT) Returns to the previous menu level when adjusting the Turns the sound field programs off or on. When the “SET MENU” parameters. “STRAIGHT” mode is selected, 2-channel or multi- channel input signal
Summary of the content on the page No. 12
CONTROLS AND FUNCTIONS ■ Controlling the TUNER functions ■ Using the remote control Set the component selector switch to SOURCE and then The remote control transmits a directional infrared ray. press TUNER to select “TUNER” as the input source. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. 4 Numeric buttons Use numbers 1 through 8 to select preset stations. (U.S.A. model) 7 BAND Switches the reception band between FM and AM VOLUME ON/OFF
Summary of the content on the page No. 13
INTRODUCTION CONTROLS AND FUNCTIONS Front panel display Note The XM indicator is only applicable to the U.S.A. model and the cursor on the left of the XM indicator lights up only when “XM” is selected as the input source. For details, see “Basic XM Satellite Radio operations” on page 62. 13 24568 7 9C 0AB D 96 pVCR pDVR pV-AUX pDTV/CBL pDVD pMD/CD-R pTUNER pCD pXM pPHONO t 24 VOLUME DOCK YPAO AUTO TUNED STEREO MEMORY MATRIX DISCRETE VIRTUAL SILENT CINEMA SP dB ENHANCER STANDARD A B ZONE2 NIGHT
Summary of the content on the page No. 14
CONTROLS AND FUNCTIONS F STANDARD indicator Q LFE indicator Lights up when the “SUR. STANDARD” or “SUR. Lights up when the input signal contains the LFE signal. ENHANCED” program is selected (see page 49). R Radio Data System indicators G SP A B indicators (U.K. and Europe models only) Light up according to the set of front speakers selected. Lights up when the Radio Data System data is being received. H Headphones indicator EON Lights up when headphones are connected (see page 40). Lights up w
Summary of the content on the page No. 15
INTRODUCTION CONTROLS AND FUNCTIONS Rear panel 1 2 3 4 5 6 78 9 0 TUNER 75Ω UNBAL. AM FM GND ANT ANT AUDIO AUDIO DOCK COMPONENT VIDEO PHONO Y PB PR GND XM DVD REMOTE CONTROL OUT +12V IN OUT VIDEO PRESENCE/ZONE2 15mA MAX. DTV/ DIGITAL OUTPUT CBL MD/CD-R DVD PRE OUT CD FRONT SURROUND CENTER SURROUND BACK SINGLE DVR IN DTV/ OPTICAL (PLAY) CBL MD/ CD-R OUT IN MD/CD-R (REC) DVR MONITOR OUT SUBWOOFER SPEAKERS DVD FRONT OUT A SURROUND DTV/CBL IN SURROUND VCR SURROUND BACK OUT CD B DVD FRONT CENTER SUR
Summary of the content on the page No. 16
CONNECTIONS CONNECTIONS Placing speakers * The speaker layout below shows the standard ITU-R Front left and right speakers (FL and FR) speaker setting. You can use it to enjoy CINEMA DSP and The front speakers are used for the main source sound plus multi-channel audio sources. effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each * ITU-R is the radio communication sector of the ITU speaker from each side of the video monitor should
Summary of the content on the page No. 17
PREPARATION CONNECTIONS Connecting speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. CAUTION Before connecting the speakers, make sure that this unit is turned off (see page 31). Do not let the bare speaker wires touch each other or do not let them touch any met
Summary of the content on the page No. 18
CONNECTIONS FRONT terminals Speaker layout Connect one or two front speaker systems (6, 7) to these 2 terminals. If you use only one front speaker system, connect it to the FRONT A or B terminal. 3 6 1 CENTER terminals 4 7 Connect a center speaker (8) to these terminals. 8 SURROUND terminals 9 Connect surround speakers (4, 5) to these terminals. 5 10 SURROUND BACK terminals Connect a surround back speakers (9, 10) to these terminals. PRESENCE/ZONE2 terminals Connect presence speakers (2, 3) t
Summary of the content on the page No. 19
PREPARATION CONNECTIONS ■ Connecting the speaker cable ■ Connecting to the PRESENCE/ZONE2 speaker terminals Connect presence speakers to these terminals. 1 Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker y cable and then twist the exposed wires of the You can also use these terminals to connect the Zone 2 speakers (see page 104). cable together to prevent short circuits. 1 Open the tab. 10 mm (0.4 in) 2 Loosen the knob. 2 Insert one bare wire into the hole on t
Summary of the content on the page No. 20
CONNECTIONS ■ Connecting the banana plug (except U.K., Europe and Asia models) The banana plug is a single-pole electrical connector widely used to terminate speaker cables. Banana plug y You can also use the banana plug with the PRESENCE/ZONE2 speaker terminals. Open the tab and then insert one banana plug into the hole on the side of each terminal. Do not close the tab after connecting the banana plug. 1 Tighten the knob. 2 Insert the banana plug connector into the end of the correspondin
