Summary of the content on the page No. 1
EF16-35mm f/4L IS USM
ENG
Instructions
C OP Y
Summary of the content on the page No. 2
Thank you for purchasing a Canon product. Canon’s EF16-35mm f/4L IS USM is a high- 4. Ultrasonic motor (USM) for fast, quiet autofocus. performance ultra-wide angle zoom lens, for use 5. Manual focusing is available after the subject with EOS cameras. The lens is installed with an comes into focus in autofocus mode (ONE Image Stabilizer. SHOT AF). 6. Circular aperture for producing beautiful ● ● “IS” stands for Image Stabilizer. softfocus images. ● ● “USM” stands for Ultrasonic Motor. 7. Tigh
Summary of the content on the page No. 3
Safety Precautions Handling Cautions Safety Precautions ● ●If the lens is taken from a cold environment into a ● ●Do not look at the sun or a bright light source warm one, condensation may develop on the lens through the lens or camera. Doing so could result in surface and internal parts. To prevent condensation loss of vision. Looking at the sun directly through the in this case, first put the lens into an airtight plastic bag lens is especially hazardous. before taking it from a cold
Summary of the content on the page No. 4
Safety Precautions This device complies with Part 15 of the FCC Rules. CAN ICES-3 (B) / NMB-3 (B) Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be re
Summary of the content on the page No. 5
Nomenclature Focus mode switch (→ 6) Distance scale (→ 7) Hood mount (→ 10) Zoom ring (→ 6) Rubber ring (→ 5) Filter Mounting Thread (→ 11) Contacts (→ 5) Focusing ring (→ 6) Lens mount index (→ 5) Image stabilizer switch (→ 8) ● ● F or detailed information, reference page numbers are provided in parentheses ( → **). ENG-4 C OP Y
Summary of the content on the page No. 6
1. Mounting and Detaching the Lens See your camera’s instructions for details on The lens mount has a rubber ring for enhanced mounting and detaching the lens. dust- and water-resistance. The rubber ring may cause slight abrasions around the camera’s lens mount, but this will not cause any problems. If the rubber ring becomes worn, it is replaceable by a Canon Service Center at cost. ● ● After detaching the lens, place the lens with the rear end up to prevent the lens surface and contact
Summary of the content on the page No. 7
2. Setting the Focus Mode 3. Zooming To shoot in autofocus (AF) mode, set the focus To zoom, rotate the zoom ring. mode switch to AF. Be sure to finish zooming before focusing. Zooming To shoot in manual focus (MF) mode, set the after focusing can affect the focus. focus mode switch to MF, and focus by turning the focusing ring. The focusing ring always works, regardless of the focus mode. After autofocusing in ONE SHOT AF mode, focus manually by pressing the shutter button halfway and
Summary of the content on the page No. 8
4. Infinity Compensation 5. Infrared Index Mark Infinity compensation mark The infrared index corrects the focus setting Distance index when using monochrome infrared film. Focus on the subject manually, then adjust the distance To compensate for shifting of the infinity focus setting by moving the focusing ring to the point that results from changes in temperature. corresponding infrared index mark. The infinity position at normal temperature is the point at which the vertical line of
Summary of the content on the page No. 9
6. Image Stabilizer You can use the image stabilizer in AF or MF mode. This function provides optimal image stabilization depending on shooting conditions (such as shooting still subjects and following shots). ON OFF The image stabilizer in this lens is 1 Set the STABILIZER 2 When you press the effective for hand-held shots under the switch to ON. shutter button halfway, the following conditions. Image Stabilizer will start ● ● If you are not going to use the ● ●In semi-darkened areas su
Summary of the content on the page No. 10
Image Stabilizer ● ● The Image Stabilizer cannot compensate for a ● ● When shooting a still subject, it compensates for blurred shot caused by a subject that moved. camera shake in all directions. ● ● Set the STABILIZER switch to OFF when you ● ● It compensates for vertical camera shake during are taking pictures using the Bulb setting (long following shots in a horizontal direction, and exposures). If the STABILIZER switch is set to compensates for horizontal camera shake during ON, the ima
Summary of the content on the page No. 11
7. Hood The EW-82 hood cuts out unwanted light and protects the front of the lens from rain, snow, and dust. Button ●Attaching ●Removing To attach the hood, align the hood’s attachment To remove the hood, hold down the button on position mark with the red dot on the front of the the side and turn the hood in the direction of the lens, then turn the hood as shown by the arrow arrow until the position mark on the hood aligns until the lens’ red dot is aligned with the hood’s with the red dot.
Summary of the content on the page No. 12
8. Filters 10. Extension Tubes (Sold separately) (Sold separately) You can attach filters to the filter mounting You can attach extension tube EF12 II or EF25 thread on the front of the lens. II for magnified shots. The shooting distance and magnification are shown below. ● ● To ensure dust- and water-resistant performance, Focusing Distance Range (mm) Magnification (×) attach a Canon PROTECT filter (77mm). ● ● Only one filter may be attached. Close distance Long distance Close distance Lo
Summary of the content on the page No. 13
Specifications Focal Length/Aperture 16-35mm f/4 Lens Construction 12 groups, 16 elements Minimum Aperture f/22 Angle of View Diagonal: 108° 10′ – 63°, Vertical: 74° 10′ – 38°, Horizontal: 98° – 54° Min. Focusing Distance 0.28 m/0.92 ft. Max. Magnification 0.23x (at 35mm) Approx. 222 x 343 – 105 x 157 mm/ Field of View 8.74 x 13.50 – 4.13 x 6.18 inch (at 0.28 m/0.92 ft.) Filter Diameter 77 mm/3.03 inch Max. Diameter and Length 82.6 x 112.8 mm/3.25 x 4.44 inch Weight Approx. 615 g/21.7 oz. Hood E
Summary of the content on the page No. 14
CT1-8597-000 0414Ni © CANON INC. 2014 C OP Y
