Summary of the content on the page No. 1
RX-V492RDS
RX-V392RDS
Natural Sound AV Receiver
Récepteur audiovisuel “Son Naturel”
Natural Sound AV-Receiver
Natural Sound AV-receiver
Sintonizzatore AV a suono naturale
Receptor AV de Sonido Natural
Natural Sound AV Ontvanger
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Summary of the content on the page No. 2
l SUPPLIED ACCESSORIES After unpacking, check that the following parts are included. l ACCESSOIRES FOURNIS Après le déballage, vérifier que les pièces suivantes sont incluses. l MITGELIEFERTE ZUBEHÖRTEILE Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. l MEDFÖLJANDE TILLBEHÖR Kontrollera efter det apparaten packats upp att följande delar finns med. l ACCESSORI IN DOTAZIONE Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio. l ACCESORIOS
Summary of the content on the page No. 3
English Thank you for selecting this YAMAHA AV receiver. FEATURES l l 5 Speaker Configuration Automatic Input Balance Control for Dolby Pro Logic Surround RX-V492RDS l Main: 65W + 65W (8Ω) RMS Output Test Tone Generator for Easier Speaker Power, 0.04% THD, 20–20,000 Hz Balance Adjustment Center: 65W (8Ω) RMS Output l 3 Center Channel Modes Power, 0.09% THD, 1 kHz (NORMAL/WIDE/PHANTOM) Rear: 20W + 20W (8Ω) RMS Output l Multi-Functions for RDS Broadcast Power, 0.7% THD, 1 kHz Reception RX-V392RD
Summary of the content on the page No. 4
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual For U.K. customers carefully. Keep it in a safe place for future reference. If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an 2. Install this unit in a cool, dry, clean place – away from appropriate 3 pin plug fitted. For details, refer to the windows, heat sources, sources of excessive vibration, instructions descri
Summary of the content on the page No. 5
English 30° NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range RX-V492RDS RX-V392RDS 20 l6 l2 20 l6 l2 28 8 28 8 40 4 40 4 2 60 2 60 2 0 0 –dB –dB 1 Remote control sensor 3 Within approximately 6 m (19.7 feet) Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes l Use only AA, R6, UM-3 batteries for replacement. l Be sur
Summary of the content on the page No. 6
PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments –
Summary of the content on the page No. 7
English SPEAKER SETUP SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration” shown below.) The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are
Summary of the content on the page No. 8
CONNECTIONS Never plug in this unit and other components until all connections are completed. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily
Summary of the content on the page No. 9
English RX-V392RDS Turntable Monitor TV Video cassette recorder 2 (Europe model) * IMPEDANCE SELECTOR REAR 6ΩMIN./SPEAKER OUTPUT CENTER SINGLE:6ΩMIN./SPEAKER GND VIDEO SIGNAL DUAL:3ΩMIN./SPEAKER MAIN A OR B:4ΩMIN./SPEAKER 75Ω A B:8ΩMIN./SPEAKER CENTER REAR UNBAL. MONITOR OUT VIDEO IN VCROUT REAR 8ΩMIN./SPEAKER CENTER SINGLE:8ΩMIN./SPEAKER DUAL:4ΩMIN./SPEAKER FM MAIN A OR B:8ΩMIN./SPEAKER A B:I6ΩMIN./SPEAKER ANT CENTER 1 CD SUB DUAL WOOFER GND SINGLE * MAINS AM AN
Summary of the content on the page No. 10
CONNECTING SPEAKERS Subwoofer system Rear speaker Rear speaker Left Right Center speaker (Europe model) IMPEDANCE SELECTOR REAR 6ΩMIN./SPEAKER OUTPUT CENTER SINGLE:6ΩMIN./SPEAKER DUAL:3ΩMIN./SPEAKER MAIN A OR B:4ΩMIN./SPEAKER CENTER A B:8ΩMIN./SPEAKER REAR REAR 8ΩMIN./SPEAKER CENTER SINGLE:8ΩMIN./SPEAKER DUAL:4ΩMIN./SPEAKER A OR B:8ΩMIN./SPEAKER MAIN A B:I6ΩMIN./SPEAKER CENTER CD SUB DUAL WOOFER SINGLE Main speakers B A Right Left B Right MAIN Left CAUTION SEE
Summary of the content on the page No. 11
English How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This
Summary of the content on the page No. 12
OUTPUT terminals (for driving speakers with external amplifiers) CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. OUTPUT However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to CENTER this terminal. SUBWOOFER OUTPUT terminal This terminal is for connecting with the input terminal of an SUB amplifier for driving a subwoofer.
Summary of the content on the page No. 13
English ANTENNA CONNECTIONS l Each antenna should be connected to the designated terminals correctly, referring to the following diagram. l Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Outdoor AM ante
Summary of the content on the page No. 14
CONTROLS AND THEIR FUNCTIONS FRONT PANEL RX-V492RDS 1 23 4 5 6 78 CONCERT MONO CINEMA DSP PRO LOGIC ENHANCED VIDEO MOVIE STADIUM NATURAL SOUND AV RECEIVER RX–V492RDS ROCK CONCERT DISCO CONCERT HALL EFFECT VOLUME l6 20 l2 VCR TV/DBS DVD/LD 28 8 POWER TAPE (MD) 40 4 MONITOR 60 2 TUNER PHONO CD A/B/C/D/E 1 2 3 4 5 6 7 8 0 –dB BASS TREBLE BALANCE DELAY/ CENTER PHONES SPEAKERS RDS MODE/FREQ EON FM/AM DOWN TUNING UP CENTER/REAR MODE 0 0 0 l l l l l l A B 2 2 2 2 2 2 TUNING 3 3 3 3 3 3 PTY SEEK M
Summary of the content on the page No. 15
English 1 POWER switch 0 SPEAKERS switches Press this switch to switch the power on. Press it again to Set the switch A or B (or both A and B) for the main speaker switch the power off. system (connected to this unit) you will use to the ON position. Set the switch for the main speaker system you will not use to 2 Standby mode indicator the OFF position. While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the standby mode. In A A/B/C/D/E button t
Summary of the content on the page No. 16
J MEMORY (MAN’L/AUTO FM) button N DELAY/CENTER/REAR and TIME/LEVEL +/– buttons When this button is pressed, the MEMORY indicator flashes for RX-V492RDS only about 5 seconds. During this period, select a desired preset Adjust the delay time (DELAY), the center channel output level station number by pressing the corresponding preset station (CENTER) and the rear channel output level (REAR). number selector button to enter the displayed station into the Select the item which you want to adjust by
Summary of the content on the page No. 17
English DISPLAY PANEL 123 4 56 PRESET SLEEP STEREO NORM ms dB WIDE kHz PHANTOM MHz 0 20 l00 EFFECT OFF DISCO PRO LOGIC CONCERT MONO ROCK CONCERT MEMORY AUTO PTY HOLD NEWS INFO TAPE MON ENHANCED VIDEO MOVIE STADIUM CONCERT HALL PS PTY RT CT EON AFFAIRS SPORT D 78 9 0B A C 1 Multi-information display 9 RDS mode indicators Displays various information, for example station frequency, The name(s) of RDS mode(s) employed by the currently preset station number and name of selected input source. receive
Summary of the content on the page No. 18
REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. RX-V392RDS RX-V492RDS 9 9 TIME/ DELAY/CENTER –+ LEVEL /REAR TEST EFFECT –+ DELAY TIME TEST EFFECT 1 1 8 8 ON/OFF ON/OFF PROGRAM PROLO
Summary of the content on the page No. 19
English For Control of This Unit For Other Component Control Identify the remote control transmitter keys with your 1 DELAY/CENTER/REAR and TIME/LEVEL +/– keys component’s keys. If these keys are identical, their functions RX-V492RDS only will be the same. On each key function, refer to the Adjust the delay time (DELAY), the center channel output level corresponding instruction on your component’s manual. (CENTER) and the rear channel output level (REAR). Select the item which you want to adju
Summary of the content on the page No. 20
SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder. RX-V492RDS RX-V392RDS 1 2 5 5 TIME/ DELAY/CENTER –+ LEVEL TEST EFFECT /REAR –
