Summary of the content on the page No. 1
PRESS PRESS T TAB AB WI WITH TH
TWEEKER TWEEKER T TO O RE REMO MOV VE E
12 3
AB
DISPLAY A B C D E DIGITAL MLS POWER
RS-232/IR COMM LINK I/O RS-232 12V
Contents
MLC 104 IP Plus Series • Setup Guide
MLC 104 IP Plus Series • Setup Guide 1
®
The Extron MLC 104 IP Plus Series MediaLink Controller integrates Ethernet connection into AV systems to allow users
to remotely control, monitor, and troubleshoot AV equipment, including display devices and switchers. It includes an
embed
Summary of the content on the page No. 2
MLC 104 IP Plus Series • Setup Guide (Continued) Cabling and Features Attach cables using the following wiring diagrams as a guide. Full details are available in the MLC 104 IP Plus Series User Guide. CAUTION: Installation and service must be performed by authorized personnel only. Control — Projector or Display Projector or Unidirectional Display RS-232 or IR (-) (-) IR RS-232 Port Ground ( ) Ground ( ) Ground ( ) IR Output Signal Projector (+) Receive (Rx) Receive (Rx) (+) or Display T
Summary of the content on the page No. 3
PRESS PRESS T TAB AB WI WITH TH TWEEKER TWEEKER T TO O RE REMO MOV VE E 12 1 2 3 3 A AB B DISPL DISPL DISPLAY AY AY A B C D ABCDE A B C D E E DIGI DIGI DIGITA TA TAL L L ML ML MLS S S POWE POWE POWER R R R RS-232/IR S-232/IR CO COMM LIN MM LINK K I/O I/O RS-232 RS-232 12V 12V Control — MLS Switcher (MLS RS-232 Port) Power Ground 12 VDC MLC/IR (ridged) (smooth) AB C Rear Panel Power Input MLC/IR port • Connect to 12 VDC, 1 A power supply. on MLS Switcher • Check
Summary of the content on the page No. 4
MLC 104 IP Plus Series • Setup Guide (Continued) Control — Serial (Config) DISPLAY ON OFF VCR 1 2 DVD VOLUME Config Serial (RS-232) Port PC 3 This port supports bidirectional RS-232 (-5 - +5 VDC) communication. CONFIG Protocol: 4 • 38400 baud • 8 data bits • 1 stop bit • no parity • no flow control Front panel Config port: • RS-232 only (Tx, Rx, ground) MLC 104 IP PLUS MLC104 IP Plus Front Panel 6 feet (1.8 m) Part #70-335-01 1 NOTES: 6 • Use the front panel Config port only for sending basic
Summary of the content on the page No. 5
Configuration 1. Download and install the latest versions of the following: z Global Configurator software — for setting up the MLC and creating a single system configuration file z Device driver package — for use with GC, to make control of other devices possible All are avail able from www.extron.com or on the included Extron Software Products Disc. 2. Obtain IP address and subnet mask information for the MLC from the network administrator. 3. Cable devices to the MLC (see”Cabling and Features
Summary of the content on the page No. 6
MLC 104 IP Plus Series • Setup Guide (Continued) Mounting Attach cables using the preceding pages Optional mounting kits Part number as a guide, then securely mount the SMB 102 Two-gang Surface Mount Box (black) 60-640-02 MLC and other devices into the wall or furniture. Optional mounting kits SMB 104 Four-gang Surface Mount Box (black) 60-642-02 (see part numbers at right) are MLM 104 6GWP Six-Gang Wall Mounting Kit (black) 70-355-02 available for use with the MLC. Read the instructions
