Summary of the content on the page No. 1
USER MANUAL
i6 AW & i6T AW
Summary of the content on the page No. 2
CONTENTS 15. Declaration of Conformity Warranty 14. i6 Recommended Service Parts & Accessories 13. Troubleshooting Guide 12. Technical Specifications 11. Performance Data 10. Hardware 9. Dimensions 8. Equalisation 7. Power Selection 6. Amplification & Power Handling 5. Polarity Checking 4. Connectors/Cabling 3. Unpacking 2. Introduction 1.
Summary of the content on the page No. 3
1. Introduction W (All Weather) is an ultra compact loudspeaker system capable of delivering high sound W offers outstanding durability and resistance to scuffs and knocks. Able to deliver consistent performance under a wide W will Utilisation of the point source Dual Concentric loudspeaker allows the i6 AW to be mounted on a wall or ceiling in either horizontal or vertical orientations without affecting its performance. A range of hardware options ensures simple and effective W). W comprises on
Summary of the content on the page No. 4
CABLE RUN C.S.A. OF EACH CABLE % POWER LOSS % POWER LOSS (m) CONDUCTOR (mm) RESISTANCE Ω Ω INTO 8Ω Ω LOAD INTO 4Ω Ω LOAD 10 2.5 0.14 1.7 3.5 4.0 0.09 1.1 2.2 6.0 0.06 0.73 1.5 25 2.5 0.35 4.3 8.6 4.0 0.22 2.7 5.4 6.0 0.14 1.8 3.6 50 2.5 0.69 8.6 17.0 4.0 0.43 5.4 11.0 6.0 0.29 3.6 7.2 100 2.5 1.38 17.0 35.0 4.0 0.86 11.0 22.0 6.0 0.58 7.2 14.0 4. Polarity Checking It is most important to check the polarity of the wiring. A simple method of doing this terminal also be noted that different amplif
Summary of the content on the page No. 5
6. Power Selection (i6T AW) Determine the maximum power in watts needed at each speaker location. The i6 AW the metal plate at rear of the loudspeaker. primaries should be connected in parallel to the output of this amplifier. If for example, When calculating amplifier wattage requirements for a system, it is recommended that 7. Equalisation acoustic environments. loudspeaker is a point source, phase coherent 8. Dimensions design and violent equalisation will be detrimental to the overall sound
Summary of the content on the page No. 6
9. Hardware W can be wall or ceiling mounted using the MB6 (optional) bracket ( fig 1.) fig1.& 2 ). After fixing the bracket to the wall or ceiling remove the plastic plugs from the top and bottom of bracket ( fig1.& 2. for other bracketry. Fig 1. Fig 2. NOTE: The installation of this product must be carried out in conformity with local building codes and standards. If necessary consult your local safety standards officer before installing any product. Alternatively, check any laws or bylaws.Tan
Summary of the content on the page No. 7
10. Performance Data Impedance Anechoic Frequency Response, 1watt @ 1m
Summary of the content on the page No. 8
Hororizontal ___ Vertical 1k 4k 2k 8k 16k 500Hz ----
Summary of the content on the page No. 9
11. Technical Specifications Frequency response (1) +/- 3dB Recommended Amplifier Power Power Handling Sensitivity (1) 2.83 volt @ 1m Maximum SPL (3) Peak @ 1m Maximum SPL (3) With THP30 Transformer Peak @ 1m Transformer (i6T AW) s Impedance Nominal DI Averaged (PCQ) 7.41 @ 1kHz (ISO) 6.1 @ 2kHz (ISO) 6.3 @ 4kHz (ISO) 9.7 @ 8kHz (ISO) 9.6 @ 16kHz (ISO) 13.6 Q Averaged (PCQ) 7.74 @ 1kHz (ISO) 4.1 @ 2kHz (ISO) 4.3 @ 4kHz (ISO) 9.3 @ 8kHz (ISO) 9.1 @ 16kHz (ISO) 22.9 Driver Complement Crossover
Summary of the content on the page No. 10
12. Troubleshooting Guide Symptom Possible Cause Action No Output From Speakers Broken Speaker Cables(s) Amplifier amplifier are turned up. “signal” indicators on the amp). working, make sure signal is fed output is obtained from the loudspeakers(s) then the problem is with the amplifier loudspeaker. Intermittent Output Check the loudspeaker cabling connection can increase reduce the output, or make “cracking” noises which are If using multi-strand loudspeaker cable, be sure no strands of cable
Summary of the content on the page No. 11
13. I6 AW Service Parts & Accessories Part Number Description HF Diaphragm Kit Yoke Bracket 14. Warranty the date of manufacture subject to the absence of misuse, overload or accidental removed. Customer Services e ML5 4TF Fax: Our policy commits us to incorporating improvements to our products through continuous research and development. Please confirm current specifications for EASE™ ™ Data for Tannoy Professional products available on request. critical applications with your supplier. DO NO
Summary of the content on the page No. 12
Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other app
