Summary of the content on the page No. 1
User’s Manual
P/2 DA2 WM F, WM EC F,
P/2 DA2 D, and AAP models
Distribution Amplifiers
68-463-02 Rev. C
09 08
© 2008 Extron Electronics. All rights reserved.
Summary of the content on the page No. 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is Extron Electronics warrants this product against defects in materials and in the literature pr
Summary of the content on the page No. 3
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communicati
Summary of the content on the page No. 4
Table of Contents Chapter 1 • Introduction ......................................................... 1-1 About the P/2 DA2 WM F/EC F, AAP and D Models .................................................................................... 1-2 Features ...................................................................................... 1-2 Chapter 2 � Controls and Installation ........................... 2-1 Front and Rear Panels ................................................. 2-2 Front faceplat
Summary of the content on the page No. 5
Table of Contents, cont’d Templates ............................................................................... A-15 P/2 DA2 WM F mounting template ................................... A-15 P/2 DA2 WM/EC/D/AAP Series P/2 DA2 WM F AAP mounting template ........................... A-16 P/2 DA2 D mounting template .......................................... A-17 Chapter One 1 Introduction About the P/2 DA2 WM F/ EC F, AAP, and D Models Features All trademarks mentioned in this manual are the prop
Summary of the content on the page No. 6
Introduction About the P/2 DA2 WM F/EC F, AAP, and D P/2 DA2 WM/EC/D/AAP Series Models The P/2 DA2 WM F/F EC, AAP, and D models are one input, two output, high resolution VGA/XGA distribution amplifiers with audio. With a video bandwidth of 300 MHz, these distribution amplifiers are compatible with VGA, SVGA, VESA, XGA, and SXGA graphics cards, monitors, projectors, and LCD ® panels. The D model features Decora faceplates and trim. For audio, the P/2 DA2 WM F/EC F and D feature a 3.5 mm female
Summary of the content on the page No. 7
Controls and Installation Unity – output signal level is same as that of input with no added Front and Rear Panels peaking Front faceplate 50% – increases the output signal level and adds 50% of the maximum peaking to the signal N If the edges of the image seem to exceed their boundaries, or if thin lines and sharp edges look thick and fuzzy, try changing the level/peak setting. AUTO POWER 1 2 1 P/2 DA2 WM F EC 100% AUTO POWER 5 UNITY 6 2 50% GAIN/ ID PINS GAIN/PEAKING PEAKING 5 6 4 3 3 4 P/2 D
Summary of the content on the page No. 8
Controls and Installation, cont’d P/2 DA2 WM F/EC F rear panel P/2 DA2 D rear panel 1 2 NC 12-24V AC/DC L R 1 5 2 NORM MED NC 3 HIGH 12-24V AC/DC L R 4 3 P/2 DA2 WM F/EC F rear connectors Figure 2-5 — P/2 DA2 D rear connectors N Both WM F and WM EC F models have the same rear panel connectors. Configuration DIP switches — The three DIP switches (plus 1 Power input — 12 - 24 VAC or DC (captive screw connector). one spare) configure the P/2 DA2 D, as shown in the table 1 The center pole contains
Summary of the content on the page No. 9
Controls and Installation, cont’d 3 Gain switch — To compensate for cable resistance and Installing the P/2 DA2 WM F/EC F capacitance, use a small screwdriver to slide this switch to select the level of video gain that yields the sharpest, smear-free Easy setup procedure picture. The wall-mounted P/2 DA2 WM F kit consists of the faceplate/ Normal – distribution amplifier assembly and a mounting bracket that Unity gain mounts in a wall opening and to which the faceplate assembly is attached. The
Summary of the content on the page No. 10
Controls and Installation, cont’d 6 Power up all of the input and output devices. 7 The image should now display on screen. If it does not, NOTE Do not disassemble the dogleg double check steps 3 through 6 and make adjustments as from the dogleg screw. Rotate the needed. Refer to the section “Setting the DIP switches” in dogleg out of the way to insert the mud ring into the wall. this chapter. 8 For the P/2 DA2 WM F, attach the P/2 DA2 WM F to the wall mounting bracket (see “Installing the
Summary of the content on the page No. 11
Controls and Installation, cont’d Cabling Connecting audio output The P/2 DA2 WM F cabling diagram below shows how to Before connecting audio output, determine whether your audio connect input and output devices to the distribution amplifier’s system is unbalanced or balanced. Then, follow the instructions front panel. The P/2 DA2 WM EC F model has identical below to connect unbalanced audio, or the instructions for connectors. “Balanced audio” to connect balanced audio. C Wiring the audio inc
Summary of the content on the page No. 12
AUTO POWER AUDIO ID PIN 4 INPUT BUFFERED ID PIN 11 100% UNITY 50% LOCAL MONITOR GAIN/PEAKING P/2 DA2 WM F AAP Controls and Installation, cont’d Balanced audio To attach the distribution amplifier to a balanced audio system, do the following: Adapter Plate 1. Attach the audio cable to a balanced speaker input connector (tip, ring, and sleeve). Tip (L) Ring (R) #4-40 Nut w/ Captive Washer Sleeve ( ) P/2 DA2 WM F AAP 2. Attach the audio cable to the audio cable connector (Extron (up to 4 plates)
Summary of the content on the page No. 13
50% 100% UNITY 50% 100% UNITY AUTO POWER AUDIO ID PIN 4 INPUT BUFFERED ID PIN 11 100% UNITY 50% LOCAL MONITOR GAIN/PEAKING P/2 DA2 WM F 12 Controls and Installation, cont’d P/2 DA2 WM F wall mount installation P/2 DA2 WM EC F Euro Channel installation Once the input and output cables have been connected and the Once the input and output cables have been connected and P/2 DA2 WM F has been successfully tested, the faceplate may tested on the P/2 DA2 WM F EC, the distribution amplifier can be atta
Summary of the content on the page No. 14
Controls and Installation, cont’d Setting the internal jumpers Installing the P/2 DA2 D The jumpers (J2 and J6) inside the distribution amplifier are set The P/2 DA2 D is a wall-mounted product and can be mounted at the factory for output to a local monitor. However, you can into an electrical wall box. These instructions include site direct output to a data display by resetting the jumpers. Follow preparation, wall box installation, and the mounting of the these steps and the illustration be
Summary of the content on the page No. 15
Controls and Installation, cont’d 3. Mount the distribution amplifier to the wall box with Wall Stud Wall Stud machine screws, as shown in the following illustration. Installation Cable Installation Cable Cable Clamp Cable Clamp Wall Box Screws or Nails Screws or Nails Extron P2 DA2 D Wall opening is flush with edge of box. Attaching the wall box to a wall stud If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw threads must p
Summary of the content on the page No. 16
Controls and Installation, cont’d Replacing the faceplate P/2 DA2 WM/EC/D/AAP Series The front faceplate is replaced by removing the two rear panel mounting screws, replacing the faceplate, then reattaching the two screws, as shown below. NORM MED HIGH Mounting Back Panel Screws Faceplate (rear) P/2 DA2 D application example Appendix A An example of the P/2 DA2 D installation is shown below. Extron SI 3CT LP A Full-Range Ceiling Speakers Specifications, Dimensions, Parts, and Templates Projector
Summary of the content on the page No. 17
Specifications, Dimensions, and Parts Video output Specifications Number/signal type Video P/2 DA2 D ........................ 1 VGA–QXGA RGBHV, RGBS, RGsB, Gain RsGsBs, HDTV component video main P/2 DA2 D ........................ Main output: 0 dB, 0.6 dB, 1.2 dB, output selectable 1 VGA–QXGA RGBHV, RGBS, RGsB, Local monitor output: unity RsGsBs, HDTV component video local monitor output P/2 DA2 WM F, P/2 DA2 WM F AAP Switchable: 0 dB, +1.2 dB, +2.2 dB(0.7 V, P/2 DA2 WM F, P/2 DA2 WM F AAP 0.8 V
Summary of the content on the page No. 18
Specifications, Dimensions, Parts, cont’d Output impedance Audio output P/2 DA2 D ........................ 75 ohms Number/signal type P/2 DA2 WM F, P/2 DA2 WM F AAP P/2 DA2 D ........................ 1 stereo or dual mono (switch selectable), 40 ohms, typical balanced/unbalanced Max. propagation delay P/2 DA2 WM F, P/2 DA2 WM F AAP P/2 DA2 D ........................ 60 ns 1 stereo, balanced/unbalanced P/2 DA2 WM F, P/2 DA2 WM F AAP Connectors ................................... (1) 3.5 mm direct
Summary of the content on the page No. 19
Specifications, Dimensions, and Parts, cont’d P/2 DA2 WM F Dimensions Faceplate ................... 4.5” H x 4.6” W x 0.1” D Dimensions of the P/2 DA2 WM F and its AAP version are (11.4 cm H x 11.7 cm W x 0.3 cm D) provided here for those who wish to make their own (2 gang) customized faceplates. The following diagrams are not drawn Box ............................. 2.6” H x 3.7” W x 1.6” D to scale. (6.6 cm H x 9.4 cm W x 4.1 cm D) All dimensions are given in inches. P/2 DA2 WM F AAP Faceplate
Summary of the content on the page No. 20
Specifications, Dimensions, and Parts, cont’d P/2 DA2 WM F AAP faceplate dimensions P/2 DA2 D faceplate dimensions .060 [1.524] .600 [15.500] .100 [2.540] 2.830 [71.882] 0.000 [0.000] 2.720 [69.088] 0.110 [2.794] 2.720 [70.000] 0.000 [0.000] WM F AAP model faceplate dimensions Front View Side View D model faceplate dimensions A-8 P/2 DA2 WM/EC/D/AAP Series � Appendix P/2 DA2 WM/EC/D/AAP Series � Appendix A-9 .000 [0.000] .0000 [0.000] 2X 0.050 [1.270] 0.155 [3.937] 1.445 [36.703] 1.550 [39.370]
