Summary of the content on the page No. 1
User’s Manual
P/2 DA2xi
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01 Kyodo Building Distribution Amplifi er
Anaheim, CA 92805 3821 AH Amersfoort PM Industrial Building 16 Ichibancho
USA The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0082 Japan
714.491.1500 +31.33.453.4040 +65.6383.4400 +81.3.3511.7655
68-1239-01 Rev. A
www.extron.com Fax 714.491.1517 Fax +31.
Summary of the content on the page No. 2
Precautions Safety Instructions � English Warning FCC Class A Notice Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety Note: This equipment has been tested and found to comply with the limits f
Summary of the content on the page No. 3
� � � � � � � � � � �
Summary of the content on the page No. 4
Description The P/2 DA2xi is a high performance one input, two output distribution amplifi er that accepts video input from a VGA- QXGA compatible PC and distributes that signal to separately buffered outputs. The output can be extended with Extron MHR cables up to 250' in length (XGA resolution signal). The P/2 DA2xi routes all video ID bits to its local monitor output to allow for automatic resolution selection by DDC1 and DDC2 (plug and play cards and projector). Features � Power LED —
Summary of the content on the page No. 5
Installation and Operation, cont’d On the non-VersaTools rack shelves, the unit can be mounted Mounting the P/2 DA2xi in the front or the rear of the rack, as shown in the following Installation and service must be performed by C illustration. authorized personnel only. 1. Remove the feet from the bottom of the P/2 DA2xi, if they The 1" high, quarter rack width P/2 DA2xi can be placed on are installed. a tabletop, mounted on a rack shelf, mounted under a desk or 2. Mount the unit using t
Summary of the content on the page No. 6
Installation and Operation, cont’d 1. Secure the under-desk mounting brackets to the distribution amplifi er with the four machine screws provided in the mounting kit. VersaTools Rack Shelf 2. Hold the unit with attached brackets against the underside of the desk or other furniture. Mark the location of holes for screws on the desk. 3. Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot holes in the table or desk at the marked screw locations from the underside or inside (the concealed
Summary of the content on the page No. 7
Installation and Operation, cont’d 1. Loosely attach the mounting brackets to the unit using The PMK 350 Low Profi le Projector Mount Kit is an above- the four machine screws and washers supplied with the projector mounting kit that attaches to a 1" to 2" diameter mounting kit. projector mounting pole. It can hold more than one device, in a variety of sizes. The PMK 350 is available in black 2. Hold the distribution amplifi er against the inside of the (part #70-563-02) or white (part #70-5
Summary of the content on the page No. 8
Installation and Operation, cont’d 10. Secure the L-shaped bracket to the square U-bolt using the Front Panel Features included hex nuts, washers, and lock washers. Tighten the INPUT hex nuts securely. Be sure to tighten the hex nuts securely enough that the N PMK 350 does not slide down the ceiling pole. A socket wrench is recommended to tighten the hex nuts. 1 2 11. Secure the front panel to the mounting tray with four of the included #6 screws. Power LED indicator — a 12. If de
Summary of the content on the page No. 9
AA Installation and Operation, cont’d The blue connector does not have the extended tail or the Output connector — Connect the display device to the 15-pin d included tie-wrap. HD connector. Do not tin the power supply leads before installing in N the direct insertion connector. Tinned wires are not as Power supply wiring secure in the connectors and could be pulled out. Wire the P/2 DA2xi's power connector, as shown below. Operation Smooth After the distribution amplifi er and its con
Summary of the content on the page No. 10
Installation and Operation, cont’d Output level .................................. TTL, 4 V to 5 Vp-p, unterminated Specifi cations Input impedance .......................... 510 ohms Output impedance ....................... 75 ohms or 55 ohms, switchable (output Video impedance resistors are 50 and 30 ohms) Gain ................................................ Selectable: 0.7 V (unity), or 0.75 V Max input voltage ........................ 5.0 Vp-p Peaking .................................
Summary of the content on the page No. 11
Installation and Operation, cont’d Warranty ........................................ 3 years parts and labor Cables All nominal levels are at ±10%. Description Part number M6' MHR cable — 6' (1.8 m) 26-238-01 Specifi cations are subject to change without notice. M15' MHR cable — 15' (4.5 m) 26-238-02 M50' MHR cable — 50' (15.2 m) 26-238-18 M75' MHR cable — 75' (22.8 m) 26-238-19 Included Parts M100' MHR cable — 100' (30.4 m) 26-238-20 Description Part number SY VGAM-RGBHVM — 6' (1.8 m) 26-533
