Summary of the content on the page No. 1
Model AXTM-600
600 Watt Mono Block
MOSFET Amplifier
OWNER'S
MANUAL
Summary of the content on the page No. 2
INDEX Specifications.....................................................................3 Precautions........................................................................4 Installation Instructions...................................................... 5 Wiring Instructions........................................................ 6 - 7 Input Wiring Diagram........................................................ 8 Output Wiring Diagram..................................................... 9 Oper
Summary of the content on the page No. 3
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high Quality performance with a HELP! minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed. We therefore advise that you 1-800-645-4994 read these instructions very carefully to familiarize yourself with the product and it's features. Monday-Friday 8:30am - 7:00pm Eastern Should you require assistance with the installation or wirin
Summary of the content on the page No. 4
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery. Connect this + + wire only after having completed and checked all other connections to the amplifier. 3. By nature of its design, a power amplifier generates heat and require
Summary of the content on the page No. 5
INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. 3. Remove the amplifier and drill a 1/8" hole at each of the four locations. CAUTION: Befor
Summary of the content on the page No. 6
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using. The power and speakers wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wi
Summary of the content on the page No. 7
WIRING INSTRUCTIONS 4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess of 10 feet, #14 gauge is recommended. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the p
Summary of the content on the page No. 8
INPUT WIRING DIAGRAM CAR STEREO Left Speaker Right Speaker Gray Brown Black RCA TYPE SHIELDED Green EXTENSION CABLES White (NOT INCLUDED) IMPORTANT HIGH-LEVEL (SPEAKER) INPUT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. (WIRE SIDEVIEW) LOW-LEVEL INPUT H HI- I-IN INP PU UT T X X- -O OV VE ER R P PW WR R R R L L + + R R + + L L R R P PR RT T L LP PF F F FU UL LL L G GN ND D M MIN IN M MA AX X 5 50 0H Hz z 1 12 20 0H Hz z 0 0d dB B 1 18 8d dB B 4 40 0H Hz z 8 80 0H Hz z L L G GA AIN IN L
Summary of the content on the page No. 9
OUTPUT WIRING DIAGRAM EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. GROUND METAL SECTION OF VEHICLE F FU US SE E SPEAKER BATT REM GND USE #10 GAUGE WIRE (SEE TEXT) SPEAKER2(MONO) 2-8 OHM GROUND CAR STEREO BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD -9-
Summary of the content on the page No. 10
OPERATION 2 1 3 5 4 8 7 6 H HII- -IIN NP PU UT T X X- -O OV VE ER R F FU US SE E P PW WR R R R L L + + R R + + L L R R P PR RT T L L P P F F H H P P F F G GN ND D F FU UL LL L 5 50 0H Hz z 2 25 50 0H Hz z M MI IN N M MA AX X 0 0d dB B 1 18 8d dB B 5 50 0H Hz z 2 25 50 0H Hz z L L H HP PF F G GA AI IN N B BA AS SS S L LP PF F B BO OO OS ST T BATT REM GND SPEAKER1 SPEAKER2 After initial set-up, the amplifier should not require any Off to a normal operating range. If activated by an further ad
Summary of the content on the page No. 11
If, however, there is still output from the amplifier when 6 HPF Crossover Frequency Control the car stereo volume control is at its minimum setting, This Control selects the crossover frequency when the or the output level increases too fast with a small 4 Sub woofer Crossover Selector is in the "HPF" setting. rotation of the volume control, adjust the Level control Adjust it to the appropriate position for the characteristics to decrease the output from the system. and crossover frequ
Summary of the content on the page No. 12
90 DAY/12MONTH LIMITED WARRANTY 90 DAY/12MONTH LIMITED WARRANTY Applies to car stereo power amplifiers, equalizers and accessories. Applies to car stereo power amplifiers, equalizers and accessories. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaire
Summary of the content on the page No. 13
C C 2003 Audiovox Electronics Corporation, Hauppauge, N.Y. Printed in Korea 128-6558
