Infinity TSS-FMK4000 user manual

Summary of the content on the page No. 1

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 1
TSS-4000
TOTAL SPEAKER SOLUTIONS
TSS-FMK4000
Owner’s Guide

Summary of the content on the page No. 2

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 2 INTRODUCTION The TSS-FMK4000 allows you to recess a TSS-SAT4000 or TSS-CENTER4000 into the wall.When installed, the speaker will extend beyond the wall approximately 1" . Unpacking the Components Finish unpacking the flush-mount kit and check the contents. If you suspect damage from transit, report it immediately to your dealer. Keep the shipping carton and packing materials for future use. Contents Please verify that the package contains the f

Summary of the content on the page No. 3

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 3 Important Notes: 1) In order to horizontally flush-mount the TSS-CENTER4000 in a wall with standard 16" spacing between the studs, some modification to that area of the wall will be necessary.This type of installation will require a professional licensed contractor to install horizontal braces that comply with the customer’s local building codes. 2) For a satellite installation, follow all the steps but cut the hole in a vertical direction, perp

Summary of the content on the page No. 4

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 4 Step Three After you have found the correct placement on the wall for the speaker, use the template provided to draw the exact-sized hole required. Make sure to use a level when positioning the template to ensure that your installation is level.Then cut out the drywall to create the hole. Wall NOTE: The hole for the speaker should be 22-1/2" x 4-3/8." Template Screw Holes Step Four Place the mounting blocks inside the hole at either end. Use t

Summary of the content on the page No. 5

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 5 Step Five Attach speaker wires as described in the speaker’s owner’s manual and, using four #8 x 1-1/8" pan-head wood screws provided, screw the speaker assembly into place, making sure that the screws anchor themselves into the mounting blocks behind the drywall. (4) #8 x 1-1/8" Pan-Head Wood Screws Step Six Apply the sealing strips to either side of the speaker to cover the remaining openings of the cutout in the drywall. Sealing Strip 5 TSS-

Summary of the content on the page No. 6

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 6 Step Seven Remove the paper cover from the gasket on the speaker-facing side of the frame. Place the frame over the in-wall assembly and snap it into place. Remove Paper Cover From Gasket Frame Center Speaker In-Wall Installation 6 TSS-FMK4000

Summary of the content on the page No. 7

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 7 Satellite Installation Exploded View For satellite installation, repeat the steps but cut the hole in a vertical direction, perpendicular to the floor. Satellite Speaker In-Wall Installation 7 TSS-FMK4000

Summary of the content on the page No. 8

INFP1614tss4000FMK-OM 10/29/04 11:39 AM Page 8 © 2004 Harman International Industries, Incorporated Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (USA only) www.infinitysystems.com Infinity is a registered trademark, and Total Solutions is a trademark, of Harman International Industries, Incorporated. Part No. 400-OMINKIT 10/04 Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and constructio