Summary of the content on the page No. 1
ISIS WideLine Loudspeaker User Manual
Model WL 2102
*TD-000188-00*
TD-000188-00 rev.A
Summary of the content on the page No. 2
IMPORTANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation, placement or array. Any such condition sev
Summary of the content on the page No. 3
This provides smoother pattern control at the mid-high cross- Introduction over. With selectable shading, the enclosures can be used as The WideLine loudspeaker system has been designed to pro- house right or left by flipping the switch, not the enclosure. vide a compact system that has similar power handling, fre- quency response, and coverage of larger systems. Its primary The enclosure is constructed of lightweight cored-composite uses include ballrooms, theatres, night clubs, houses of w
Summary of the content on the page No. 4
Three way Active/Two way Active Switch Two way active: The “full range” LF input is applied to pins 1+ and 1- and the -6dB per octave shading network is applied to one of the LF transducers using the Low Frequency Select switch (above). Three way active: Shading network is NOT applied (shading must be provided by upstream signal pro- cessing). Connect the full-range input signal to pins 1+ and 1-, connect the shaded (processed) signal to pins 2+ and 2-. To flip shaded transducer location, use
Summary of the content on the page No. 5
Input Connections The input connectors are a pair of Neutrik NL8's wired in parallel. Connections for biamp and tri- amp vary, see Table 1. The pin designations for the NL8FC cable connector is shown for reference, bottom right. Note! In three way mode, the Low Frequency Select switch position determines the input connector wiring! Unexpected results may occur if switch positions and wir- ing are not strictly controlled. The WideLine loudspeaker is not equipped with a crossover network. All s
Summary of the content on the page No. 6
Rigging CAUTION: SUSPENDING SPEAKERS PRESENTS A RISK OF SERIOUS INJURY OR DEATH. PLEASE USE CAUTION TO ASSURE THAT MOUNTING SURFACES ARE CAPABLE OF SUPPORTING AT LEAST Front Articulated FIVE TIMES THE WEIGHT OF THE SPEAKER AND MOUNTING APPARATUS. Joint- Slide the joint USE ONLY LOAD RATED HARDWARE. ALWAYS CONSULT WITH A CERTIFIED out of the receiver tube PROFESSIONAL WHEN IMPLEMENTING OVERHEAD SUSPENSION. by sliding the retaining screw upward, then The large array frame’s maximum arra
Summary of the content on the page No. 7
Adjusting the Angle Between Enclosures (Splay) The illustration shows the rear pin block of two enclo- sures joined by the upper enclosure’s rear link arm. Use the first pin location (closest to the end) on the link arm for setting in normalized 2° increments. The left- side example shows two enclosures linked for 8° of splay. The ball-lock pin is inserted into the 8° position in the rear block while passing through the “normal” pin hole in the link. When the "+3" location is used, an addi
Summary of the content on the page No. 8
Large Array Frame (continued) The mounting plate and link on are located on the bottom side of the frame assembly. Use this link for attaching the rear of the first enclosure. The grid allows for up or down angle options for use with either stacking or flying. The 4° “normal” locations on the link sys- tem will yield a net 0° vertical inclination. Use 4° link location for 0° vertical inclination Small Array Frame (Stacking Grid) Do not fly (suspend) more than eight (8) enclosures form the sma
Summary of the content on the page No. 9
Stacking the Small Array Frame The small array frame comes with two aluminum I-bars used for aligning and securing the frame to QSC’s “215” subwoofer. To use the I-bars, simply slide each one into the small frame’s L-track and secure with a stud fitting. Then, turn the frame over (I-bars on the bottom) and slide the exposed I-bars into the subwoofer’s L-track. Secure the I-bar with a stud fitting. Note that the stud fittings used are not required to be load rated as they only retain the I-bars
Summary of the content on the page No. 10
Preliminary System Specifications (subject to change without notice) Configuration: Three way, biamp (active two way) or triamp (full three way active) Frequency Response: 52Hz - 18KHz (+/- 3dB) Sensitivity: biamp: 97dB (2.83v @ 1m) triamp: 99dB (2.83v @ 1m) Nominal coverage: Horizontal:140deg. Vertical: Dependant on number of elements used Nominal Impedance: 8 ohms, low frequency in biamp mode, 16 ohms low frequency in triamp mode 16 ohms, high frequency Transducers: Low Frequency: two 10" (254
Summary of the content on the page No. 11
Dimensions 11
Summary of the content on the page No. 12
How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA Telephone Numbers: Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service (714) 957-7150 or toll free (USA only) (800) 772-2834 Facsimile Numbers: Sales & Marketing FAX (714) 754-6174 Customer Service FAX (714) 754-6173 World Wide Web: www.qscaudio.com E-mail: info@qscaudio.com service@qscaudio.com Warranty
