Summary of the content on the page No. 1
Instruction Manual
For the digital camera
CAMEDIA C-5000 Zoom
Waterproof Case
PT-019
Thank you for buying the Waterproof Case PT-019.
Please read this instruction manual carefully and use the product safely
and correctly.
Please keep this instruction manual for reference after reading it.
Wrong use may cause damage to the camera on the inside from water
leakage, and repair may not be possible.
Before use, perform an advance check as described in this manual.
Summary of the content on the page No. 2
Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. Our company shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product. Our company shall not be responsible for damage, lost profits, etc. caused by loss of image data because of defects, disassembly, repair or modification of this product b
Summary of the content on the page No. 3
WARNING 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which open and close. Swallowing of small parts. Please consult a physician immediately if any parts have been swallowed. Triggering of the flash in front of the eyes may cause permanent vision impairment etc. 2. Do not store with a b
Summary of the content on the page No. 4
5. Jumping into the water with the Case in your pocket or in your hand, throwing the Case from a boat or ship into the water, and other rough handling may cause water leakage. Please handle with sufficient care, when handing it over from hand to hand etc. 6. If the camera on the inside should become wet because of water leakage etc., immediately wipe off all moisture and confirm the operation. 7. Please remove the O-ring when traveling by air. Otherwise air pressure may make it impossible to ope
Summary of the content on the page No. 5
For Prevention of Water Leakage Accidents When water leakage occurs while this product is being used, repair of the camera housed in this product may become impossible. Please observe the following cautions for use. 1. When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick not only to the O-ring, but also to the contact surface (flat part of the front cover). Even a single hair or a single grain of sand may cause water leakage. Please check with
Summary of the content on the page No. 6
8. When the O-ring contact surface is pressed strongly from the outside of the Case, or when the Case is twisted, the waterproof function may be lost. Take care not to exert excessive force. 9. Please be sure to perform the advance test and the final test each time before using the case. 10.If you should notice drops of water or other signs of water leakage while taking pictures, immediately stop the dive, remove any water from the camera and the product, test according to the item "Final check"
Summary of the content on the page No. 7
Chemicals which cannot be used Explanation Do not clean the Case with alcohol, gasoline, thinner Volatile organic solvents, or other volatile organic solvents or with chemical chemical detergents detergents etc. Pure water or lukewarm water is sufficient. Do not use anticorrosion agents. The metal parts use Anticorrosion agent stainless steel or brass, and washing with pure water is sufficient. Commercial defogging Do not use commercial defogging agents. Always agents use the specified desiccant
Summary of the content on the page No. 8
Contents Introduction E-1 Please read the following items before use E-1 For safe use E-1 Batteries E-3 For Prevention of Water Leakage Accidents E-4 Handling the Product E-5 Contents E-7-8 1. Preparations E-9 Check the contents of the package. E-9 Names of the parts E-10 Install the strap. E-11 Master the basic operation. E-11 Holding the Case E-11 How to Press the Shutter E-12 How to Use the Mode Dial E-12 How to Use the Zoom Lever E-12 Setting the Zoom Lever E-13 Power Switch Opera
Summary of the content on the page No. 9
Install the special balance weight. E-18 Installation and Removal of the LCD Hood E-19 Installation E-19 Removal E-19 Mounting and Removing the Lens Cap E-20 Perform the final checks. E-20 Visual Inspection E-20 Set the power to 'ON'. E-20 Try to move the mode dial. E-20 Final Test E-21 4. Taking Pictures Under Water E-22 How to Use the Hand Strap E-22 Take pictures carefully. E-22 Confirm the picture on the LCD monitor. E-22 Quietly press the shutter lever. E-22 Cautions when usi
Summary of the content on the page No. 10
1. Preparations Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged. LCD hood Silica gel Silicone grease (on the body) Case body LCD hood strap Hand strap Lenscap Balance weight (Check that the O-ring is normal.) Pick for O-ring removal Instruction manual (this manual) Guarantee card Please read before use Instruction Manual For the digital camera CAMEDIA C-5000 Zoom Waterproof Case Read this first about y
Summary of the content on the page No. 11
Names of the parts Palm Grip ❈ LCD monitor button Loading guide rail Buckle lock lever ❈ OK/Menu button LCD monitor window Buckle hook ❈ Arrow Pad Grease for silicone O-ring(white cap) Diffuser and diffuser cover ❈ AEL/Custom button Silica gel O-ring ❈ Flash mode button Balance weight ❈ Shutter lever ❈ Macro/Spot button Pick for O-ring removal ❈ Zoom lever ❈ Selftimer button LCD inner hood Hand strap ring ❈ Flash lever LCD hood Hand strap ❈ Flash close lever LCD hood strap Tripod sea
Summary of the content on the page No. 12
Install the strap. Install the strap on the Case body. Installation explanation Finished installation Hand strap Hand strap ring : Please install the strap correctly as shown above. Our company CAUTION shall bear no responsibility for damage etc. caused by dropping the Case because of incorrect installation of the strap. Master the basic operation. Please master the basic operation of the Case before taking pictures. Holding the Case Hold the Case securely with both hands, keep your elbows clos
Summary of the content on the page No. 13
How to Press the Shutter When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Advice • If you use your index finger to operate the shutter release lever and your middle finger for the zoom lever, you will not need to change your finger position. • Before activating the shutter release lever, the zoom lever should be in the neutral (middle) position. The release cannot be activated if the zoom lever is in the tele or wide-angle position. • For more de
Summary of the content on the page No. 14
Setting the Zoom Lever When loading the digital camera in the Case, fit the projecting part of the zoom lever of the digital camera into the recessed part of the zoom lever on the inside of the Case. CAUTION : • When loading the camera, confirm that the projecting part of the zoom lever of the camera is properly set to the recessed part of the zoom lever of the Case. • When the setting is insufficient, the loading of the camera becomes imperfect and it may not be possible to seal the Case or zoo
Summary of the content on the page No. 15
2. Advance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications. However, depending on the carrying and storage conditions, the maintenance status, etc., the waterproof function may be damaged.
Summary of the content on the page No. 16
3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation Since the LCD monitor is used for picture confirmation while taking pictures under water, the battery life becomes short. Confirm that the remaining battery capacity is sufficient. Note:• In order to avoid losing shutter chances due to an exhausted battery, you should always replace a battery with a fully charged battery before each dive. Confirmation of the Remai
Summary of the content on the page No. 17
Open the Case. Insert the buckle opener of the accessory into the buckle opening lever as shown in the figure (in direction ) Pull the buckle opener slowly (in direction ). When not using the buckle opener, hold the buckle opening lever with your thumb and index finger from the side and pull it up slowly. Pull the mode dial of the Case. Pull the mode dial of the Case until it stops, so that it does not interfere with the mode dial of the digital camera. Load the digital camera. Quietly load t
Summary of the content on the page No. 18
Set the mode dial. After the digital camera has been loaded, push down the mode dial of the Case from the upper surface of the Case. Set it so that the lower part of the mode dial on the inside of the Case fits properly onto the upper part of the mode dial of the digital camera itself. Also, load the camera so that the power switch of the digital camera fits into the power switch lever notch on the inside of the protector. Advice • After setting the mode dial of the Case, set the power of the d
Summary of the content on the page No. 19
Check the loading status. Always perform the following final checks before sealing the Case. Has the digital camera been loaded so that the zoom lever operates properly? Has the silica gel been inserted all the way at the specified position? Has the O-ring at the Case opening part been installed properly? Are the O-ring and the O-ring contact surface on the front lid free of dirt and other foreign matter? Seal the Case. When the rear lid is closed (quietly, so that the O-ring will not co
Summary of the content on the page No. 20
Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. Removal Remove the mounting projections of the LCD hood from the guides above and below the LCD monitor window by widening the LCD hood. Installation Removal E-19
