Summary of the content on the page No. 1
LCi-IP SERIES
LC80i-IP
LC265i-IP
Active In-Wall/In-Ceiling Speakers
Owner’s
Manual
Summary of the content on the page No. 2
• The LC265i was the first in-wall speaker to feature LCi-IP SERIES SPECIFICATIONS ENGLISH ment. What’s more, LCi-IP speakers already come with an the patented Power Port™ bass venting system for award-winning reputation, because they use the same Model LC80i-IP IMPORTANT SAFETY INSTRUCTIONS superior bass response with low distortion. driver technologies as Polk Audio's award winning READ BEFORE OPERATING EQUIPMENT Freq. Response
Summary of the content on the page No. 3
INSTALLING LCi-IP SPEAKERS Important Note: If installing LCi-IP speakers in Cable runs up to 100 feet should have a capacitance INSTALLING THE CONNECTING LCi-IP SPEAKERS TO LCi-IP PERFORMANCE an external wall, the operating ambient temperature of of 20pF/ft. For cable runs greater than 100 ft. call NETWORK DECODER CARD A NETWORK OR ANALOG SYSTEM OPTIMIZATION WIZARD PROGRAM INSTALLATION RECOMMENDATION the speakers is 0-50° C (32-122° F). For most types of Customer Serivce at 1-800-377-7655. FOR O
Summary of the content on the page No. 4
Making A Speaker Configuration File Offsite INTERPRETING THE LEDS FAQs To help you work more efficiently and save time, An LED indicator tells you the status Will the speakers work with my What happens to the speaker settings if you can make a speaker configuration file offsite. of each speaker: current MRAV system? I temporarily lose power? You will need to have installed the speakers, be An ORANGE LED indicates the speaker Please check with your MRAV Authorized Installer. If you are using the
Summary of the content on the page No. 5
TROUBLESHOOTING CONTINUED TROUBLESHOOTING Problem Possible Reason(s) Solution Problem Possible Reason(s) Solution No LED Room is too bright. The LED found on the front baffle of the speaker is intentionally soft as No audio Audio signal is not connected to the speaker. Make sure that the speaker is connected to the audio source using RCA to not distract the user during operation. Make sure the speaker grill cables or a RJ45 equipped Cat-5 cable. Make sure that the configuration is removed a
Summary of the content on the page No. 6
Disconnect all cables. Disconnect all cables. 1 Disconnect all cables. Disconnect all cables. Remove the (4) Torx screws (size T-10) holding the heat Disconnect all cables. sink to the amp housing. Set the screws safely aside. Hookup 2 Disconnect all cables. Remove the (4) Torx screws (size T-10) holding the heat sink to the amp housing. Set the screws safely aside. Remove the (4) Torx screws (size T-10) holding the heat sink to the amp housing. Set the screws safely aside. Remove the (4) Torx
Summary of the content on the page No. 7
(Independent Control) Hookup Hookup OPTIONAL CHANNEL 1 CHANNEL 1 CHANNEL 1 CHANNEL 2 CHANNEL 2 CHANNEL 2 NETWORK IN NETWORK IN NETWORK IN COMM COMM COMM Y 1 Y Y A 1 A A 1 N B 2 N B 2 N B 2 CONTROL CFG CHANNEL CONTROL CFG CHANNEL CONTROL CFG CHANNEL* * Channel can be 1 or 2 depending on configuration. Hookup Hookup CHANNEL 1 CHANNEL 1 CHANNEL 1 CHANNEL 1 CHANNEL 2 CHANNEL 2 CHANNEL 2 CHANNEL 2 NETWORK IN NETWORK IN NETWORK IN NETWORK IN COMM COMM COMM COMM Y 1 Y 1 A A N B 2 N B 2 Y
Summary of the content on the page No. 8
CENTER CHANNEL Hookup 5a: ANALOG (Independent Control Hookup When Used with Hookup 3a or 3b) CHANNEL 1 CHANNEL 1 CHANNEL 1 CHANNEL 2 CHANNEL 2 CHANNEL 2 NETWORK IN NETWORK IN NETWORK IN COMM COMM COMM Y 1 Y A 1 A Y A 1 N B 2 N B 2 2 N B CONTROL CFG CHANNEL CONTROL CFG CHANNEL CONTROL CFG CHANNEL CENTER CHANNEL Hookup 5b: ANALOG (Independent Control When Used with Hookup 4a or 4b) CHANNEL 1 CHANNEL 2 NETWORK IN COMM Y A 1 N B 2 CONTROL CFG CHANNEL 44 Polk Audio Customer Service:
Summary of the content on the page No. 9
CAUTION ATTENTION RISK OF ELECTRIC SHOCK RISQUE D’ÉLECTROCUTION DO NOT OPEN NE PAS OUVRIR CAUTION ATTENTION 230 RISK OF ELECTRIC SHOCK RISQUE D’ÉLECTROCUTION DO NOT OPEN NE PAS OUVRIR ON 230 AC MAIN ON OFF 120 AC MAIN OFF 120 INPUT: 90-132 OR 180-264 VAC 7.4/3.7A (50-60Hz) OUTPUT: +48V (7.3A)350W INPUT: 90-132 OR 180-264 VAC F10AL250W 7.4/3.7A (50-60Hz) OUTPUT: +48V (7.3A)350W F10AL250W This hookup works for both the LC265i-IP and the LC80i-IP. This hookup works for both the LC265i-IP and
Summary of the content on the page No. 10
NOTES LIMITED WARRANTY Polk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate automatically prior to its stated expiration if the original retail purchaser sells or transfers the Product to any other party. Polk Audio, Inc., warrants, to the original retail purchaser only, that the LCi-IP Speaker on this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of five (5) years from the date of original retail purc
Summary of the content on the page No. 11
5601 METRO DRIVE BALTIMORE, MARYLAND 21215 800-377-7655 (US & CAN, OUTSIDE US 410-358-3600) WWW.POLKAUDIO.COM “Polk Audio,” “Dynamic Balance” and “Acoustic Resonance Control” are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated.
