Summary of the content on the page No. 1
INSTALLATION GUIDE
FOR USE IN MULTI-CHANNEL MUSIC OR HOME THEATER SYSTEMS
HIGH DEFINITION, SIDE/REAR CHANNEL EFFECTS, IN-WALL LOUDSPEAKERS
HDFX
Summary of the content on the page No. 2
CONGRATULATIONS! Thank you for choosing HDFX High-Defi nition, Side-/Rear-Channel Effects, In-Wall Loudspeakers from Niles. With proper installation and operation, you should enjoy years of trouble-free use. Niles manufactures the industry’s most complete line of custom installation components and accessories for audio/video systems. To see the complete Niles product assortment, visit us on the Internet at: www.nilesaudio.com TABLE OF CONTENTS Introduction 1 Features and Benefits 1 Installat
Summary of the content on the page No. 3
INTRODUCTION Niles HDFX High-Defi nition, Side-/Rear-Channel Effects, In-Wall Loudspeakers are expressly designed for superior sonic quality in side- or rear-channel applications. They employ advanced technology components that extract the subtle nuances in recorded music or the thunderous action sound in a movie. HDFX loudspeakers are the perfect choice wherever quality of sound is the most important consideration. FEATURES AND BENEFITS 5-1/4-INCH INJECTION-MOLDED TCC WOOFER WITH BUTYL-RUBB
Summary of the content on the page No. 4
BIPOLE/DIPOLE AND FX/CUT SWITCHES The HDFX also includes a baffl e-mounted BIPOLE/DIPOLE mode switch so the installer can set the sur- round effects for either side or rear placement. A companion FX/CUT switch allows adjustment of the direct/diffuse sound fi eld balance to provide realistic effects, regardless of room size. EASY RETROFIT INSTALLATION IN YOUR EXISTING HOME Designed for ease of installation, the Niles mounting system makes retrofi t installations simple and fast. A supplied templ
Summary of the content on the page No. 5
INSTALLATION CONSIDERATIONS Bracket New Construction Wings Frame Loudspeaker Baffl e Grille Acoustic Fine Tuning Controls Figure 1. Mounting an HDFX vertically into a wall 3 NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373
Summary of the content on the page No. 6
TOOLS AND PRECAUTIONS We recommend using the following tools to install an HDFX loudspeaker: • Electric drill with 1/4- and 1/2-inch drill bits, and a 1-inch flat drill bit (for drilling through studs) • Keyhole or drywall saw • Stiff wire, fish tape, or glow rods (for routing cables) • Phillips screwdriver set • Cable ties • Pencil • Level • Rubber gloves and protective eyewear Before starting the installation, please observe the following precautions: • Tu
Summary of the content on the page No. 7
LOUDSPEAKER WIRE Use 2-conductor loudspeaker wire when connecting loudspeakers to your receiver or amplifi er. For most applications, we recommend using 16- or 18-gauge wire. For wiring runs longer than 80 feet, we recommend 14-gauge wire. The spring-loaded terminals of the HDFX will accommodate up to 12-gauge wire directly. Larger sizes can be accommodated via pin connectors. When running wire inside walls or ceilings, use special jacketed cable (CL-2 or CL-3) to protect the wire and for fi r
Summary of the content on the page No. 8
LOUDSPEAKER PLACEMENT NOTE: THE NILES HDFX LOUDSPEAKER IS DESIGNED FOR USE IN SIDE- OR REAR-CHANNEL APPLICATIONS ONLY. FOR FRONT-OR CENTER-CHANNEL APPLICATIONS, WE RECOMMEND USING A NILES HDLCR OR HDLCRBX LOUDSPEAKER PLACEMENT FOR HOME THEATER REAR APPLICATIONS In home theater, the goal is to reproduce the experience of a great movie theater in your home. The biggest difference between the two venues is the use of a rear- or surround-loudspeaker array in a commercial theater. Here, it is not
Summary of the content on the page No. 9
Figure 2. HDFX loudspeakers are placed Figure 3. HDFX loudspeakers are placed near back corner walls of a home theater room. near back corner walls of a home theater room with an L-shaped sofa. • If your home theater system is capable of reproducing Dolby EX surround sound, consider using a second pair of HDFX loudspeakers (on the side walls) for an additional rear surround effect, as shown in Figure 4 (on the next page). Ideally, the side loud- speakers should be placed in-line with the
Summary of the content on the page No. 10
PLACEMENT FOR HOME THEATER REAR APPLICATIONS (CONTINUED) Figure 4. Two pairs of HDFX loudspeakers reproduce Dolby EX surround sound in a home theater room. THE BOUNDARY EFFECT Placing a loudspeaker in a corner can powerfully affect the way a listener perceives bass response. Known as the boundary effect, placing loudspeakers close to a wall/ceiling boundary or near a corner-wall boundary will emphasize certain bass frequencies, while canceling others. This effect can make the loudspeaker s
Summary of the content on the page No. 11
INSTALLATION FUNDAMENTALS RUNNING THE LOUDSPEAKER WIRE IN NEW CONSTRUCTION IMPORTANT: IF YOU HAVE DOUBTS ABOUT WHETHER YOU ARE CAPABLE OF INSTALLING A NILES WALL-MOUNT LOUDSPEAKER, PLEASE CONSULT A NILES DEALER OR PROFESSIONAL INSTALLER. THEY HAVE SPECIAL TOOLS, TECHNIQUES, AND EXPERIENCE TO MAKE THE IMPOSSIBLE JOB POSSIBLE. THE INSTALLER CAN PROVIDE YOU WITH AN ESTIMATE BEFORE ANY WORK IS DONE. OBSERVE SAFETY FIRST! • Always wear gloves, safety goggles, and head protection gear when dri
Summary of the content on the page No. 12
RUNNING THE LOUDSPEAKER WIRE IN NEW CONSTRUCTION (CONTINUED) ABOUT DRILLING Use a bit that is large enough for the wires you plan to run. This is an important consideration, since you may be drilling a lot of holes. Here are some additional tips: • We recommend using an auger bit for rough-in wiring. It will actually pull itself through the wood, so that the drill motor, not you, does most of the work. • Always drill the holes in the center of the stud. If you have to notch the stud o
Summary of the content on the page No. 13
CONCEALING LOUDSPEAKER WIRE ABOUT INTERIOR WALLS Interior walls in almost all North American residences are hollow, so they are easy installation sites for fl ush mounting loudspeakers and routing new loudspeaker cable in the house. Looking at a painted wallboard, plaster, or paneling, you only see the skin of the wall. Behind it is the home’s skeleton; 2-by-4 inch wood or metal “studs” running vertically from the fl oor to the ceiling in walls and 2-by-6 inch or larger “joists” running horiz
Summary of the content on the page No. 14
CONCEALING LOUDSPEAKER WIRE (CONTINUED) PLANNING THE LOUDSPEAKER WIRE ROUTE (CONTINUED) To fi nd exactly where an electrical cable is routed, try inspecting the inside of the wall by turn- ing off the breaker for a particular power outlet or switch, removing the cover plate and switch or receptacle, and then shining a penlight into the wall. If you have access to an attic or base- ment space, you can quickly see which part of the wall space is free of obstructions, as shown in Figure 7. Figure
Summary of the content on the page No. 15
OTHER POSSIBLE LOUDSPEAKER WIRE ROUTES INCLUDE: • Under-the-carpet runs using flat loudspeaker wires. • Heating and air conditioning vents used as wire raceways for plenum-rated wire. NOTE: CHECK YOUR LOCAL BUILDING CODES, SINCE SOME MUNICIPALITIES REQUIRE CONDUIT. CUTTING HOLES In traditional wood stud/drywall construction, fi rst cut the hole for the loudspeaker. Then, in the opening, use a drill with a long bit to auger a wire route up or down the wall. Next, cut a hole in the
Summary of the content on the page No. 16
NEW CONSTRUCTION: INSTALLING A BRACKET The hole-saving bracket enables a faster and cleaner fi nal installation of the loudspeaker. It forces the drywall installer to cut out the loudspeaker hole for you and provides wire ties for the loud- speaker wire, reducing the risks of accidental loss or movement of the wire. In addition, it enables you to align your loudspeakers with other ceiling fi xtures with greater accuracy, since you can see exactly where the loudspeaker will be. INSTALLING THE BR
Summary of the content on the page No. 17
CONCEALING LOUDSPEAKER WIRE FOR A FUTURE INSTALLATION 1. Attac h the loudspeaker wire in a loop between the wall studs or ceiling joists and carefully mark the exact location of the wire on a set of plans. 2. Ask the gener al contractor to inform the drywall installers that the loudspeaker wire loops are concealed for future installations, as shown in Figure 12. Figure 12. The loudspeaker wire is looped and hung on two nails attached to the joists, securing it for future use. Be s
Summary of the content on the page No. 18
EXISTING CONSTRUCTION: INSTALLING A BRACKET (CONTINUED) 4. Continue turning the coat hanger as you move it into the cavity to a depth of approxi- mately 4 inches. If you feel an obstruction, fill the hole(s) with spackling compound and repeat steps 1 through 4 at a new location. 5. If the coat hanger moves freely in a complete circle, hold the supplied template up to the wall or ceiling and level it in the horizontal or vertical position. Use a pencil to outline the cutout on the sur
Summary of the content on the page No. 19
FINISHING THE INSTALLATION PAINTING THE GRILLE AND FRAME After drywall is up, each HDFX frame and grille may be painted without the need for primer. For best results, use a spray gun or airless sprayer, thin the paint to prevent clogging of the grille holes, and apply several light coats instead of one heavy one. 1. Paint each grille and let it dry before installation. 2. Paint each frame and let it dry before installation. INSTALLING THE FRAME 1. Fill each wall cavity with insulatio
Summary of the content on the page No. 20
CONNECTING AND INSTALLING THE LOUDSPEAKER 1. At each loudspeaker, separate the loudspeaker wire so that at least 2 inches of each conductor are free. Strip away 1/4 inch of insulation from each loudspeaker wire. 2. On each set of loudspeaker connectors, press down the spring-loaded lever, insert the appropriate conductor, and then release the lever, as shown in Figure 15. Gently tug on the loudspeaker wire to make sure it is held in place. If not, repeat this procedure until it is.
