Summary of the content on the page No. 1
operation manual
SW-150
Miller & Kreisel Sound Corporation
9351 Deering Avenue
Chatsworth, CA 91311-5858
(818) 701-7010 fax (818) 701-0369
www.mksound.com
©2001 Miller & Kreisel Sound Corp.
frameless in-wall speaker
Summary of the content on the page No. 2
In-wall Operation Manual Table of Contents 1. Introduction ...................................................................................................3 Figure 1 - Major Components of the SW-150 .........................................3 2. Speaker Hookup .................................................................................................4 Figure 2 - SW-150 Rear View ...................................................................4 3. Application ..........................
Summary of the content on the page No. 3
In-wall Operation Manual 1. INTRODUCTION Congratulations! Your new M&K in-wall speaker system will give you years of unmatched enjoyment and excitement while listening to your favorite musical and audio/video sources. We encourage you to read this owner’s manual, as there is a great deal of information provided here to help you achieve the best possible performance. If you have any questions about your in-wall speaker system, please contact your M&K dealer or call the M&K factory directly at (81
Summary of the content on the page No. 4
In-wall Operation Manual 2. HOOKUP The Positive (+) lead from your amplifier or receiver should be connected to the RED (+) INPUT terminal, and the Negative (-) lead from your amplifier or receiver should be connected to the BLACK (-) INPUT terminal. 3. APPLICATIONS Left, Center, and Right Channel Speaker for high performance multichannel speaker systems. Left Surround, Right Surround, and Back Surround Channel Speakers for high-performance multichannel systems. Especially well-suited for use as
Summary of the content on the page No. 5
In-wall Operation Manual 4. POST CONSTRUCTION INSTALLATION IMPORTANT! - MAKE SURE WALL ELECTRICITY IS ! ! TURNED OFF BEFORE STARTING INSTALLATION 1. Mark wall with the template, using a 2. Cut opening precisely with a drywall stud finder to maintain a 2” distance from saw, drywall router, etc. Sand edges and any stud. Make sure that you are clear of clean debris from installation area. any crossbraces in the wall structure. FOR STANDARD INSTALLATION DRYWALL THICKNESS CANNOT EXCEED 1.25 INCHES. F
Summary of the content on the page No. 6
In-wall Operation Manual 5. Speaker Mounting wall opening mounting arms speaker wire mounting screws (6 total) 9. Remove packing material and grille from speaker. Do 10. Angle the speaker toward the wall and slip the Not Remove the Elastic Cord! Make sure that the bottom portion of the mounting arms into the wall mounting screws are flush with the front baffle as shown. opening. wall opening 11. Tip the unit vertically and pass the top edge of the 12. Center the speaker within the wall opening.
Summary of the content on the page No. 7
In-wall Operation Manual 13. Make sure that the baffle is level by checking with a 14. Tighten all mounting screws sequentially to light leveling device. resistance. Continue to tighten screws to an even torque that will secure the baffle to the wall. 15. The grille ca be painted with Latex paint to match the 16. Attach the grille. Make sure that the grille is wall color if desired. Make sure that the paint is thin securely mounted on the magnets by tapping on it’s enough and applied carefully s
Summary of the content on the page No. 8
In-wall Operation Manual IMPORTANT! - MAKE SURE WALL ELECTRICITY IS 6. Pre-Construction Installation ! ! TURNED OFF BEFORE STARTING INSTALLATION staples 1. Attach the mounting strips to the pre-construction 2. Attach the bracket assembly to the wall studs with screws or nails (not included). bracket with the included sheet metal screws. 3. Run the speaker wire to the location of the bracket. Secure the wire to one of the studs using staples or “U” nails. Make sure that the wire is clear of the o
Summary of the content on the page No. 9
In-wall Operation Manual 8. SPEAKER DAMAGE & HOW TO AVOID IT An important factor to consider with any loudspeaker system is the potential for speaker damage. Even though your M&K Speakers have extremely high power handling ability (especially for Main speakers), they still can be damaged by relatively low powered amplifiers. While very few M&K Speakers are actually returned for service, the vast majority of those returned are not for manufacturing defects. Instead, they are returned because they
Summary of the content on the page No. 10
In-wall Operation Manual 11 SPECIFICATIONS IMPEDANCE: 4 ohms MINIMUM POWER: 25 watts RMS RECOMMENDED POWER: amplifiers with between 25 and 400 watts RMS MAXIMUM POWER: 400 watts RMS unclipped peaks FREQUENCY RESPONSE: 77 Hz - 20 KHz ± 2 dB SENSITIVITY (2.83 V @ 1m): 92dB FRONT BAFFLE: 11 gauge steel GRILLE DIMENSION (H x W x D): 12.40” x 10.71” x 0.39” BAFFLE DIMENSION (H x W): 12.14” x 10.45” CUTOUT DIMENSION (H x W): 11.25” x 9.875” MOUNTING DEPTH: 3.16” Grille (Front View) SW-150 Baffle (Fr
Summary of the content on the page No. 11
In-wall Operation Manual 11
Summary of the content on the page No. 12
SW150 MANUAL PN # 70076 07/26/01 pt qrk4.11
