Summary of the content on the page No. 1
C200 TWO-WY a
LOUDSpeaker
USer’S manUaL
C200
Summary of the content on the page No. 2
SaFeTY InSTrUCTIOnS 9. Servicing — The user should not attempt toser vice this Mackie 1. Read Instructions —All the safety andoperation instructions should be productbeyond thosemeans described in this operating manual. All other readbefore this Mackie product is operated. servicingshould be refer red to theMackie Service Department. 2. Retain Instructions — The safety andoperating instructionsshould be 10. Exposureto extremely high nois
Summary of the content on the page No. 3
INTRODUCTION Thank you for choosing the Mackie C 00 The.Crossover sound reinforcement loudspeakers. This unique Low Impedance Compensat- The C 00 is a portable two-way loud- ed Crossover (LICC) design places inductors speaker system, specifically designed to in series with the woofer whose values are complement our PPM Series line of profes- markedly lower than conventional designs. sional powered mixers. They are capable of This reduces the amount of energy that is extremely high soun
Summary of the content on the page No. 4
HOOKUP.DIAGRAMS . Turn on your mixing console (or other Quick.Start signal source). Make all initial connec- 4. Turn on the amplifier. Turn up its vol- tions with the power ume or gain control(s) as recommended switches OFF on all by the manufacturer. equipment. Make sure all 5. Start the signal source, whether it be master volume, level, or speaking into a microphone or starting gain controls are all the way down. a CD player. Adjust the volume controls 1. Connect the line-level out
Summary of the content on the page No. 5
SERIAL NUMBER MANUFACTURING DATE SERIAL NUMBER MANUFACTURING DATE SERIAL NUMBER MANUFACTURING DATE SERIAL NUMBER MANUFACTURING DATE DESIGNED BY MACKOIDS IN WHITINSVILLE, MA AND WOODINVILLE, WA, USA DESIGNED BY MACKOIDS IN WHITINSVILLE, MA AND WOODINVILLE, WA, USA DESIGNED BY MACKOIDS IN WHITINSVILLE, MA AND WOODINVILLE, WA, USA DESIGNED BY MACKOIDS IN WHITINSVILLE, MA AND WOODINVILLE, WA, USA MANUFACTURED IN CHINA • FABRIQUE AU CHINE • COPYRIGHT ©2003 MANUFACTURED IN CHINA • FABRIQUE AU CHINE •
Summary of the content on the page No. 6
CONNECTIONS The 1/4˝ TS jack is wired as follows: The C 00 has 1/4˝ TS and Speakon™- Tip = Signal (“+” or hot) style INPUT and THRU connectors. The Sleeve = Ground (“–” or cold) connectors are wired in parallel, so use only SLEEVE SLEEVE TIP one of the input connectors (either 1/4˝ TS or Speakon-style). TIP TIP ("+" or HOT) SLEEVE ("–" or COLD) 1/4˝ TS Connector INPUT THRU PARALLEL The Speakon-style connector is wired as follows: Pin 1+ = Signal (“+” or hot) Pin 1– = Ground (“–” or col
Summary of the content on the page No. 7
walls, ceiling, and floor play havoc with Room.Acoustics the sound. Depending on the situation, The C 00 loudspeakers are designed you may be able to take some steps to to sound as neutral as possible; that is, to minimize the reflections, such as putting reproduce the input signal as accurately as carpeting on the floors, closing draperies possible, monitoring the audio signal rather to cover large glass windows, or hanging than changing it. tapestries or other materials on the walls
Summary of the content on the page No. 8
SERVICE.INFO If you think your Mackie product has a It.hurts.when.I.touch.my.arm,.or.my.leg,.or. problem, please check out the following even.my.head! troubleshooting tips and do your best to • You have a broken finger. confirm the problem. Visit the Support section of our website (www.mackie.com/ Bad.sound! support) where you will find lots of use- • Is it loud and distorted? Follow the pro- ful information such as FAQs, documen- cedures described in the “Quick Start” tation, and user foru
Summary of the content on the page No. 9
CARE.AND. MAINTENANCE Your Mackie loudspeakers will provide many years of reliable service if you follow these simple guidelines: • Avoid exposing the loudspeakers to moisture. If they are set up outdoors, be sure they are under cover if you expect rain. • Avoid exposure to extreme cold (below freezing temperatures). If you must operate the loudspeakers in a cold envi- ronment, warm up the voice coils slowly by sending a low-level signal through them for about 15 minutes prior to high-
Summary of the content on the page No. 10
C200.SPECIFICATIONS System Specifications Safety Features Frequency Response (–3 dB) Driver Protection 89 Hz – 0 kHz Dynamic protection for compression driver Frequency Range (–10 dB) Construction Features 59 Hz – kHz Maximum SPL Long-term @ 1m 118 dB Basic Design Asymmetrical Trapezoidal Low-Frequency Crossover Type Material Polypropylene dB/octave, time offset corrected Finish Grey, textured finish High-Frequency Crossover Type Handles One on left side, one
Summary of the content on the page No. 11
C200.LIMITED.WARRANTY Please keep your sales receipt in a safe place. IMPORTANT: Make sure that the Service Request Number A. LOUD Technologies Inc. warrants all materials, workman- is plainly written on the shipping carton. No receipt, no war- ship and proper operation of this product for a period of one ranty service. year from the original date of purchase. You may purchase an additional 24-month Extended Warranty (for a total of 36 E. LOUD Technologies reserves the rig
Summary of the content on the page No. 12
LOUD Technologies Inc. 16220 Wood-Red Road NE • Woodinville, WA 98072 • USA US and Canada: 800.258.6883 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.com 1
