Summary of the content on the page No. 1
S7012
Version 1.1
Copyright
®
Copyright © 2009 MiTAC International Corporation. All rights reserved. TYAN is a
registered trademark of MiTAC International Corporation.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
®
TYAN is a trademark of MiTAC International Corporation.
®
Intel Nehalem-EP Series and combinations thereof are trademarks
Summary of the content on the page No. 2
Table of Contents Check the box contents! 3 Chapter 1: Introduction 1.1 Congratulations 5 1.2 Hardware Specifications 5 1.3 AST2050 Application 6 Chapter 2: Board Installation 2.1 Board Image 8 2.2 Block Diagram 9 2.3 Board Parts, Jumpers and Connectors 10 2.4 Installing the Processor and Heatsink 20 2.5 Thermal Interface Material 23 2.6 Finishing Installing the Heatsink 24 2.7 Tips on Installing Motherboard in Chassis 25 2.8 Installing the Memory 26 2.9 Attaching Drive Cables
Summary of the content on the page No. 3
Check the box contents! 1x S7012 motherboard 2 x mini SAS Cable (optional) 6 x Serial ATA Cable 1 x USB2.0 cable 1 x S7012 User’s Manual 1 x S7012 Quick Reference Guide 1 x I/O Shield Installation Guide 1 x TYAN Installation CD 1 x I/O shield If any of these items are missing, please contact your vendor/dealer for replacement before continuing with the installation process. 3 http://www.tyan.com
Summary of the content on the page No. 4
NOTE 4 http://www.tyan.com
Summary of the content on the page No. 5
Chapter 1: Introduction 1.1 - Congratulations ® You have purchased one of the most powerful server solutions. Based on Intel 5520 and ICH10R chipsets, the S7012 is designed to support up to two Nehalem- EP Series processors and up to 144GB DDR3-800/1033/1066/1333 memory, providing a rich feature set and incredible performance. Leveraging advanced technology from Intel, the S7012 is capable of offering scalable 32 and 64-bit computing, high-bandwidth memory design, and lightning-fast PC
Summary of the content on the page No. 6
Resolution 1600x1200@60Hz Chipset Aspeed AST2050 USB (7) USB2.0 ports (4 at rear, 2 via cable, 1 type A onboard) COM (1) port (rear) SAS (2) Mini-SAS (4-in-1) connectors VGA (1) D-Sub 15-pin VGA port Input /Output RJ-45 (4) GbE ports Power SSI 24-pin + 8-pin + 8-pin power connectors / EPS12V Front Panel (1) 2x12-pin SSI front panel header SATA (6) SATA-II connectors Chipset Winbond W83793G Voltage Monitors voltage for CPU, memory, chipset & power supply System Fan Total (5) 4-pin
Summary of the content on the page No. 7
Chapter 2: Board Installation You are now ready to install your motherboard. The mounting hole pattern of the S7012 matches the SSI EEB specification. Before continuing with installation, confirm that your chassis supports an SSI EEB motherboard. How to install our products right… the first time The first thing you should do is reading this user’s manual. It contains important information that will make configuration and setup much easier. Here are some precautions you should take
Summary of the content on the page No. 8
2.1- Board Image S7012 This picture is representative of the latest board revision available at the time of publishing. The board you receive may or may not look exactly like the above picture. 8 http://www.tyan.com
Summary of the content on the page No. 9
2.2 - Block Diagram S7012 9 http://www.tyan.com
Summary of the content on the page No. 10
2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. Jumper Legend OPEN - Jumper OFF, without jumper cover CLOSED – Jumper ON, with jumper cover 10 http://www.tyan.com
Summary of the content on the page No. 11
Jumper/Connector Function J9 (TYFP1) Standard Front Panel Connector 2 J16 BMC I C Bus Header J34 USB Front Panel Header (blue) J18 COM2 Connector J24 PSMI Connector J6 Chassis Intrusion Header J35 CPLD JTAG Header USB3 Type-A USB Connector J33 ICH SGPIO Header J15 Port 80 Header J41/J42/J43/J44/J45 8-pin 4056 Fan Connector (reserved for BB) J2/J8/J36/J37/J38 4-pin Fan Connector J39/J40 Reset Switch/Power Switch LSI 1068E Enable/Disable Jumper J3 Pin 1-2 closed: Enable (Default)
Summary of the content on the page No. 12
(From left to right) SATA5/SATA4/SATA3/SATA2/SATA1/SATA0 J16 J18 J15 J34 12 http://www.tyan.com
Summary of the content on the page No. 13
J18: COM2 Connector Pin Signal Pin Signal 10 2 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 9 7 DTR 8 RI 1 9 GND 10 KEY J15: PORT 80 Header Pin Signal Pin Signal 1 NC 2 V3P3 2 14 3 NC 4 FRAME 5 CLK_33M 6 GND 7 GND 8 LAD3 1 13 9 PLTRST 10 LAD2 11 NC 12 LAD1 13 NC 14 LAD0 2 J16: BMC I C Header 1 PinSignal Pin Signal 1 IPMB_DAT 2 GND 3 IPMB_CLK 4 NC J34: USB Front Panel Header (Blue) Pin Signal Pin Signal 2 10 1 +5V 2 +5V 3 USB D- 4 USB D- 5 USB D+ 6 USB D+ 1 9
Summary of the content on the page No. 14
J38 J8 J24 J45 J2 J44 J43 J42 J37 J36 J9 J41 J6 J6: Chassis Intrusion Header PinSignal PinSignal 1 INTRUDER# 2 GND 1 14 http://www.tyan.com
Summary of the content on the page No. 15
J9 (TYFP1): Standard Front Panel Connector 24 2 23 1 PIN1 PIN3 PIN5 PIN7 PWRLED+ KEY PWRLED- HDLED+ PIN2 PIN4 PIN6 PIN8 +5VSB IDLED+ IDLED- WLED- PIN9 PIN11 PIN13 PIN15 HDLED- PWRSW+ GND RSTSW PIN10 PIN12 PIN14 PIN16 PSI_BMC_R- LAN1LED+ LAN1LED- SMBDAT PIN17 PIN19 PIN21 PIN23 GND IDLED_SW TEMP-SENSORNMI_SW- PIN18 PIN20 PIN22 PIN24 SMBCLK INTRD# LAN2LED+ LAN2LED- NOTE1: +3.3V power rail is IDLED, WLED (Warning LED), LANLED NOTE2: +5V power rail is PWRLED,
Summary of the content on the page No. 16
JP3 J35 JP2 JP1 USB3 J33 16 http://www.tyan.com
Summary of the content on the page No. 17
USB3: Type-A USB Connector Pin Signal Pin Signal 1 +5V 2 USB D- 3 USB D+ 4 GND J33: ICH SGPIO Header 9 10 Pin Signal Pin Signal 1 SMBCLK 2 SDATAOUT0 3 SMBDAT 4 SDATAOUT1 5 GND 6 SLOAD 7 KEY 8 SCLOCK 9 NC 10 NC 1 2 J35: CPLD JTAG Header 2 10 PinSignal PinSignal 1 JTAG_TCK 2 GND 3 JTAG_TDO 4 +3.3V 5 JTAG_TMS 6 NC 1 9 7 NC 8 KEY 9 JTAG_TDI 10 GND JP3: Clear CMOS Jumper Use this jumper when you forgot your system/setup 1 3 password or need to clear sy
Summary of the content on the page No. 18
J3 J7 J1 18 http://www.tyan.com
Summary of the content on the page No. 19
J7: BMC Reset Jumper Pin 1-2 Open: Enable BMC(Default) 1 Pin 1-2 Closed: Disable BMC 1 J1: LSI 1068E Device ID Select Jumper 1 Pin 1-2 Closed: LSI 1068E Device ID (Default) 3 1 Pin 2-3 Closed: :LSI 1068E Device ID – Device ID bit [0] =0b1 3 J3: LSI 1068E Enable/Disable Jumper 1 3 Pin 1-2 Closed: Enable LSI 1068E (Default) 1 3 Pin 2-3 Closed: Disable LSI 1068E 19 http://www.tyan.com
Summary of the content on the page No. 20
2.4 - Installing the Processor and Heat Sink ® Your S7012 supports the latest processor technologies from Intel . Check the TYAN website for latest processor support: http://www.tyan.com Processor Installation (LGA1366 Socket) The processor should be installed carefully. Make sure you are wearing an antistatic strap and handle the processor as little as possible. Please note that both processors of the same type and frequency are required for optimal system performance. NOTE:
