Summary of the content on the page No. 1
Fixed Dome
FE8174V Network Camera
User’s Manual
5MP • 360º Surround View • Vandal-proof • PoE
Rev. 1.0
Summary of the content on the page No. 2
VIVOTEK Table of Contents Overview 4 Revision History ..............................................................................................................................................4 Read Before Use ....................................
Summary of the content on the page No. 3
VIVOTEK Network > General settings .................................................................................................................................. 69 Network > Streaming protocols .......................................................................................................................... 77 Network > QoS (Quality of Service) .................................................................................................................. 82 Network > DDNS
Summary of the content on the page No. 4
VIVOTEK Overview VIVOTEK FE8174/74V is the latest fisheye fixed dome network camera from VIVOTEK, featur- ing a detailed 5-Megapixel resolution sensor with superb image quality. Equipped with a fisheye lens for 180° panoramic view (wall mount) or 360° surround view (ceiling/floor/table mount) with- out blind spots, the camera is able to provide coverage of wide, open areas, such as airports, shopping malls, parking lots, retail stores, offices and more. The FE8174/74V offers various display
Summary of the content on the page No. 5
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below. Take note of the
Summary of the content on the page No. 6
VIVOTEK Physical Description Inner View ) Contacts for Internal Microphone (B Lens Spring Contacts (A) i Align (B) to (A) when attaching the dome cover Header (J6) Ethernet 10/100 RJ45 Socket Header (J7) Status LEDs Reset Button MicroSD/SDHC/SDXC Card Slot 6 - User's Manual
Summary of the content on the page No. 7
VIVOTEK Outer View IP66-rated Vandal-proof Dome Cover Built-in Microphone IMPORTANT: 4 083236 Record the MAC address under the camera base before installing the camera. Item LED Status Description 1 Steady Red Power on and system booting Red LED off Powered off 2 Steady Red + blinking Green every 1 sec. (Green Network heartbeat LED on for 1 sec and off for another) Steady Red + Green LED off Network disconnected 3 Blinking Red every 0.15 sec. + Blinking Green Upgrading firmware every 1 sec.
Summary of the content on the page No. 8
VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method. GND GND VDC Camera Power VDC Camera Power +12 VDC Switch Switch +12 Input Input VDC Max. Output Output BJT transistor BJT transistor Relay Relay Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, press the reset button longe
Summary of the content on the page No. 9
VIVOTEK Hardware Installation Opening Dome Cover First, use the supplied screwdriver to loosen the four screws and detach the dome cover from the camera base. Then, follow the steps below to install the camera to either a ceiling or a wall. Tamper-proof Screw Remove the stoppers and route cables through the openings. Rubber Stopper on the hole for Power & IO Cables Rubber Seal Plug on the hole for RJ45 Ethernet Cable User's Manual - 9
Summary of the content on the page No. 10
VIVOTEK Connecting RJ45 Ethernet Cable 1 RJ45 Cable Dimension (unit: mm) Rubber Seal Plug Recommended cable gauge: 5 to 8mm Assembly Steps 1. Drill a hole on the rubber seal plug and insert an Ethernet cable through the opening. 2. Strip part of the sheath from the Ether- net cable. 2 3 3. You will need an RJ45 crimping tool to attach the Ethernet wires to a connec- o: white/orange stripe tor. When done, connect the cable to o O: orange solid 1 O 2 the camera’s Ethernet RJ45 socket. g: whi
Summary of the content on the page No. 11
VIVOTEK Mounting Positions Refer to the diagram on the right for the mounting hole positions and the dimensions of the base plate. Camera Base Plate Mounting Positions Camera Mounting Plate Mounting Positions User's Manual - 11
Summary of the content on the page No. 12
VIVOTEK Ceiling/Wall Mount without Mounting Plate (Choose this mounting type if you want to feed the cables form the bottom of the camera) 1. Attach the supplied alignment sticker for camera base to the ceiling/wall. 2. Using the three circles on the sticker, drill three pilot holes into the ceiling. Then hammer the three supplied plastic anchors into the holes. 3. Drill a cable hole on the ceiling/wall, and feed the cables through the hole. 4. Connect the Ethernet cable to the socket. 5. Co
Summary of the content on the page No. 13
VIVOTEK Ceiling/Wall Mount with Mounting Plate (Choose this mounting type if you would like to feed the cables form the side) 1. Attach the supplied alignment sticker for the supplied mounting plate to the ceiling/wall. 2. Using the three circles on the sticker, drill three holes into the ceiling. Then hammer the three supplied plastic anchors into the holes. 3. Arrange and feed the cables through the side of the mounting plate. 4. Secure the mounting plate to the ceiling/wall with three supp
Summary of the content on the page No. 14
VIVOTEK You may also use the diagonal holes on the mounting plate, marked as A, B, or C, to install the camera to a U.S. standard 4 in. junction box. 14 - User's Manual
Summary of the content on the page No. 15
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet There are several ways to set up the Network Camera over the Internet. The first way is to set up the Network Camera behind a router. The second way is to utilize a static IP. The third way is to use PPPoE. Internet connection via a router Before enabling the access to the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. C
Summary of the content on the page No. 16
VIVOTEK For example, your router and IP settings may look like this: Device IP Address: internal IP Address: External Port (Mapped port on the port router) Public IP of router 122.146.57.120 LAN IP of router 192.168.2.1 Camera 1 192.168.2.10:80 122.146.57.120:8000 Camera 2 192.168.2.11:80 122.146.57.120:8001 ... ... ... Configure the router, virtual server or firewall, so that the router can forward any data coming into a preconfigured port number to a network camera on the private network,
Summary of the content on the page No. 17
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection with static IP Choose this connection type if you are required to use a static IP for the Network Camera. Please refer to LAN configuration on page 69 for details. Internet connection via PPPoE (Point-to-Point over Ethernet) Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to PPPoE on page 90 for details. Set up the Network
Summary of the content on the page No. 18
PARTITION I LNK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK General Connection (without PoE) 1. If you have external DI devices, make the connection from general I/O terminal block. 2. Ethernet, power and IO cables are user-supplied. 3. Connect DC power cord to a DC Adapter, and then to a power outlet. 1 3 +3V3 : Power, 3.3V DC +3V3 DO : Digital Output DO DI : Digital Input D1 GND : Ground GND 2 General I/O Terminal Block Power Cord Socket (Black) Microphone In (Pink) Audio Out (Green) NOTE: Th
Summary of the content on the page No. 19
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN. IW2 1. Install IW2 under the Software Utility directory from the software CD. Double click the IW2 shortcut on your desktop to launch the program. Installation Wizard 2 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3. T
Summary of the content on the page No. 20
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. NOTE: If you encounter problems with displaying live view or the onscreen plug-in control, you may try to remove the plug-ins that might have been i
