Summary of the content on the page No. 1
SNC-C6225
SNC-C7225
10x Network Mini Smart
Dome Camera
User Manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
Please visit our website.
www.samsungsecurity.com
Summary of the content on the page No. 2
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accomp
Summary of the content on the page No. 3
safety information 12. Do not expose the product to the direct airfl ow from an air conditioner. Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera. 13. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not fl ow inside the housing. Otherwise, external high, humid air may fl ow inside the housing, pool
Summary of the content on the page No. 4
important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of the polarized o
Summary of the content on the page No. 5
contents Introduction Features 7 Recommended PC Specifi cations 8 Compatible IP Routers 8 Product & Accessories 9 Parts Name & Functions 11 Installation DIP Switch Setup 13 Installation Using Surface Mount On The Ceiling 14 Installation Using Ceiling Mount Bracket 15 Installation Using Wall Mount Bracket 16 Cabling 17 Inserting/Removing an micro SDHC Memory Card 19 Memory Card Information (not included) 20 Operation Check points before operation 21 Prese
Summary of the content on the page No. 6
contents Network connection & Setup Connecting the camera to an IP router with the xDSL/Cable modem 39 Connecting the camera to an IP router with local area networking 41 Connecting the camera directly to a DHCP-based xDSL/Cable modem 43 Connecting the camera directly to local area networking 44 Searching for the camera 45 Setting Static IP Manual Network Setting 46 Automatic Network Setting 48 Setting Dynamic IP Dynamic IP Setting 49 Port Forwarding (Port Mapping) Se
Summary of the content on the page No. 7
introduction � Max. 8 set of Auto Pan can be stored. This enables FEATURES to move camera repetitively between two preset positions with designated speed. ❖ Network Specifi cations � Max. 4 of Patterns can be recorded and played back. � Powerful Dual Stream by using DSP based This enables to move camera to follow any trajectory MPEG4, MJPEG compression operated by joystick as closely as possible. � Superior Video Quality and System Stability. � Max. 8 set of Scan action can be stored. � Hig
Summary of the content on the page No. 8
introduction RECOMMENDED PC SPECIFICATIONS � CPU : Pentium4/2.4GHz or higher � Operating System : Windows XP(Service Pack 2) / Windows Vista � Resolution : 1024x768 pixels or higher � RAM : 512MB or higher � Web Browser : Internet Explorer 6.0 or higher � Video Card : Radeon, Nvidia � Video Memory : 128MB � DirectX 8.1 or higher COMPATIBLE IP ROUTERS � Linksys � D-Link � Netgear 8 – 10x Network Mini Smart Dome Camera
Summary of the content on the page No. 9
introduction PRODUCT & ACCESSORIES ❖ SNC-C6225 • Product Main Body Surface Mount Bracket • Accessories Terminal Block Torx Screw Driver Surface Mount Gasket Screw & Plastic Anchor (4pcs) Quick Guide Audio Cable User Manual / IP Installer CD Cross Cable Core Filter Mount Bracket Option : Please use SADT-937WM for this purpose. M English – 9
Summary of the content on the page No. 10
introduction ❖ SNC-C7225 • Product Main Body Sun Shield Housing • Accessories Terminal Block Torx Screw Driver Audio Cable Cross cable Quick Guide User Manual / IP Installer CD Core Filter • Mount Bracket Option Wall Mount Bracket Ceiling Mount Bracket (SADT-732WM) (SADT-732CM) 10 – 10x Network Mini Smart Dome Camera
Summary of the content on the page No. 11
introduction PARTS NAME & FUNCTIONS ❖ SNC-C6225 Surface Mount Bracket Mounting Hole Main Body Cabling Terminal Block Lockup Screw DIP Switch Dome Cover Main Unit / Surface Mount Bracket Back of Main Unit • Dome Cover • Lockup Screw Do not remove the protection vinyl from dome cover Fixes main unit brackets like surface, wall, and ceiling. before fi nishing all installation process to protect dome cover from scratches or dust. • Cabling Terminal Block During installation, Power, Video, Commun
Summary of the content on the page No. 12
introduction ❖ SNC-C7225 Sun Shield Housing Cabling Terminal Block Main Body Lockup Screw DIP Switch Dome Cover Main Unit / Sun Shield Housing Back of Main Unit • Dome Cover • Cabling Terminal Block Do not remove the protection vinyl from dome cover During installation, Power, Video, Communication, before fi nishing all installation process to protect dome Alarm Input cables are connected on to this cabling cover from scratches or dust. terminal block. • Sun Shield Housing • DIP Switch Ad
Summary of the content on the page No. 13
Installation ❖ Communication Protocol Setup DIP SWITCH SETUP Before you install the camera, you should set the DIP ON ON switches to confi gure the camera ID, Baud Rate and communication protocol. 12 3 4 56 78 Protocol Baud Rate 0x00 : Auto Protocol 0x00 : 2400 � Select the appropriate Protocol with DIP switch 0x03 : SAMSUNG 0x01 : 4800 combination. 0x02 : 9600 Switch State 0x03 : 19200 Protocol Pin1 Pin2 Pin3 Pin4 0x04 : 38400 OFF OFF OFF OFF Auto Protocol ON ON OFF OFF SAMSUNG RS-
Summary of the content on the page No. 14
installation ❖ RS-485 Termination Resistor 3. Wire cables to terminal block and connect the terminal blocks to main unit. ON ON 12 3 4 56 78 � Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera. – Pin 8 : RS-485 Termination Resistor (ON/OFF) INSTALLATION USING SURFACE MOUNT ON THE CEILING 4. Screw main unit to surface mount bracket with 4 loc
Summary of the content on the page No. 15
installation 3. After wiring cables to terminals, plug the terminals INSTALLATION USING CEILING into the bottom of main unit. Then, fi x the main MOUNT BRACKET unit with sunshield with 4 screws. ❖ SNC-C7225 1. Install ceiling mount bracket on the ceiling using 4 screws provided. 2. Turn sunshield clockwise after locating it in the 4. Detach protection vinyl from dome cover. pipe head of ceiling mount properly. English – 15
Summary of the content on the page No. 16
installation 3. After wiring cables to terminals, plug the terminals INSTALLATION USING WALL into the bottom of main unit. Then, fi x the main MOUNT BRACKET unit with sunshield with 4 screws. ❖ SNC-C7225 1. Use the 4 screws (provided) to secure the wall mount bracket to the wall. 2. Turn sunshield clockwise after locating it in the pipe head of wall mount properly. 4. Detach protection vinyl from dome cover. 16 – 10x Network Mini Smart Dome Camera
Summary of the content on the page No. 17
installation CABLING ❖ SNC-C6225/SNC-C7225 Audio In Microphone Audio Out Speaker DC 12V IrDA Sensor Controller/DVR Door Switch Sensors BNC Video Lamp Relay Out Network ❖ Power Connection � Please, check the voltage and current capacity of rated power carefully. Power Consumption Rated Power Input Voltage Range SNC-C6225 SNC-C7225 15W(Heater Off) / DC 12V DC 11V ~ 15V 15W 25W(Heater On) ❖ RS-485 Communication � For PTZ control, connect this line to keyboard and DVR. To control multiple cameras
Summary of the content on the page No. 18
installation ❖ Video Connection � Connect with BNC coaxial cable. ❖ Audio Input/Ouput Connection 1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifi er that the microphone is connected to direct Mic Connection: Set Audio Input Gain high (10). Line Out Connection: Set Audio Input Gain low (1). Refer to page 58 in this Manual. 2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker. If the microphone is connected directly
Summary of the content on the page No. 19
installation INSERTING/REMOVING AN MICRO SDHC MEMORY CARD ❖ Inserting an Micro SDHC Memory Card � Push the Micro SDHC memory card in the direction of the arrow shown in the diagram. Do not force the memory card in. If you can’t insert the memory card into the slot with ease, you might be inserting the card in J the wrong direction. Forcibly inserting a memory card could lead to its damage. ❖ Removing an Micro SDHC Memory Card � Gently press down on the exposed end of the memory card as show
Summary of the content on the page No. 20
installation MEMORY CARD INFORMATION (NOT INCLUDED) ❖ What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. ❖ Selecting a memory card that’s suitable for you Your camera supports Micro SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. Your camera supports Micro SD memory cards. Howev
