Summary of the content on the page No. 1
CCD COLOR CAMERA
BDC4803VFD
USER MANUAL
Page : 1
Summary of the content on the page No. 2
CONTE CONTENTSbbbbbbbbbbbbbbbb NTS bbbbbbbbbbbbbbbbbbbb - PRECAUTIONS……………………………………… Page 3 - PACKING CONTENTS...…………………………… Page 4 - 1. User Manual………………………..........……………… Page 4 - 2. Camera……………...……..............................………… Page 4 - 3. Adapter Cable…………….............................………… Page 4 - 4. Screws……………...……..............................………… Page 4 - FEATURES AND FUNCTIONS………………….… Page 5 - INSTALLATION…………………………………...… Page 6 - 1. Power connection
Summary of the content on the page No. 3
PRECAUTIONS PRECAUTIONS 1. Do not attempt to disassemble the camera. There are no user serviceable parts inside. Ask a qualified service person for servicing 2. Handle the camera with care. Do not misshandle the camera. Avoid striking, shaking, etc. Improper handling or storage could damage the camera. 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera.
Summary of the content on the page No. 4
P PACKING CONTE ACKING CONTEN NT TS S 1. Usermanual 2. Camera 3. Adapter Cable 4. Screws 2 x Fixing Screws Page : 4
Summary of the content on the page No. 5
FEATURES AND FUNCTIONS F - Auto Light Control (ALC) function - Electronic Light Control (ELC) function - Automatic Gain Control (AGC) function - Automatic Tracing White Balance (ATW) function - Internal Synchronisation - Minimum Illumination of 1 Lux @ F2.0 - Signal to noise ratio > 45 dB (AGC off) - Horizontal resolution of 480 TV lines. - OLPF Built in Unlike usual cameras, this camera filters unnecessary noise signals in dark view and transmits them with more clear picture signals. This mak
Summary of the content on the page No. 6
INSTALLATION I 1. Power connection Connect the DC 12V powercable with the + 12V- and GND Terminal. Power– and Signal Terminal camera bottom + 12V = +12V DC (10%) GND = GND - Power + CVBS Shield CVBS = CVBS Signal NC = No Connection In addition to use the screw terminal you can connect the Adapter cable to this terminal and then you can connect power by NES Plug and the video signal by BNC Plug. Page : 6
Summary of the content on the page No. 7
Resistance of copper wire (at 20 °C) Copper 0,22 mm² 0,33 mm² 0,52 mm² 0,83 mm² wire size 0,078 0,05 0,03 0,018 / m Calculation of max. cable length between camera and power supply: 10,5V DC V – (R x 0,42 x L) 16V DC L : Cable length (m) R : Resistance of copper wire ( / m) V : DC output voltage of power supply (V DC) L standard = V - 12 / 0,42 x R L min. = V - 16 / 0,42 x R L max. = V - 10,5 / 0,42 x R Page : 7
Summary of the content on the page No. 8
2. Video cable It is recommended to use a monitor with a resolution at least equal to that of the camera. Connect the Video cable with the CVBS and GND Terminal. Power– and Signal Terminal camera bottom + 12V = +12V DC (10%) GND = GND - Power + CVBS Shield CVBS = CVBS Signal NC = No Connection In addition to use the screw terminal you can connect the Adapter cable to this terminal and then you can connect power by NES Plug and the video signal by BNC Plug. Page : 8
Summary of the content on the page No. 9
The max. extensible coaxial cable length between camera and the monitor is shown below. Coax cable type RG-59/U RG-6U RG-11/U RG-15/U (3C-2V) (5C-2V) (7C-2V) (10C-2V) Recommended max. cable length (m) 250 500 600 800 Page : 9
Summary of the content on the page No. 10
3. View angle and focus Adjustment Open the Dome Cover to adjust the angle of view (Zoom) and focus Zoom and Focus Adjustment To adjust focus and the viewing angle (Zoom) you have to loosen the adjustment lever by turning left, afterwards you can slide the adjustment lever right and left. Adjust at first the viewing angle and afterwards the focus to get a sharp picture. After adjustment fix the adjustment lever by turning right. Min. – max. viewing angle Max. W (Wide) Max. T (Tele) 4 mm 8 mm
Summary of the content on the page No. 11
SPECIFICATION S Model Name BDC4803VFD Signal Standard PAL Objective f : 4 – 8 mm CCD – Chip 1/3” Super HAD CCD Scanning System 2:1 Interlaced Scanning Frequency H: 15.625 kHz V: 50 Hz Total Pixels 795 (H) x 596 (V) app. 470.000 Pixel Effective Pixels 752 (H) x 582 (V) app. 440.000 Pixel Horizontal Resolution 480 Lines Electronic Shutter 1/50 – 1/100000 auto Automatic Iris Control Yes S/N Ratio > 45 dB (AGC off) Sensitivity 1.0 Lux @ F 2.0 Sync System Internal Sync White Balance A
Summary of the content on the page No. 12
ADDRESS (Technical specifications subject to change. No liability will be assumed for printing errors or other errors.) Page : 12
