Summary of the content on the page No. 1
IP camera
CAM77IP LAN-controlled IP camera
Summary of the content on the page No. 2
IP camera Disclaimer • We spared no efforts to make sure that the information in this manual is correct and complete. However no liability is accepted for any errors or omissions. Gembird Electronics reserves the right to change the specifications of the hardware and software described in this manual without prior notice. • No part of this manual may be reproduced, transmitted or translated in any language in any form, by any means, without the prior written permission of Gembird E
Summary of the content on the page No. 3
IP camera CAM77IP User manual Introduction Thank you for buying the Gembird® LAN-controlled IP camera with MJPEG recording, motion detection, flash-card and night-vision support! This manual will help you install and use it properly. CAM77IP is an affordable and efficient remote monitoring-managing surveillance solution. Simple installation, internal Web server, can be accessed any time - any places. CAM77IP capable of directly connected to local and broadband network. Usi
Summary of the content on the page No. 4
IP camera Features • Remote controlled via Ethernet network (RJ45 connector) • Accessible via HTTP, FTP protocols, sends records by E-mail (SMTP), supports static IP, DHCP, PPPoE, DDNS, NTP (Network Time) protocols • Supports recording using MJPEG coding • Supports storage to SD flash cards • Supports motion detection function • Supports night vision by means of the infrared LEDs Specification • Resolution: 160x120, 320x240 and 640x480 pixels • Image quality: Fine, Norm
Summary of the content on the page No. 5
IP camera Package contents • IP camera with base • Power adaptor with 1.4m cable • Driver and software CD • 2m LAN cable System requirements • CPU: 1.6GHz or above • Operating system: Windows 2000/XP or above • Memory: 128MB or above (recommended 256MB) • Browser: Microsoft IE6.0 or above • Hard drive: at least 10MB disk space
Summary of the content on the page No. 6
IP camera Hardware Descriptions and Connection Product Bottom Figure 1. CAM77IP Network Camera Bottom View SW1: Hardware Rest SW2: Press to restore factory default IP Address (192.168.1.100) (Press and hold more than 5 seconds)
Summary of the content on the page No. 7
IP camera Bottom Front Lens Lens cover Status LED Infrared LED Figure 2. CAM77IP Network Camera Front View
Summary of the content on the page No. 8
IP camera Connectors Figure 3. CAM77IP Network Camera rear view SD Storage Card Figure 4. SD Storage Card
Summary of the content on the page No. 9
IP camera Installation and configurations Hardware Installation Ethernet Power Figure 5. Installation diagram • Plug the Ethernet cable into the RJ-45 connector at the LAN connector as picture shown. • Plug the other end of the Ethernet cable into any available LAN port. A typical
Summary of the content on the page No. 10
IP camera home router/gateway connection shown as below. • Connect the power supply to the Power connector, and then plug the supply into an available power outlet. • Insert the SD card (optional) into the SD card slot as shown below (figure 6). Figure 6. Insertion of SD memory storage card Caution During Power On or while pressing SW1 button; LED(D5) flash for 3 times follow with a short period of light out(about 5 seconds) for system reinitiating process. When sy
Summary of the content on the page No. 11
IP camera CAM_EZ SEARCH Browse the IP camera CD. Execute the d:\Utility\CAM_EZ search program. The CAM_EZ search can be used to manually configure the IP camera's network settings. It may be necessary to use this tool assign an IP address for your IP camera if your IP camera network setting need configuration. This tool is also helpful for finding all the cameras on your network. CAM_EZ search also display the IP camera's status and link to Internet Explorer Web control. Note: Th
Summary of the content on the page No. 12
IP camera • Access the CAM77IP setup page via Internet Explorer by double click on "your CAM77IP list" CAM_EZ Search diagram
Summary of the content on the page No. 13
IP camera System Login System login ensure authentication is done to any attempted access to the system. Our system provided 2 level of administrative mode: Administrator and General user. After Login successfully, you should be able to enable network surveillance and camera configuration; Following is the steps to it: 1. To access the System Login, do either of following: • Using CAM_EZ Search, double click on your CAM77IP's name in the update list • Enter the IP a
Summary of the content on the page No. 14
IP camera 2. The System Login pages should shown as below: 3. Enter the Account ID and Password; Default Account ID = "admin", Password = "password". 4. Click Submit Button, then instants capture form camera should be shown, as below.:
Summary of the content on the page No. 15
IP camera Real-time Surveillance While running IPCAM for the first time, "Internet Explore Security Settings" have to be change to view captured image properly; Or else, the following warning message will appear. The "Internet Explore Security Settings" only required to be done once. Internet Explore Security Settings: Change the following setting to enable browsing of web interface, in Internet Explorer by clicking "Tool"=>"Internet Options"=>"Security"=>"Custom Level". 1. Sc
Summary of the content on the page No. 16
IP camera Real-time Snapshot This function enables hotkey to trigger saving captured picture to computer. Step 1. Enter the LiveView menu. Step 2. Place the mouse cursors over the Liveview image, press and hold the "Ctrl" key. Step 3. Right click mouse Step 4. Release "Ctrl" Key, now a single-shot static image is captured. Step 5. Click on CaptureView menu to browse the captured images.
Summary of the content on the page No. 17
IP camera Advanced Function With Liveview Place the mouse cursors over the Liveview image, then right click, list with 4 options will shown as below: * Image: Image configuration adjustment * Record: Record AVI formatted document * Zoom: Zooming the chosen windows * Motion Detect Set: Motion Detect Configuration
Summary of the content on the page No. 18
IP camera Image Adjustment Step 1. Place the mouse cursors over the Liveview image. Step 2. Rght click and choose image on the menu, change the image control value, as below: AVI Record Setup Step 1. Place the mouse cursors over the Liveview image. Step 2. right click and choose image on the menu, adjust the AVI Frame Rate and document name, click "START" button to start recording, and "STOP" button to stop recording.
Summary of the content on the page No. 19
IP camera Zoom in Display Step 1. Place the mouse cursor over the Liveview image. Step 2. Right click and choose Zoom on the menu Step 3. Use cursor to box the area to be zoom, now area boxed is enlarged on the Liveview area. Step 4. Resume original size with Step 1 & Step 2 Motion Detection Setup You can also use right click control to set two predefined motion detection areas,and set motion detection levels for each area. Right click on the image to display the drop down men
Summary of the content on the page No. 20
IP camera Advanced Application This chapter will cover the Advanced Application for CAM77IP, includes: * Image Setup * Capture View * Network Setup * Server Setup * Event Trigger Setup * Administration Setup * FW Update Image Setup Includes: * Resolution: Image output resolution of 3 grades: 160x120, 320x240 and 640x480. Default as 320x240. * Quality: Image Quality of 3 grades: Fine, Normal and Basic. Default as Basic. * Anti-Flicker: Anti-Flicker frequency of 3 speeds:
