Summary of the content on the page No. 1
EverFocus
Installation / Operation Instructions
EZ610
EZ610
Low Light Inline
Low Light Inline
IP66 Bullet Camera
IP66 Bullet Camera
Summary of the content on the page No. 2
EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0610001AR Operation Instruction © 2010 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. All righ
Summary of the content on the page No. 3
Precautions 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image. 2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equi
Summary of the content on the page No. 4
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu
Summary of the content on the page No. 5
Table of Contents 1 Product Overview..............................................................................................................................................7 1.1 Features ..........................................................................................................................................................7 1.2 Accessory Parts List..........................................................................................................................
Summary of the content on the page No. 6
4 RS-485 Remote Control..................................................................................................................................30 4.1 Remote control with EKB-500 keyboard........................................................................................................30 4.1.1 RS - 485 Wiring ......................................................................................................................................30 4.1.2 OSD Menu Setting by Keyboard
Summary of the content on the page No. 7
Chapter 1 1 PRODUCT OVERVIEW Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus EZ610. Get color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions. Eas
Summary of the content on the page No. 8
1.2 Accessory Parts List Please be careful when you unpack the box and the electronic device inside. Check and make sure that you have all the items listed below inside the original box: • Camera Unit x 1 • Speedy Mount Ring x 1 • Surface Wire Slot Filler x 1 • Operation Manual x 1 • Video Test Cable x 1 • Power Supply Pigtail x 1 • Mounting Kit x 1 Mounting kit includes: • Long Screws x 4 (for attaching EZ Mount Ring to mounting surface) • Short Screws x 4 (for connecting
Summary of the content on the page No. 9
1.3 Specifications EZ610 Model 1/3" SONY Super HAD II CCD Pickup Device Video Format NTSC, PAL (by model) Picture Elements 768 x 494(NTSC)/ 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 (Sens-up 256x) S/N Ratio Over 52dB (AGC off) Electronic Shutter 1/50(1/60) ~1/100,000 Video Output Main Output BNC 1.0V p-p 75 Ω, Local test output, cable provided. Gamma Correction 0.45 Lens Type DC Iris Varifocal: focal length 2.8-10mm
Summary of the content on the page No. 10
1.4 Dimensions Camera Body Camera Base Front view of EZ610 10
Summary of the content on the page No. 11
1.5 Camera Component Description Speedy-mount Ring Sunshield Use a coin or screwdriver to remove the cover Controls are inside the cover 1 2 3 4 Red: Menu mode Green: Lens mode 1) Reset: To load the factory default configuration press the button, which is inside this hole, for 3 seconds. Please gently insert a thin, non-metallic device into the hole to operate the reset button. 2) Control Key: For setting Lens & OSD menu. Press the mini-joystick and hold for 5 seco
Summary of the content on the page No. 12
Chapter 2 2 INSTALLATION This chapter will describe, in general terms, how to install the EZ610 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. 2.1 Wiring and Mounting Use the template and an appropriate tool to drill 4 holes to attach the speedy-mount ring. If no surface wire will be used, please insert the provi
Summary of the content on the page No. 13
Video & Power cables RS485 cable (optional) White: RS-485 + Black: RS-485 - Power Socket RS-485 cable Connect the power and video cables. Attach the camera to the speedy-mount ring, securing it with the 4 screws provided. Optional Power and Video connection: Note: For details of RS-485 connection please consult chapter 4, for Rs-485 setup chapter 3.2! 13
Summary of the content on the page No. 14
2.2 Adjust Camera Position Adjust the viewing angle to the desired direction. With this unique 3-axis positioning system, installers can capture images from virtually any angle, without compromising. The camera can be adjusted in 3 ways. 1st axis Use a hexagon key to loosen this screw to rotate the camera 360° 2nd axis Use a hexagon key to loosen this screw to rotate the camera 180° 14
Summary of the content on the page No. 15
3rd axis Loosen lock ring and set screw to rotate camera 360° Sunshield To remove or install the sunshield, use the hexagon wrench provided to loosen the screw at sunshield. Loosen this screw Slide rib on interior of sunshield into track on outside of camera body from front to back. Note: When properly installed, the rear of the sunshield is even with the rear of the camera body; improperly extending the sunshield to ‘shade’ the lens can co
Summary of the content on the page No. 16
Chapter 3 3 OSD MENU SETUP This chapter introduces how to change RS485 ID and Baud Rate and to configure the camera OSD menu. STEPS If you want to connect camera with keyboard or other RS-485 - controller, please refer to Section 3.2 RS485 ID & Baud Rate setting. Otherwise, please go to STEP 2. Configure the camera, as described below: 3.1 Control Key General Operation Guide Switch between Lens and Menu operation Press and hold ( ~ 5 s) the joystick button for changin
Summary of the content on the page No. 17
NOTE: For those selected items with “ ” sign in the end, there is a sub-menu for further settings. Return to Previous Page Go to “Return” by turning the mini-joystick and press the mini-joystick to return to previous page. Close the Host Menu Screen To close the menu screen, navigate to the “EXIT” item and press the mini-joystick. 3.2 RS485 ID & Baud Rate Setting Default setting for RS-485 is: Protocol: EverFocus or Pelco-D, self detecting (no setup required)
Summary of the content on the page No. 18
3.3 OSD Menu Setup 3.3.1 OSD Menu Tree Default settings are shown bold or in brackets. Lens — DC Brightness 0~100 (50) Exposure Shutter x256, x128, x64, x32, — — x16, x8, x4, x2, 1/60(NTSC) / 1/50 (PAL), FLK,1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 AGC HIGH ; MIDDLE ; — — LOW ; OFF — SENS-UP — AUTO (x8) ; OFF — BLC — OFF BLC Gain Low, Middle, High — — — Default, Left/Right, Width,
Summary of the content on the page No. 19
— Return — D-Effect — Mirror — H_MIR ; V_MIR ; OFF Gamma 0.45~1.00 — Neg_Image — ON ; OFF Return — — Motion — Off — On — Area Select — Area1-Area4 — Area Display — Off, On — Left/Right — 5~66 Width 0~93 — — — Top/Bottom — 1~60 — Height — 0~60 — Sensitivity — 0~40 — Motion View — Off, On Return — — Privacy — Off On Area Select Area1-Area4 — — —
Summary of the content on the page No. 20
3.3.2 LENS When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0 to 50. Please select RETURN and press the SETUP button if you would like to return to the previous menu. 3.3.3 EXPOSURE 3.3.3.1 SHUTTER 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “EXPOSURE” -> “SHUTTER” by usin
