Summary of the content on the page No. 1
IMAGETEAM™ 2020/4620
Area Imager Cordless System
™
System Manual
Summary of the content on the page No. 2
Disclaimer Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Hand Held Products to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Hand Held Products. Hand Held Products shall not be liable for technical or editorial errors or omissions conta
Summary of the content on the page No. 3
Statement of Agency Compliance The IT2020-5B/IT4620 system meets or exceeds the requirements of all applicable standards organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe operation is to operate them according to the agency guidelines that follow. Please read these guidelines carefully before using your IT2020-5B/IT4620 system. Regulatory and Safety Approvals for the IT2020-5B/ IT4620 Parameter Specification USA FCC Part 15, Class B Ca
Summary of the content on the page No. 4
If necessary, the user should consult the dealer or an experienced radio/ television technician for additional suggestions. The user may find the following booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Hand Held Products, Inc. is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by
Summary of the content on the page No. 5
For CE-related inquiries, please contact: Hand Held Products, Inc. Nijverheidsweg 9 5627 BT Eindhoven The Netherlands Hand Held Products shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. Regulatory Approvals for Bluetooth Radio Devices RF devices are designed to comply with the most current applicable standards on safe levels of RF energy developed by the Institut
Summary of the content on the page No. 6
Bluetooth Qualified Product Bluetooth Qualified Body approved as a Bluetooth Class II radio. UL and cUL Statement UL listed UL1950 and CSA 22.2 No.950. cUL listed UL1950 and CSA 22.2 No 950. LED Safety Statement This device has been tested in accordance with EN60825-1 LED safety, and has been certified to be under the limits of a Class 1 LED device. TÜV Statement TÜV or GS marked to EN60950 and EN60825-1. C-Tick Statement Conforms to AS/NZS 3548. C-Tick number: N10410. Mexico Certified Paten
Summary of the content on the page No. 7
Required Safety Labels IT4620 www.handheld.com B
Summary of the content on the page No. 8
' IT2020-5B ' Hand Held Products, Inc. Skaneateles Falls, NY 13153 www.handheld.com I.T.E. ACCESSORY 7D21 E153740 US and Foreign Patents Pending FCC ID: HD5MX2702B Canada IC1693BMX2702B 0682 "Made in China" B
Summary of the content on the page No. 9
Table of Contents Chapter 1 - Getting Started About This Manual............................................................... 1-1 Unpacking the System .......................................................... 1-2 IT4620 Models...................................................................... 1-2 Cordless System: Main Components.................................... 1-2 About the Battery.................................................................. 1-3 Proper Disposal of the Battery.....
Summary of the content on the page No. 10
Programming the Interface - Terminal ID Method............... 2-8 Supported Terminals............................................................. 2-9 Keyboard Country .............................................................. 2-11 Keyboard Style ................................................................... 2-13 Keyboard Modifiers............................................................ 2-14 RS-232 Baud Rate........................................................ 2-16 RS-232 Word Le
Summary of the content on the page No. 11
Single Imager Operation ....................................................... 3-5 Locked Link Mode - Single Imager ............................... 3-5 Open Link Mode - Single Imager................................... 3-6 Override Locked Imager ................................................ 3-6 Multiple Imager Operation ................................................... 3-6 Imager Name......................................................................... 3-7 Imager Report ................
Summary of the content on the page No. 12
Presentation Mode ................................................................ 4-6 Presentation LED Behavior after Decode...................... 4-7 Presentation Sensitivity.................................................. 4-7 Hands Free Time-Out ........................................................... 4-7 Reread Delay ........................................................................ 4-8 User-Specified Reread Delay ............................................... 4-8 LED Power Level
Summary of the content on the page No. 13
Data Format Editor Introduction........................................... 6-1 To Add a Data Format.................................................... 6-1 Other Programming Selections ...................................... 6-2 Data Format Editor Commands...................................... 6-2 Data Format Editor......................................................... 6-5 Data Formatter................................................................ 6-5 Alternate Data Formats ................
Summary of the content on the page No. 14
Code 11 .............................................................................. 7-16 Check Digits Required ................................................. 7-16 Code 11 Message Length............................................. 7-16 Code 128 ............................................................................ 7-17 ISBT 128 Concatenation.............................................. 7-17 Code 128 Message Length........................................... 7-18 Code 128 Code Page ..
Summary of the content on the page No. 15
EAN/JAN-8 ........................................................................ 7-27 EAN/JAN-8 Check Digit.............................................. 7-27 EAN/JAN-8 Addenda................................................... 7-28 EAN/JAN-8 Addenda Required................................... 7-28 EAN/JAN-8 Addenda Separator .................................. 7-28 MSI ....................................................................................7-29 MSI Check Character .................
Summary of the content on the page No. 16
EANUCC Emulation ........................................................ 7-40 TCIF Linked Code 39 (TLC39) ......................................... 7-40 Postal Codes ....................................................................... 7-41 Postnet.......................................................................... 7-41 Planet Code .................................................................. 7-42 British Post................................................................... 7-42
Summary of the content on the page No. 17
U.S. Currency Font .............................................................. 9-3 MICR E13 B Font ................................................................ 9-3 SEMI Font ............................................................................ 9-4 OCR Templates..................................................................... 9-4 Creating an OCR Template ............................................ 9-5 Stringing Together Multiple Formats (Creating “Or” Statements) .............
Summary of the content on the page No. 18
Quick*View........................................................................ 11-5 Installing Quick*View from the Web.......................... 11-5 Chapter 12 - Serial Programming Commands Conventions ........................................................................ 12-1 Menu Command Syntax ..................................................... 12-1 Query Commands......................................................... 12-2 Concatenation of Multiple Commands .......................
Summary of the content on the page No. 19
Maintenance........................................................................ 14-1 Cleaning the Imager’s Window.................................... 14-1 Inspecting Cords and Connectors................................. 14-1 Replacing the IT2020-5B Interface Cable: .................. 14-2 Troubleshooting Base ......................................................... 14-2 Chapter 15 - Customer Support Product Service and Repair................................................. 15-1 Technical
Summary of the content on the page No. 20
xii
