Summary of the content on the page No. 1
User Manual
• Please read this manual before operating this scanner.
� After you finish reading this manual, store it in a safe
place for future reference.
Summary of the content on the page No. 2
2. BACK-UP COPY: You may make one copy of the SOFTWARE READ CAREFULLY BEFORE OPENING THE SEALED solely for a back-up purpose or copy the SOFTWARE onto the DISK PACKAGE permanent storage device (e.g. a hard disk) of your computer and retain the original for a back-up purpose. Except as expressly CANON SOFTWARE LICENSE AGREEMENT permitted under the applicable law, any other copying of the IMPORTANT-READ THIS AGREEMENT BEFORE OPENING THE SOFTWARE is a violation of this Agreement. You must re
Summary of the content on the page No. 3
® THE ABOVE IS CANON’S ENTIRE LIABILITY AND YOUR ■ International ENERGY STAR Office Equipment EXCLUSIVE REMEDY IN CONNECTION WITH THE SOFTWARE Program ® AND ACCOMPANYING DOCUMENTATION. As an ENERGY STAR Partner, Canon Electronics Inc. has determined that this machine meets the 5. TERM: This Agreement is effective upon opening the sealed disk ® ENERGY STAR Program guidelines for energy package and remains in effect until terminated. You may terminate efficiency. this Agreement by destroyi
Summary of the content on the page No. 4
IF YOU INTEND TO DISCARD THE ORIGINALS OF SCANNED ■ Trademarks DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE • Canon and the Canon logo are registered trademarks of Canon FOR INSPECTING THE SCANNED IMAGES AND VERIFYING Inc. in the United States and may also be trademarks or THAT DATA IS INTACT. registered trademarks in other countries. THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. � Microsoft, Windows, and Windows Vista are registered UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE tradem
Summary of the content on the page No. 5
■ RADIO INTERFERENCE REGULATIONS (For 120 V Table of Contents models) This digital apparatus does not exceed the Class B limits for radio Setup Guide..........................................................................6 noise emissions from digital apparatus as set out in the Introduction........................................................................10 interference-causing equipment standard entitled “Digital Symbols Used in This Manual..........................................
Summary of the content on the page No. 6
Please read first. Setup Guide � Items included in this manual are subject to change Checking the Accessories without notice. � You must keep the machine’s packaging and packing If any of the items listed below are missing or damaged, contact your local authorized materials for storing or transporting the machine. Canon dealer or service representative. Flatbed Scanner USB Cable AC Adapter/Power Cord* User Manual Registration Card Warranty Card Setup Disc Unit 101 Type A/Type B (Connected len
Summary of the content on the page No. 7
Installing the Software Before Installation If you connect a scanner and turn it ● Do not connect the scanners to the computer before ON before you install the software, installing the software. the following wizard screen will ● Log on to Windows as an Administrator. appear. If this wizard is displayed, ● Close all other applications before installing the click the [Cancel] button to exit the software. wizard, and turn the scanner OFF. ● Make sure that the driver for the connected Canon
Summary of the content on the page No. 8
Connecting the Scanners to a Computer For scanners that use an AC adapter (DR-2010C, DR-2510C, DR-3010C) When connecting the flatbed and the Canon DR-series scanner, do not use the USB cable supplied with the DR-series scanner. Instead, use the two USB cables supplied with the flatbed. For scanners that do not use an AC adapter (DR-4010C, DR-6010C, DR-6050C, DR-7550C, DR-9050C) If you own multiple Canon DR-series scanners If you own multiple Canon DR-series scanners, with the exception of the
Summary of the content on the page No. 9
Connecting the Scanners to a Power Supply Turning the Scanners ON Turn ON the flatbed first, and then turn ON the Canon DR-series scanner. This completes the setup. 9
Summary of the content on the page No. 10
Introduction Thank you for purchasing the Canon imageFORMULA Flatbed Scanner Unit 101. Please read this manual thoroughly before using Symbols Used in This Manual the scanner to familiarize yourself with its capabilities, and to make the The following symbols are used in this manual to explain procedures, most of its many functions. After reading this manual, store it in a safe restrictions, handling precautions, and instructions that should be place for future reference. observed for safet
Summary of the content on the page No. 11
Important Safety Instructions To ensure the safe operation of this flatbed, make sure to read the ● Avoid exposing the flatbed to rapid changes in temperature. If the safety warnings and precautions described below. room in which the flatbed is installed is cold but rapidly heated, water droplets (condensation) may form inside the flatbed. This may result in a noticeable degradation in scanning quality. Installation Location ● The following conditions are recommended for optimal scanning The
Summary of the content on the page No. 12
■ Never disassemble or modify the AC adapter, as this is dangerous. Moving the Flatbed ■ When cleaning the flatbed, turn the power switch OFF and disconnect the power cord from the power supply. ● If you move the flatbed, make sure to first set the lock switch on the ■ Clean the flatbed using a slightly dampened cloth that has been well underside of the flatbed to the position to lock the scanning unit wrung out. Never use alcohol, benzene, paint thinner, or any other into place. Make sure
Summary of the content on the page No. 13
■ Connect the AC adapter only to a power outlet of the rated voltage Features and power supply frequency (120 V, 60 Hz or 220-240 V, 50/60 Hz depending on your region). The Flatbed Scanner Unit 101 is intended to be used in combination ■ When unplugging the power cord, grasp it firmly by its power plug. with the Canon DR-series document scanners. The flatbed cannot Do not pull directly on the power cord, as this may damage or operate as a stand-alone unit expose the cord’s internal wiring,
Summary of the content on the page No. 14
Names and Functions of Parts A Document Cover Close this to keep documents in place while scanning. You can fold this cover for easy document placement during continuous scanning of multiple small documents. B Scanning Glass C Power Indicator This lights when the flatbed is turned ON and flashes when scanning is in progress. D Stop Button Press this button to stop scan procedures in progress. E Start Button Press this button to start scanning the document placed on the scanning glass. F Lock
Summary of the content on the page No. 15
Documents The flatbed can scan documents ranging from 8.5" (216 mm) to 14.0" When Scanning with the Document (356 mm) in size. Cover Folded The document cover can be set to two positions when folded. Each position exposes an A5R or LTR/A4 size area, respectively, on the Placing Documents scanning glass, enabling easy document placement during Open the document cover, and place the document on the scanning continuous scanning of multiple documents. glass, as shown below, with the scanning s
Summary of the content on the page No. 16
Scanning Methods When the flatbed scanner unit is connected to a scanner and computer, you can select one of the following methods to scan Limitations documents, based on the document type and intended purpose. • To use the flatbed, you must install the software included on the provided setup disc. (See the Setup Guide page insert of this Flatbed Feeder Scanning Scanning document.) � The software that operates t he connected Canon DR-series scanner (ISIS/TWAIN driver) must also be installe
Summary of the content on the page No. 17
Support Function � Duplex scanning � Advanced Text �Folio Enhancement � Reverse side � Skip Blank Page � Staple Detection � Back-side settings � Manual Feeding � Double Feed Detection Not � Verify Count � Imprinter Supported by � Addon � Patchcode the Flatbed � Batch Separation � Speed priority � Hi-Speed Text � Auto brightness Enhancement � Custom color enhance � Drop-out color custom � Rapid recovery system � JPEG Transfer �Prescan � Margin NOTE � When using the Canon DR-series scanner to s
Summary of the content on the page No. 18
Scanning with Job Functions/CaptureOnTouch Scanning with Job Functions 3 Press the start button on the flatbed. By using Job Registration Tool or the job function in CaptureOnTouch, you can register scanning conditions as jobs. Registered jobs can be executed by pressing the start button on the flatbed. The following software supplied with Canon DR-series scanners is required to use the job function. Canon DR-Series Scanner Required Software DR-2010C, DR-2510C, CaptureOnTouch DR-3010C DR-601
Summary of the content on the page No. 19
Scanning with CapturePerfect You can use the CapturePerfect software provided with the connected CapturePerfect starts. Canon DR-series scanner to specify the scanning conditions and saving options before scanning. The following describes how to scan documents with CapturePerfect using the [Scan Batch to File] setting. When you use this scanning method, documents that are scanned one sheet at a time on the flatbed are saved to the same image file. NOTE For details on how to scan using other
Summary of the content on the page No. 20
3 Select the scanner you are using (the name of the 6 Click [Scanner Setting], and configure the scanner connected Canon DR-series scanner should be followed settings. by “w/flatbed”), and click [Settings]. The [Configure Device Settings] dialog box appears. IMPORTANT If the flatbed and the Canon DR-series scanner are connected properly, “w/flatbed” should appear after the scanner name. If only the scanner name appears, try reinstalling the software included on the setup disc provided with t
