Summary of the content on the page No. 1
Summary of the content on the page No. 2
TABLE OF CONTENTS SAFETY GUIDELINES 3 IMPORTANT SAFETY INSTRUCTIONS 3 ADDITIONAL SPECIFIC SAFETY RULES 4 BACKGROUND INFORMATION 4 OPERATION 5 MISCELLANEOUS TECHNIQUES 5 THROUGH-DOVETAILS WITH CLAMPING BOARDS 6 THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH 8 ALTERNATIVE METHOD - THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH 10 HALF-BLIND DOVETAILS WITH CLAMPING BOARDS 11 USING A ROUTER TABLE 13 ALTERNATE ROUTER BITS 14 HALF-BLIND DOVETAIL TAILBOARDS THICKER THAN 7/8" 17 MITERED THROUGH-DOVETAILS
Summary of the content on the page No. 3
SAFETY GUIDELINES - DEFINITIONS This manual contains in for ma tion that is im por tant for you to know and un der stand. This in for ma tion relates to pr o- tect ing YOUR SAFE TY and PRE VENT ING EQUIP MENT PROB LEMS. To help you rec og nize this in for ma tion, we use the symbols to the left. Please read the man u al and pay at ten tion to these sections. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardo
Summary of the content on the page No. 4
16. AVOID UNINTENTIONAL STARTING. Do not carry a plugged-in tool with finger on switch. Be sure switch is off when plugging in. Keep hands, body and clothing clear of blades, bits, cutters, etc. when plugging in the tool. 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords marked “Suitable for use with outdoor appliances – store indoors when not in use.” If an extension cord is to be used outdoors it must be marked with the suffix W-A or w following the cord
Summary of the content on the page No. 5
OPERATION MISCELLANEOUS TECHNIQUES Using these techniques can simplify your dovetailing projects. USE A DEAD-BLOW HAMMER Use a plastic dead-blow hammer to join your workpieces together to help prevent the marring of wood (Fig. 1A). CHAMFER THE TAIL EDGES Chamfering the inner tail edges can make the joints go together easier and may prevent damage to the pins (Fig. 1B). Make the chamfers with a file or a chisel. Since the chamfers are located on the inside of the joint, they will be invisible.
Summary of the content on the page No. 6
TEMPLATES MOUNTED TO CLAMPING BOARDS You can mount the jig templates to clamping boards and take the templates to the workpiece to make the joint. The benefits of this operation are: 1. You can maneuver a mounted template onto a large workpiece easier than clamping a large workpiece to the jig. This process allows you to join boards wider than 12" by routing a part of the joint, sliding the mounted template just past the original cut, and routing the remainder of the joint. Fig. 4B Fig. 4A Fi
Summary of the content on the page No. 7
Summary of the content on the page No. 8
Fig. 8A Fig. 8B Fig. 8D Fig. 8C FITTING THE JOINT Step 1 - Orient the template so that the “PINS” side is Fig. 9A facing you (Fig. 9A). Step 2 - Loosen the two #10 screws. Step 3 - If the joint is too loose, move the template toward you slightly. Step 4 - If the joint is too tight, move the template away from you slightly. Step 5- Tighten the screws loosened in STEP 2. Step 6 - Cut the pin board again and check for fit. THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH You can cut dovetails
Summary of the content on the page No. 9
CUTTING THE TAILS Step 1 - Clamp the tail board with the outside surface facing away from the clamping board (Fig. 10A). Step 2 - If the board is a width in 1" increments, (12", 13", etc.), center the edge of the board exactly between the two fingers of the template farthest to the left (Fig. 10B). Step 3 - If the board is not in 1" increments, take the fraction of an inch that is greater than 1" and divide it by two. Then move the tailboard to the left of the center of the fingers by that a
Summary of the content on the page No. 10
Step 7 - Unclamp the template, slide it down, and center the last cut between the two angled fingers and reclamp (Fig. 11D). Step 8 - Repeat STEPS 6 and 7 until the pins are cut across the entire board. Step 9 - Remove the pin board and check the fit with the tailboard. FITTING THE JOINT Fitting the joint is identical to the previous section (Fig. 12A). Fig. 11D Fig. 12A ALTERNATE METHOD THROUGH-DOVETAILS WITH UNLIMITED BOARD WIDTH This alternate method may be more accurate for correctly cut
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Fig. 15D Step 4 - Make the straight clamping block. If the workpiece is thinner than 3/4", you will need to modify the dimension (Fig. 15D). Step 5 - Make two thickness blocks the same thickness as the pin board. Drill a hole big enough for the 3/4 " (IF THE PIN BOARD IS LESS THAN 3/4" THICK, wood screw to go through (Fig. 15E). THEN REDUCE THIS DIMENSION ACCORDINGLY) Assemble the board-mounted half-blind Step 6 - template (Fig. 15F). 1-1/2 " WOOD GRAIN 1-1/2 " NOTE: You will not need to
Summary of the content on the page No. 13
Summary of the content on the page No. 14
ALTERNATE ROUTER BITS You are not limited to using the router bits supplied with your jig. Other router bits can be used to produce a different look or to work with thicker woods. Using alternate bits can help you produce more advanced joints (inlayed dovetails, etc.). Since 1/2" shank bits are stronger and are much less prone to deflection than the 1/4" shank bits, we recommend that you use the 1/2" shank bits with the 4210 and 4212 dovetail jigs, and with the 4211 and 4213 accessory kits.
Summary of the content on the page No. 15
Some items to consider when purchasing alternate bits for half-blind dovetails are: 1. A shallow angle of the bit requires a deeper cut. A steeper angle requires a shallower cut. 2. The diameter of the bit should be slightly greater than 1/2". The greater the diameter, the deeper the cut. 3. The bit should have a cutting length at least as long as the cutting depth. NOTE: When using alternate bits, ensure that the pin board (drawer front) is thicker than the depth of cut. NOTE: When using altern
Summary of the content on the page No. 16
CUTTING THE TAILS Cut the tail board (drawer side) similar to cutting the rabbeted half-blind dovetail, but remove the spacer and move the left offset guide directly against the tail board. NOTE: Support the template with a scrap workpiece thick enough to prevent the cutter from contacting the base. CUTTING THE PINS Cut the pin board (drawer front) similar to cutting the rabbeted half-blind dovetail. (If you use the alternate method of aligning the pin board with secondary board. Make sure the
Summary of the content on the page No. 17
DOVETAIL BIT TEMPLET GUIDE ROUTER SUB BASE I.D. OF TEMPLET GUIDE DOVETAIL BIT DIAMETER THERE IS A MINIMUM DEPTH OF CUT WHEN THE DIAMETER OF THE ROUTER Fig. 22A BIT IS GREATER THAN THE INSIDE DIAMETER OF THE TEMPLET GUIDE Cutting a dado with a template guide that has an OD smaller than 3/4" requires two passes. 1. Start on the left side. Keep the router toward the back edge of the dado slot, and cut to the right until you have completed the cut. 2. Start on the right side. Keep the router toward
Summary of the content on the page No. 18
MITERED THROUGH-DOVETAIL You can make a through-dovetail with a mitered edge, creating a molded edge that goes the whole way to the joint. This joint is very attractive on serving trays or decorative boxes without lids. Fig. 25A NOTE: Depending on the depth of the molded edge, you may want to make the boards slightly wider to account for the molded depth. If so, mount the tail board so that the mitered edge will end with the thicker half-pin. With the offset guide set against the tail board
Summary of the content on the page No. 19
Fig. 28A Fig. 28B Fig. 28C MITERING THE TAILS Step 1 - On the inside surface, use a square and pencil to draw a line from the base of the tails to the edge where the miter will be cut (Fig. 29A). Step 2 - Set the table saw blade so that the height of cut of the saw blade is the same as the thickness of the mitered half-pin. Step 3 - Use a table saw with the miter gauge set to 45° to miter the tails. You will need to make several passes to cut out the material (Fig. 29B). NOTE: A dado head
Summary of the content on the page No. 20
CUTTING THE PINS Step 1 - Hold the pin board against the tail board and mark the edges of the tails on the end of the pin board (Fig. 32A). Shade in the areas on the end of the pin board where the tails will be (Fig. 32B). Step 3 - Cut all the pins (Fig. 32C). Step 4 - Slide the pin board to the right 1/4" (Fig. 32D). Step 5 - Cut in between the fingers of the template to cut only in the shaded area (A) Fig. 32D. Step 6 - Repeat STEPS 4 and 5 until all of the material between the pins has b
