Summary of the content on the page No. 1
COMPACT VHS CAMCORDER
VIDEOCAMARA VHS COMPACTO
CÂMERA VHS COMPACT
GR-AX827/GR-AX727
GR-AX627/GR-AX527
Compact VHS
(The camcorder illustrations appearing in
these instructions are of the GR-AX827.)
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRUÇÕES
YU30052-532-1
PORTUGUÊS ESPAÑOL ENGLISH
Summary of the content on the page No. 2
2 Dear Customer, Warning on lithium battery Thank you for purchasing the JVC Compact VHS The battery used in this device may present a camcorder. Before use, please read the safety fire or chemical burn hazard if mistreated. Do information and precautions contained in the not recharge, disassemble, heat above 100°C or following pages to ensure safe use of your new incinerate. camcorder. Replace battery with Panasonic (Matsushita Electric), Sanyo or Maxell CR2025; use of another battery may prese
Summary of the content on the page No. 3
3 IMPORTANT PRODUCT ANTENNA INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS 1. Outdoor Antenna Grounding Electrical energy can perform many useful functions. But If an outside antenna or cable system is connected improper use can result in potential electrical shock or fire to the product, be sure the antenna or cable system hazards. This product has been engineered and is grounded so as to provide some protection manufactured to assure your personal safety. In order not to against voltage surges
Summary of the content on the page No. 4
4 USE SERVICING 1. Accessories 1. Servicing To avoid personal injury: If your product is not operating correctly or exhibits a • Do not place this product on an unstable cart, stand, marked change in performance and you are unable to tripod, bracket or table. It may fall, causing serious injury restore normal operation by following the detailed to a child or adult, and serious damage to the product. procedure in its operating instructions, do not attempt to • Use only with a cart, stand, tripod,
Summary of the content on the page No. 5
QUICK OPERATION GUIDE 5 SUPPLY POWER INSERTING A VIDEO CASSETTE Hook on. 1 EJECT 1 Push in. 2 3 PUSH 2 Insert. BATT. RELEASE Using the battery pack 1 Hook-on the battery pack’s top end to the 1 Slide EJECT. camcorder. (Charging procedure, Z pg. 8) 2 Insert a video cassette. 2 Push in the battery pack until it locks into 3 Press PUSH. place. (For more details, Z pg. 11) To remove the battery pack Slide BATT. RELEASE and pull out the battery pack. PLAYBACK SHOOTING PLAY/PAUSE 3 REW 2 1 LENS COV
Summary of the content on the page No. 6
MAJOR FEATURES 6 REMEMBER Intelligent Function Control (Z P. 18 – 25) The Logical Choice F1 SEL F2 The only compact video Variable-Speed Hyper Zoom cassettes that can be used with your VHS VCR* Z P. 15) ( *with VHS Playpak Zoom-in T T T T Program AE with Special W W W W Z P. 16) Effects ( Zoom-out n Auto Mode Lock n Auto Mode Release n Electronic Fog Filter n ND Effect n Sepia n Twilight n Sports Random Assemble Editing n High Speed (1/2000 sec.) Shutter n 15 sec. Self Timer (Z P. 32 – 35) 2
Summary of the content on the page No. 7
CONTENTS 7 GETTING STARTED 8 Power .......................................................................................... 8 Clock (Lithium) Battery Removal/Insertion............................................. 10 Date/Time Settings ........................................................................ 10 Viewfinder Adjustment .................................................................... 11 Tape Length/Recording Mode Setting ................................................... 11 Loa
Summary of the content on the page No. 8
GETTING STARTED 8 Power This camcorder’s 3-way power supply system lets you choose the most appropriate source of power. NOTES: c No function is available without power supply. c Use only specified power supply. c Do not use provided power supply units with other equipment. CHARGING THE BATTERY PACK CHG. (charge) indicator SUPPLY POWER Marks Connect the charger’s AC power cord to a wall POWER 1 outlet. The power indicator lights. To AC outlet indicator ATTACH BATTERY PACK Align the marks and sli
Summary of the content on the page No. 9
9 **CHARGE MARKER A charge marker is provided on the battery pack to Charge marker help you remember whether it has been charged or not. Two colors are provided (red and black)—you choose which one means charged and which means discharged. NOTES: c The recording time per charge is affected by such factors as the time spent in Record/Standby mode and the frequency of zooming. It is safer to have spare battery packs. c Charging times noted on page 8 are for fully discharged battey pack, and discha
Summary of the content on the page No. 10
GETTING STARTED (cont.) 10 Clock (Lithium) Battery Removal/Insertion A This battery is necessary for clock operation and to perform date/time settings. SWITCH OFF POWER Switch off the unit’s power and remove the power 1 supply unit. OPEN COVER Open the clock battery compartment cover while 2 pressing the release tab. REMOVE BATTERY (when replacing) Insert a pointed, non-metallic object between the 3 battery and the compartment ( A ) and pull the battery out. INSERT BATTERY Ensuring the plus (+)
Summary of the content on the page No. 11
11 Viewfinder Adjustment SP-EP recording mode and T20•30•40 tape length select button POSITION VIEWFINDER Adjust the viewfinder manually for best viewability 1 (see illustration at left). SELECT MODE Set the power switch to CAMERA. 2 ADJUST DIOPTER Turn the diopter adjustment control until the 3 indications in the viewfinder are clearly focused. Tape Length/Recording Mode Setting SET TAPE LENGTH Set the tape length button according to the length of 1 the tape used. T20 = 20 minutes of recording
Summary of the content on the page No. 12
GETTING STARTED (cont.) 12 Grip Adjustment EXPAND LOOP Separate the Velcro strip. 1 INSERT HAND Pass your right hand through the loop and grasp the 2 grip. ADJUST STRAP LENGTH Adjust so your thumb and fingers can easily operate 3 the Recording Start/Stop button and Power Zoom Recording Start/Stop button switch. Refasten the Velcro strip. Shoulder Strap Attachment ATTACH STRAP Following the illustration at left, thread the strap 1 through the top of the eyelet (1), then fold it back 1 and thread
Summary of the content on the page No. 13
30° 30° 13 Remote Control Unit The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (PLAY, STOP, PAUSE, FF, and REW) of your Infrared beam VCR. This remote control unit makes additional effective area recording functions possible. 10° Before use, refer to the instruction booklet. PULL OUT BATTERY HOLDER Infrared beam sensor window Pull out the battery holder by inserting a pointed 10° 1 A instrument into slot . The transmitted beam may
Summary of the content on the page No. 14
RECORDING Basic Recording 14 NOTE: LENS COVER You should already have performed the procedures listed SWITCH below. If not, do so before continuing. c Power (Z pg. 8) c Tape Length/Recording Mode Setting (Z pg. 11) c Grip Adjustment (Z pg. 12) LOAD A CASSETTE Slide EJECT to open the cassette holder, then insert 1 the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked. ENTER RECORD–STANDBY MODE POWER Slide the LENS COVER open/close switch to open 2 the lens
Summary of the content on the page No. 15
RECORDING Basic Features 15 FEATURE: Zooming Zoom indicator PURPOSE: Varies the focal length of the lens and Zoom-in produces the zoom in/out effect. Zoom In OPERATION: T T T T 1) Pull the power zoom switch down toward “T”. W W W W Zoom Out 2) Push the switch up toward “W”. Zoom-out NOTES: c The further the power zoom switch is pushed, the faster the zoom speed becomes. c Focusing may become unstable during zooming. In this case, set the zoom while in Record–Standby, set manual focus or RETAKE
Summary of the content on the page No. 16
RECORDING Advanced Features 16 Program AE With Special Effects All you have to do to access any of the variety of shooting effects is to turn the PROGRAM AE select dial until the desired indication appears in the viewfinder. The mode is activated about 1 second PROGRAM AE later. select dial DIAL VIEWFINDER Tally lamp MODE SYMBOL INDICATION LOCK AUTO LOCK Auto Mode Lock A DIAL VIEWFINDER Auto Mode Lock MODE SYMBOL INDICATION Locks the camcorder in Full Auto mode, preventing incorrect operation
Summary of the content on the page No. 17
17 White Balance Adjustment White balance mode indicator This camcorder’s Automatic Color Temperature system senses the color temperature of the ambient lighting for No indication
automatic white balance adjustment. However, precise (Auto) color adjustment is not possible under the following conditions: •When an object is in various shades of the same color. MWB •When a predominantly red or brown object is being shot outdoors. In these cases, use the camcorder’s built-in preset filters for whi
Summary of the content on the page No. 18
RECORDING Advanced Features 18 Video Light (GR-AX827/AX627 only) When natural lighting is too dim, you can brighten the scene by using the built-in video light. SET VIDEO LIGHT Set the LIGHT ON/AUTO/OFF as required. 1 ON : Always keeps the light on as long as the camcorder is turned on. AUTO : Automatically turns on the light when the camcorder senses insufficient lighting on the subject. LIGHT ON/AUTO/OFF OFF : Turns off the light. DANGER: •The video light can be used with the camcorder’s n T
Summary of the content on the page No. 19
19 Fader F1 button F2 button This feature allows smooth fade-in and fade-out to black blank screen. Fade-in works at recording start, and fade-out works at recording end or when you enter F1 Record–Standby mode. SEL F2 SELECT MODE Press Function SEL. repeatedly until “FADER” Function SEL. button 1 appears to the right of F1. PROGRAM AE select dial ENGAGE FADE–STANDBY MODE Press F1 to engage the Fade–Standby mode. 2 “FADER”appears in the viewfinder. START RECORDING Press Recording Start/Stop to s
Summary of the content on the page No. 20
RECORDING Advanced Features 20 Focusing Auto Focus Focus The camcorder’s Full Range AF system offers continuous detection zone shooting ability from close-up to infinity. However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): •When two subjects overlap in the same scene. •When illumination is low.* •When the subject has no contrast (difference in F1 F2 brightness and darkness), such as a flat, one-color wall, or a clear, blue sky.* •Wh
