Summary of the content on the page No. 1
Table of Contents
Rear Blade
RB4596, RB45108 & RB5596
10347
Model RB55 10351
Model RB45
301-133M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
!
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2007 Printed 5/21/07
Cover photo may show optional equipment
not supplied with standard unit.
Summary of the content on the page No. 2
Land Pride Table of Contents Table of Contents Important Safety Information . . . . . . . . . . .1 Section 3: Operating Procedures . . . . . .11 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Check List . . . . . . . . . . . . . . . . . . . . . .11 Look For The Safety Alert Symbol . . . . . . . . . . . . . 1 Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Basic Op
Summary of the content on the page No. 3
REMOVE Land Pride Table of Contents Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look For The Safety Alert Symbol Thoroughly read and understand The SAFETY ALERT SYMBOL indicates there is a the instructions given in this potential hazard to personal safety involved and extra manual before operation. Refer to safety precaution must be taken. When you see this t
Summary of the content on the page No. 4
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Use the following maximum Use Safety Transport speed - tow load weight ratios as Lights and Devices Machinery Safely a guideline: Slow moving tractors, self- Comply with state and local laws. 20 mph when weight is less than or equal to the weight of propelled equipment, and towed Maximum transport speed for implements can create
Summary of the content on the page No. 5
Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Avoid High Wear Prepare for Emergencies Pressure Fluids Hazard Protective Equipment Be prepared if a fire starts. Escaping fluid under pressure can Protective clothing and equipment Keep a first aid kit and fire penetrate the skin causing serious should be worn. extinguisher handy. injury. Wear clothing and equipment Keep emergen
Summary of the content on the page No. 6
Land Pride Table of Contents Important Safety Information specified by Land Pride. When ordering new components Safety Labels make sure the correct safety labels are included in the Your Rear Blade comes equipped with all safety labels in place. request. They were designed to help you safely operate your implement. 4. Refer to this section for proper label placement. Read and follow their directions. To install new labels: a. Clean the area the label is to be placed. 1. Keep all safety labels cl
Summary of the content on the page No. 7
Land Pride Table of Contents Introduction Introduction Land Pride dealer. A dealer has trained personnel, repair Land Pride welcomes you to the growing family of new parts and equipment needed to service the Rear Blade. product owners. The parts on your Rear Blade have been specially This implement has been designed with care and built by designed and should only be replaced with genuine Land skilled workers using quality materials. Proper assembly, Pride parts. Therefore, should your Rear Blade
Summary of the content on the page No. 8
Land Pride Table of Contents Section 1: Assembly and Setup Section 1: Assembly and Setup 11. Remove rotation lock pin (#3). Rotate blade panel RB45 & RB55 Rear Blade (#2). If panel rotates too hard or is too loose, remove Refer to Figure 1-1: cotter pin (#13). Tighten or loosen castle nut (#11) to 1. Uncrate blade Assembly from shipping crate. adjust pivoting movement to desired tension. Reinstall cotter pin (#13) bending both legs around 2. Remove front hitch assembly (#1) from blade castle nut
Summary of the content on the page No. 9
Land Pride Table of Contents Section 1: Assembly and Setup Tractor Hook-Up RB55 3-Point Hitch Settings Refer to Figures 1-2, 1-3, 1-4 & 1-5: Category ll Standard Hitch: Refer to Figure 1-3: Hitch pins (#2) are inserted from the outer lug. Place ! DANGER spacer adapter (#1) on hitch pin (#2) outside of the inner Tractor hook-up to equipment is dangerous and can result in most lug and secured with lock pin (#3). serious injury or death. Do not allow anyone to stand between the blade and tractor du
Summary of the content on the page No. 10
Land Pride Table of Contents Section 1: Assembly and Setup Blade Offset Cylinder Blade Tilting Cylinder Refer to Figure 1-6: Refer to Figure 1-6: IMPORTANT: Attach cylinder base to the front hitch IMPORTANT: Attach cylinder base to the upper lug. The cylinder base will interfere with the main mounting lug. frame if attached to the rear lug. Assemble hydraulic hoses to the hydraulic cylinder Assemble hydraulic hoses to the hydraulic cylinder before placing cylinder on the blade. before placing cy
Summary of the content on the page No. 11
Land Pride Table of Contents Section 1: Assembly and Setup 2. Insert skid shoe (#2) into skid shoe bracket (#1). Manual Blade Offset Secure with clevis pin (#3) and hair pin cotter (#4). Refer to Figure 1-7: 3. Repeat steps 1 and 2 for the other side. 1. Attach blade offset links to the left or right side of the blade as shown with two clevis pins and secure with hair pin cotters. 2. Adjust offset angle by removing the hitch pin and moving outer link to a different hole. Replace hitch pin and se
Summary of the content on the page No. 12
Land Pride Table of Contents Section 2: Adjustments Section 2: Adjustments Blade Pitch RB45 Blade Offset Blade pitch can be adjusted by lengthening or shortening the tractor’s top center 3-point link. ! CAUTION The blade may come in contact with the tractor rear tire when Blade Angling and Reversing offsetting blade to maximum position and angling blade in the Refer to Figure 1-7 on page 9: same direction to most severe angle. Manual Blade Offset ! CAUTION The blade will offset to the right if t
Summary of the content on the page No. 13
Land Pride Table of Contents Section 3: Operating Procedures Section 3: Operating Procedures 1. When traveling on roadways, transport in such a way Operating Check List that faster moving vehicles may pass you safely. Hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper 2. Leave enough clearance on both sides of the blade training involved in the operation, transport, when traveling straight or making turns to keep the maintenance and storage of t
Summary of the content on the page No. 14
Land Pride Table of Contents Section 3: Operating Procedures easily performed by reversing the blade and operating General Operating Instructions the tractor in reverse or commonly called the push mode. Once you have familiarized yourself with the Operator’s Manual, completed the operations checklist, and If you are performing the construction of soil contours or properly attached your Land Pride blade to your tractor, waterways you will probably need to set a tilt angle on the you are now almos
Summary of the content on the page No. 15
Land Pride Table of Contents Section 4: Options Section 4: Options Skid Shoes The skid shoes are attached to both ends of the blade to help prevent damage to the surface of the ground by the blade. Refer to the skid shoe manual for assembly instructions and operations. Kit Bundle 301-110A SKID SHOE ASSEMBLY 15002 5/21/07 RB4596, RB45108 & RB5596 Rear Blade 301-133M 13
Summary of the content on the page No. 16
Land Pride Table of Contents Section 5: Maintenance and Lubrication Section 5: Maintenance and Lubrication Maintenance Proper servicing and adjustment is the key to the long life ! WARNING of any implement. With careful and systematic Do not alter the Rear Blade. Altering the blade can adversely inspection, you can avoid costly maintenance, time and affect its performance and reliability causing damage to the repair. blade, tractor and/or bodily injury. Always replace damaged parts with original
Summary of the content on the page No. 17
Land Pride Table of Contents Section 6: Specifications & Capacities Section 6: Specifications & Capacities RB45 & RB55 Series Rear Blades Model/Series RB4596 RB45108 RB5596 Blade Width 96” 108” 96” Approximate Weight (lbs.) 890 * 940 * 1330 * Max. Gross Vehicle Weight (G.V.W.) 9,500 lbs. 9,500 lbs. 15,000 lbs. Horsepower Rating 90 180 Hitch Type Cat. 2 Cat. 2 & 3 Fits Land Pride Quick Hitch Blade Thickness 1/4” reinforced 5/16” reinforced Blade Height 19” Angle/Position 6 Forward up to 45 degrees
Summary of the content on the page No. 18
Land Pride Table of Contents Section 7: Features and Benefits Section 7: Features and Benefits RB45 Series Rear Blade Features Benefits Working widths 96”, 108” HP Range 70 - 110 HP 7 Forward and 7 reverse Various positions to work in various conditions to get desired results. positions Tilt left or right Tilt moldboard left or right for ditching. Offset left or right Position the moldboard beyond tractor tire and enable to work closer to obstructions. Rolled moldboards Material ‘rolls’ which cau
Summary of the content on the page No. 19
Land Pride Table of Contents Section 7: Features and Benefits RB55 Series Rear Blades Features Benefits Working widths 108”, 120” Tractor HP Range 90-180 HP Cat. 2 and 3 Bushing provided to go from Cat. 2 to Cat. 3 enables a wider variety of tractors to be used. 7 Forward and 7 reverse Various positions to work in various conditions to get desired results. positions Tilt left or right Tilt moldboard left or right for ditching. Offset left or right Position the moldboard beyond the tractor tire an
Summary of the content on the page No. 20
Land Pride Table of Contents Section 8: Appendix Section 8: Appendix Torque Values Chart Bolt Head Identification Bolt Head Identification 8.8 10.9 5.8 Bolt Size Bolt Size (Inches) (Metric) Class 5.8 Class 8.8 Class 10.9 Grade 2 Grade 5 Grade 8 1 3 in-tpi N·m ft-lb N · m ft-lb N · m ft-lb mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb 1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 436597 1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11 5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27 5/16" -
