Summary of the content on the page No. 1
MODEL G0536
16" SCROLL SAW
INSTRUCTION MANUAL
COPYRIGHT © OCTOBER 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#5763 PRINTED IN CHINA
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE
CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF T
Summary of the content on the page No. 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of
Summary of the content on the page No. 3
Table Of Contents SECTION 1: SAFETY ................................................................................................................................2 Safety Instructions For Power Tools....................................................................................................2 Additional Safety Instructions For Scroll Saws ....................................................................................4 SECTION 2: INTRODUCTION.........................................
Summary of the content on the page No. 4
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substi- tute for proper accident prevention measures.
Summary of the content on the page No. 5
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD. Make 15. USE RECOMMENDED ACCESSORIES. sure your extension cord is in good condi- Consult the owner’s manual for recommend- tion. Conductor size should be in accor- ed accessories. The use of improper acces- dance with the chart below. The amperage sories may cause risk of injury. rating should be listed on the motor or tool nameplate. An undersized cord will cause 16. REDUCE THE RISK OF UNINTENTIONAL a drop in line voltage resulti
Summary of the content on the page No. 6
Additional Safety Instructions For Scroll Saws 1. SCROLL SAW SAFETY BEGINS with 7. USE BLADES APPROPRIATE FOR your lumber. Inspect your stock carefully YOUR MACHINE, material being cut, and before you begin a cut. If you have any the type of cut that you are performing. doubts about the stability or structural integrity of your stock, DO NOT CUT! 8. DO NOT START THE SAW WITH THE BLADE IN CONTACT WITH THE WORK- 2. KEEP HANDS AWAY FROM BLADE. DO PIECE. NOT hold pieces so small that your fingers go
Summary of the content on the page No. 7
SECTION 2: INTRODUCTION Most importantly, we stand behind our machines. Commentary If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Lack of familiarity with Muncy, PA 17756 this manual could Phone: (570) 546-9663 cause serious person- Fax: (800) 438-5901 al injury. Become E-Mail: techsupport@grizzly.com familiar with the con- Web Site: http://www.grizzly.com tents of this manual, includi
Summary of the content on the page No. 8
SECTION 3: CIRCUIT REQUIREMENTS Circuit Breaker Requirements 110 Volt Use the following guidelines when choosing a cir- cuit breaker for your machine: Amperage Draw Recommended Circuit Breaker ..............5 Amp The Model G0536 motor is wired to operate at 110V and draw the following load: Your Circuit Capacity Always check to see if the wires in your circuit are Motor Load ..........................................1.4 Amps capable of handling the amperage load from your machine. If you are uns
Summary of the content on the page No. 9
Grounding Extension Cords In the event of an electrical short, grounding Operation If you find it necessary to use an extension cord: reduces the risk of electric shock by providing a path of least resistance to disperse electric cur- • Make sure the cord is rated Standard Service rent. This tool is equipped with a power cord that (grade S) or better. has an equipment-grounding prong. The outlet must be properly installed and grounded in accor- • The extension cord must also contain a dance wit
Summary of the content on the page No. 10
SECTION 4: MACHINE FEATURES Blade Guard Upper Arm Table Throat Plate Blade Tension Adjustment Knob -8- G0536 Scroll Saw
Summary of the content on the page No. 11
Blade Guard Angle Scale Table Tilt Knob ON/OFF Switch Variable Speed Knob Motor Upper Blade Holder Blade Dust Blower Lower Blade Holder Figure 2. Machine features. G0536 Scroll Saw -9-
Summary of the content on the page No. 12
SECTION 5: SET UP Unpacking G0536 Inventory The machine was carefully packed when it left the A. Blade Guard ..............................................1 B. Blade ..........................................................1 Grizzly warehouse. If you discover the machine is C. Dust Blower and Mounting Plate................1 damaged after you have signed for delivery, and D. Hex Bolt and Knurled Nut ..........................1 the truck and driver are gone, you will need to file a freight claim
Summary of the content on the page No. 13
Site Considerations Clean Up Weight Load The unpainted surfaces are coated with a waxy The Model G0536 Scroll Saw is a small weight oil to protect them from corrosion during ship- load with a small footprint. Most workbenches ment. Remove this protective coating with a sol- should be sufficient to carry the weight of the vent cleaner or citrus-based degreaser such as machine. Reinforce the workbench if you ques- Grizzly’s G7895 Degreaser. To clean thoroughly, tion its ability to support the weig
Summary of the content on the page No. 14
Beginning Assembly Attach Blade Guard This section covers the basic assembly and adjust- To attach the blade guard: ment instructions needed to begin operation. Complete the assembly in the order provided in this 1. Set the blade guard on the scroll saw table manual and then read the remaining portion of the and position it around the upper arm. manual before attempting any type of operation. 2. Thread the bolt through the blade guard Your safety is important! Please follow the components as sho
Summary of the content on the page No. 15
Installing Blades Test Run To install the blade: Once the assembly is complete, the machine needs to be tested. The purpose of the test run is 1. Disconnect the machine from the power to ensure that there are no problems. source. To test run the scroll saw: 2. Feed the blade through the table and hook into the lower blade holder as shown in 1. Remove all tools from the scroll saw. Figure 6. The blade teeth should face for- ward and down. 2. Turn the variable speed setting down to 550 SPM. 3. Plu
Summary of the content on the page No. 16
SECTION 6: OPERATIONS General Blade Speed This section will cover basic scroll sawing opera- It is important to adjust the blade speed for the tions. Please read the remaining portion of the type of material being cut. Generally harder mate- manual before attempting any type of operation. rials require a slower blade speed. Your safety is important! Please follow the To adjust the blade speed: warnings below during this entire section: Rotate the knob, shown in Figure 7, clockwise to increase t
Summary of the content on the page No. 17
5. Feed the blade through the table and hook it Changing Blades into the lower blade holder as shown in Figure 10. The teeth should face forward and down. 1 A typical scroll saw blade will wear out in ⁄2 to 2 hours, depending on the material cut. Blades become dull quicker when cutting thick material, plywood, laminates, hardwoods and metal. To change the blade: 1. Disconnect the machine from the power source 2. Remove the throat plate and the lower arm guard shown in Figure 8. Throat Plate Figu
Summary of the content on the page No. 18
Straight Cuts Curved Cuts Miter gauges and fences are not effective on When cutting curves, preplan your cut and leave scroll saws because most scroll saw blades are tight inside curves for a second pass to minimiz- narrow and tend to follow the grain of the wood. ing backing out. Cut sharp outside curves by cut- Freehand cutting allows the operator to compen- ting past the curve and looping around to cut from sate for blade drift. a different angle. To make a straight cut: To make a curved cut:
Summary of the content on the page No. 19
Inside Cuts Bevel Cuts Inside cuts such as circles or the insides of closed Bevel cuts can be used for miters, cope joints, letters can be easily cut with your scroll saw by and making relief or recessed projects. threading the blade through a hole drilled in the workpiece. To make a bevel cut: To make an inside cut: 1. Draw your pattern as described in the previ- ous sections. 1. Disconnect the machine from the power source. 2. Adjust the table to the desired angle. 2. Remove blade and throat p
Summary of the content on the page No. 20
SECTION 7: MAINTENANCE Maintenance Safety General Your safety is important! Please follow the Regular periodic maintenance on the Model warnings below during this entire section: G0536 will ensure optimum performance. Make a habit of inspecting the machine each time you use it. Before each use, look for the following condi- Always disconnect tions: ! power to the machine before performing main- 1. Loose bolts. tenance. Failure to do this may result in serious 2. Damaged blades. personal injury.
