Summary of the content on the page No. 1
MODEL G1023RL SERIES
10" LEFT-TILT TABLE SAW
WITH RIVING KNIFE
OWNER'S MANUAL
G1023RLX
G1023RL G1023RLW/RLWX
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: SHOP MADE SAFETY ACCESSORIES .............................................. 45 SECTION 1: SAFETY ....................................... 5 SECTION 2: POWER SUPPLY ...................... 10 SECTION 6: AFTERMARKET ACCESSORIES FROM GRIZZLY ............................................. 53 SECTION 3: SETUP ........
Summary of the content on the page No. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Summary of the content on the page No. 5
Identification G1023RL For Your Own Safety Read Instruction Manual Before Operating Saw a) Wear eye protection. G1023RLX b) Use saw-blade guard and spreader for every operation for which it can be used, including all through sawing. c) Keep hands out of the line of saw blade. d) Use a push-stick when required. e) Pay particular attention to instructions on reducing risk of kickback. f) Do not perform any operation freehand. g) Never re
Summary of the content on the page No. 6
Machine Data Sheet MODEL G1023RL Series 10" LEFT-TILTING TABLE SAWS G1023RL G1023RLX G1023RLW G1023RLWX Model Number Motor Required Power Supply Circuit Speed Power Requirement Full Load Current Rating Power Connection Device Table Size (full assembly) Table Height Above Floor Overall Machine Size Footprint Size Weight Fence Type Router Ta
Summary of the content on the page No. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Summary of the content on the page No. 8
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Summary of the content on the page No. 9
Additional Safety for Table Saws HAND POSITIONING. FENCE. PUSH STICKS/BLOCKS. BLADE GUARD. CUT-OFF PIECES. OFF BLADE ADJUSTMENTS. RIVING KNIFE. OFF CHANGING BLADES. DAMAGED SA
Summary of the content on the page No. 10
Preventing Kickback Take the precautions below to avoid the most common causes of kickback: Statistics show that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck
Summary of the content on the page No. 11
Glossary of Terms VERY Arbor: Parallel: Bevel Edge Cut: Perpendicular: Page 37 Blade Guard Assembly: Push Stick: Page 31 Page 49 Rabbet: Crosscut: Page 40 Page 36 Rip Cut: Dado Blade: Page 35 Riving Knife: Dado Cut: Page 37 Page 34 Featherboard: Spreader: Page 45 Kerf: Straightedge: Kickback:
Summary of the content on the page No. 12
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult a qualified electrician if you are unsure about wiring practices or Electrocution, fire, or electrical codes in your area. equipment damage may occur if machine is not correctly grounded and Note: The circuit requirements listed in this man- connected to the power ual apply to a dedicated circuit—where only
Summary of the content on the page No. 13
Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual. G1023RL/RLW/RLX Connection Type & Grounding Min. Gauge (G1023RL/RL/RLW) .........14 AWG Maximum Length (Shorter is Better).......50 ft. GROUNDE
Summary of the content on the page No. 14
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the Page 17 machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment
Summary of the content on the page No. 15
Hardware Recognition Chart
Summary of the content on the page No. 16
Inventory NOTICE Figure 3. If you cannot find an item on this list, check the mounting location on the machine or the packaging materials. Sometimes parts are pre-installed for shipping, or they become hidden by packaging materials. Table Saw Unit Box Contents: (Figures 3–5) Qty A. B. C. D. E. F. G. Figure 4. H. I. J. K. L. M. N. O. P. Q. Hardware
Summary of the content on the page No. 17
Fence & Rail Inventory Router Table & Guard Inventory G1023RL, G1023RLW, G1023RLWX G1023RLW, G1023RLWX Box Contents (Figures 7 –8) Qty A. B. C. Figure 6 D. E. F. G. Box Contents (Figure 6): Qty H. A. I. B. C. D. E. Figure 7. Figure 6. Hardware and Tools (Not Shown):
Summary of the content on the page No. 18
Hardware and Tools (Not Shown): Fence & Rail Inventory G1023RLX Router Table Figure 9 Box Contents (Figure 9) Qty A. B. Guard C. D. E. F. G. H. I.
Summary of the content on the page No. 19
Cleanup Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. NOTICE Avoid chlorine-based s
Summary of the content on the page No. 20
Site Considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted lo
