Grizzly G0504 user manual

User manual for the device Grizzly G0504

Device: Grizzly G0504
Category: Saw
Manufacturer: Grizzly
Size: 9.54 MB
Added : 9/3/2013
Number of pages: 76
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Grizzly G0504. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Grizzly G0504.

For your convenience

If looking through the Grizzly G0504 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Grizzly G0504 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Grizzly G0504 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Grizzly G0504 User manual - Online PDF
Advertisement
« Page 1 of 76 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Grizzly G0504 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Grizzly G0504. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

MODEL G0504
16" HORIZONTAL
RESAW BANDSAW
Owner's Manual
COPYRIGHT © MAY, 2003 BY GRIZZLY INDUSTRIAL, INC. REVISED MARCH, 2007.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR5063 PRINTED IN TAIWAN

Summary of the content on the page No. 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Summary of the content on the page No. 3

Table of Contents SECTION 1: GENERAL INFORMATION ......................................................................................... 3 Commentary ............................................................................................................................... 3 Machine Data Sheet ................................................................................................................. 4 SECTION 2: SAFETY ................................................................

Summary of the content on the page No. 4

SECTION 8: SERVICE ADJUSTMENTS ....................................................................................... 35 About Service ........................................................................................................................... 35 Adjusting Lower Blade Guides ................................................................................................. 35 Adjusting V-Belt Tension ..................................................................................

Summary of the content on the page No. 5

SECTION 1: GENERAL INFORMATION If you have any comments or criticisms that you feel we should address in our next printing, please contact us at: Read this entire manu- al before operating the Grizzly Industrial, Inc. machine, or you will C ⁄O Technical Documentation greatly increase your P.O. Box 2069 chances of serious per- Bellingham, WA 98227 sonal injury! Email: manuals@grizzly.com Most important, we stand behind our machines. Commentary We have excellent regional service departments

Summary of the content on the page No. 6

Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MODEL G0504 16" HORIZONTAL RESAW BANDSAW Overall Dimensions: Conveyor Table .................................................................................... 16" W x 102" D Height From Floor To Table .....................................................................................40" Height From Floor To Return Table ........................................

Summary of the content on the page No. 7

safety SECTION 2: SAFETY � � � �� � �� � �� � � � �� � � � �� � � � �� � � �� � � � � � � �� � � � �� � � � � � � �� � � �� � � � � � �� � � � � ��� � � � � � � � � �� � � � �� � � � � � � � � � �� � � � � � � �� � �� � � � � � �� � � � � � � �� � �� � �� � � � � � � �� � �� �� � � � � � � � � �� � �� � � � � � � � �� � � � � � � ���� � � � � �� � � � � �� � � � �� � � � � � �� �� � �� �� � � � � � �� � �� � � � � � � �� � � �� � � � � � �� � � � � �� � � � � � � � �� � �� � � � � � �� � � �� �

Summary of the content on the page No. 8

� � � � � �� � � � � � � �� � � � �� � � �� � � � � � � � � � ��� ����� ������ �������� ���� ���� � ���� � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� ���������� ����� �� ������ ��� ��������� ���� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � ����� ���� ���������� ��������� ������� ���� � ���������� ������������� ���� ����� ���� �������� ���� ���������� �� � ����������� ���� � � � � � � � � � � � � � � � � � � � � � � �

Summary of the content on the page No. 9

Additional Safety Instructions for Bandsaws 1. DO NOT OPERATE WITH DULL OR 9. THIS MACHINE IS NOT DESIGNED TO BADLY WORN BLADES. Dull blades CUT METAL or other material except require more demand on the motor and are wood. less likely to cut precisely. Inspect blades before each use. 10. DO NOT MANUALLY STOP OR SLOW BLADE after turning the saw off. Allow 2. NEVER POSITION FINGERS OR THUMBS it to come to a complete stop before you IN LINE WITH THE CUT. Serious personal leave it unattended.

Summary of the content on the page No. 10

Additional Safety Instructions for Hydraulics 1. BE FAMILIAR WITH THE HAZARDS OF 4. STOP THE MACHINE IF YOU NOTICE HYDRAULIC INJECTION INJURIES. A HYDRAULIC LEAK. Allowing the machine to continue running with a leak — Leaking hydraulic fluid may have may increase the hazard of the situation. enough pressure to penetrate skin. 5. DEPRESSURIZE THE HYDRAULIC Never use your hands to check for SYSTEM BEFORE ATTEMPTING TO suspected hydraulic leaks. ADJUST ANY HYDRAULIC LINES OR FITTINGS. Stop

Summary of the content on the page No. 11

SECTION 3: CIRCUIT REQUIREMENTS Connection Type 3-Phase Power This machine is intended to be installed in a semi-permanent location and hardwired to the power source by a qualified electrician, using a supply circuit disconnect device with the capa- bility of being locked in the OFF (open) position Serious personal injury could occur if you (see Figure 1). allow power to the machine before complet- ing the setup process. DO NOT allow power to the machine until instructed to do so. Amperag

Summary of the content on the page No. 12

Grounding Converting to 440V Converting the Model G0504 to 440V operation consists of 1) wiring the voltage transformer, 2) replacing the overload relays with those provided Electrocution or fire could in the G0504 440V conversion kit, and 3) rewiring result if this machine is the main motor and the elevation motor. A quali- not grounded correctly. fied electrician must inspect all electrical modifi- Make sure all electrical cir- cations before connecting to power. cuits are grounded befo

Summary of the content on the page No. 13

3. Remove the wiring box covers on the main 5. Replace the main motor relay (LR3D-3359 motor and elevation motor. 48/65A) with the relay from kit (LR3D-3355 30/40A) and set the dial to “33.” 4. Wire the main motor and elevation motor as shown on the diagrams on the inside of each 6. Replace any wire duct covers and motor wir- motor wiring box cover. (The circled refer- ing box covers you might have removed dur- ences on the diagrams represent labels on ing this procedure, and close the electr

Summary of the content on the page No. 14

SECTION 4: MACHINE FEATURES 1 6 5 4 3 2 Figure 7. Main view of machine features and controls. 4. Infeed Conveyor—Moves the board through Main Features the bandsaw blade during cutting. 5. Infeed Conveyor Engagement Lever— Allows the operator to stop and start the 1. Infeed Pressure Rollers—Maintain down- infeed conveyor while the blade is moving. ward pressure on the board to keep it sturdy during cutting. 6. Control Panel—The part of the resaw where the operator can control the starting and

Summary of the content on the page No. 15

7 9 12 13 8 11 10 Figure 8. Rear view of machine features and controls. 11. Return Conveyor—Allows the person 7. Main Motor—Powers the saw wheels for receiving the newly cut board to return it blade movement and drives the hydraulic to the operator without walking around the pump for conveyor movement. saw. 8. Dust Ports—Allows the resaw to be con- 12. Blade Tension Gauge—Shows the current nected to a dust collection system. blade tension. 9. Hydraulic Pump—Creates hydraulic oil flow 13.

Summary of the content on the page No. 16

F. MOTOR STOP Button—Stops the main Control Panel motor, blade, and conveyors. G. DOWN Button—Moves the head (blade) down toward the infeed conveyor. N H. UP Button—Moves the head (blade) up A toward the infeed conveyor. I. Memory Button—Moves blade to a preset height change. For example, if you want to 1 B produce multiple ⁄4" boards from a 5" board, 1 you can set the memory to X inches (X= ⁄4" + your blade kerf). After every cut, the head C M will automatically move down X inches whe

Summary of the content on the page No. 17

SECTION 5: SET UP About this Section Piece Inventory After all the parts have been removed from The purpose of this section is to guide you the shipping crate, you should have: through the required steps to get your machine out of its crate and into operating condition. • Resaw Bandsaw Machine • Bandsaw Blade 180" x 1" x 0.035" • Tool Box • T-Handle Wrench 19mm This machine presents • 7 pc. Combination Wrench Set serious injury hazards —10, 12, 13, 14, 17, 19, 21 mm to untrained users.

Summary of the content on the page No. 18

Hardware Recognition Chart -16- G0504 16" Horizontal Resaw Bandsaw

Summary of the content on the page No. 19

Clean Up Site Considerations The unpainted surfaces are coated with a waxy 1. Floor Load: The Model G0504 represents oil to protect them from corrosion during ship- a large weight load. Most commercial floors ment. Remove this protective coating with a sol- are suitable for your machine. Some resi- vent cleaner or citrus-based degreaser such as dential floors may require additional build up to support both the machine and operator. Grizzly’s G7895 Degreaser. To clean thoroughly, some parts m

Summary of the content on the page No. 20

Removing Resaw Mounting Resaw to from Crate Pallet the Floor Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may The Model G0504 is a vary, floor mounting hardware is not included. heavy machine that weighs approximately Bolting to Concrete Floors 3300 lbs. Serious per- sonal injury may occur if Lag shield anchors with lag bolts and anchor safe moving methods are studs (Figure 12) are two popular me


Alternative user manuals
# User manual Category Download
1 Grizzly 50/65 Ton Ironworker G0646 User manual Saw 3
2 Grizzly DURASPIN DS275-18V User manual Saw 1
3 Grizzly G0444 User manual Saw 1
4 Grizzly Contractor Style G0732 User manual Saw 0
5 Grizzly BT-160X User manual Saw 1
6 Grizzly DURASPIN DS300-AC User manual Saw 0
7 Grizzly G0444Z User manual Saw 2
8 Grizzly G0460/G0461 User manual Saw 4
9 Grizzly Air Cut-Off G8122 User manual Saw 0
10 Grizzly 50/65 Ton Ironworker G0647 User manual Saw 0
11 Grizzly G0457 User manual Saw 0
12 Grizzly G0460 User manual Saw 0
13 Grizzly G0461 User manual Saw 3
14 Grizzly G0451 User manual Saw 3
15 Grizzly G0501 User manual Saw 0
16 Sony XS-L12S User manual Saw 8
17 Sony XS-L10S User manual Saw 1
18 3Com 3CRWDR200A-75 User manual Saw 6
19 Agilent Technologies 16193A User manual Saw 4
20 Aiphone AP-10M User manual Saw 1