Summary of the content on the page No. 1
Owner’s Manual
MEDIAMASTER
9660S
Summary of the content on the page No. 2
MEDIAMASTER 9660S Contents Volume level 16 FOR YOUR SAFETY 4 List of TV channels 16 Rear panel 4 List of Radio channels 17 Front panel 5 Video recorder 17 INSTALLATION OF THE MEDIAMASTER 5 Subtitling and Teletext. The TEXT Button 17 Connecting the Mediamaster to the SETTING FROM THE MAIN MENU 17 satellite dish 6 TV channels and radio channels 18 Connecting the Mediamaster to a
Summary of the content on the page No. 3
Keep a clear space around the Mediamaster to allow for sufficient ventilation. Do not cover the Mediamaster or place it on a unit that emits heat. Use a soft cloth and a mild solution of dish washing liquid to clean the casing. Never allow liquids, spray or other materials to come into contact with the inside of the Mediamaster. Service should be carried out only at a Nokia authorized service center. Do not connect or modify cables when the Mediamaster is plugged in. Do n
Summary of the content on the page No. 4
Front panel Display Slot Shows channel number, remote control For a two CA signal and time in standby mode. Module With a At start up, it displays the model number. Smartcard Power Up/Down To turn the receiver Select channel number, on/off (standby). up/down. INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: Mediamaster 9660S includes Power cable SCART Cable RCA cable
Summary of the content on the page No. 5
Connecting the Mediamaster to the satellite dish Installing the satellite dish Your satellite dish should be installed with a cable for you to connect to the Mediamaster. If you do not have this cable you will need to buy one from a dealer (tell the dealer you need a coaxial cable and F-connectors). Connect the cable from the satellite dish to the socket marked ”LNB IN” on the back of the Mediamaster. If you need to fit the F-connectors onto the cable 15 mm Prepare each
Summary of the content on the page No. 6
Connecting to a TV and a Video recorder Refer to your video recorder manual for full instructions. Connect one SCART cable between the main SCART socket on the TV and the TV SCART socket on the Mediamaster. Connect another SCART cable between the VCR and the VCR SCART socket on the Mediamaster. Connect the RF cable from the RF output on the VCR to the TV aerial input on the TV. Connect the TV aerial to the RF input socket on the VCR. If Your VCR does not have a SCART connector
Summary of the content on the page No. 7
Connecting to Hi Fi system Connect an RCA/Cinch stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE, AUX, SPARE or EXTRA input sockets on your Hi Fi system. Preparing the remote control Remove the cover on the battery compartment at the bottom of the remote control handset. Insert the 2 x AAA (1,5 V) batteries, as shown in the diagram, taking care to observe the + and - markings indicated inside. Replace the cover. Before you continue
Summary of the content on the page No. 8
About the Smart Card and CA Module. To be able to receive scrambled digital satellite channels you will need a Common Interface CA (Conditional Access) module and a smartcard from a Service Provider. It is possible to use two CA modules. The Service Provider is the programme distributor. If you are subscribing to services from more than one Service Provider, you might have to change between different Smart-cards and/or CA modules. Please note that a Smartcard and CA module may only
Summary of the content on the page No. 9
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. To switch the Mediamaster in and out of standby mode. EXIT TV To return to the viewing mode from a menu without storing settings (in menu mode). To switch between TV or Radio (in viewing mode). To turn the sound off/on (mute). To adjust the volume of digital programmes. The M
Summary of the content on the page No. 10
BASIC SETTINGS Once you have correctly connected the Mediamaster, you also have to perform some “Basic Settings”. During this procedure, helpful information is displayed at the bottom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process. However, and this is important, often more than one value has to be entered in a menu. First, perform all necessary settings on the diffe
Summary of the content on the page No. 11
The Welcome Menu To install the Mediamaster properly you have to adjust a few settings. You will always be guided by the information at the bottom of the menus. When you have finished the final part of the setup procedure you can start watching TV channels and listening to radio channels. Now you should have the “Welcome Menu” on the TV screen. Press the OK button to proceed. Language Settings Select the menu language that you desire. This will define the language shown in the me
Summary of the content on the page No. 12
Predefined Channel Select one of the predefined channel alternatives Predefined Channel. Adjust Motor Use the RIGHT / LEFT buttons to adjust the motor angle for selected satellite. During you adjust the motor by RIGHT of LEFT buttons, if you can find the AGC and BER level is full or higher level, stop the adjust the motor immediately. This red bar indicates the average strength of incoming signal for the selected satellite name. To accuracy alignment, push RIGHT / LEFT buttons slightl
Summary of the content on the page No. 13
In order to keep the Mediamaster up-to –date, it will be possible to download new version of the system software via satellite and from the internet. New software may include new or improved features for existing menus. Enter this menu to check for new software. If new software is available you will get information in the menu on how to proceed. If you download new software from “Nokia Internet pages”, you transfer the software from the computer to the Mediamaster via the serial po
Summary of the content on the page No. 14
You can enter a special LNB frequency, which is not presented in the LNB Type list as above. 22KHz Tone Switch: If you have connected to a Dual LNB or two antennas connected to a 22KHz tone switch box, set it to “Enable” the 22KHz tone switch. When you have finished the settings in this menu, press the “OK” button to save the parameter. Press BACK to continue with the channel search set-up (You can also recall this menu later. From the Main Menu; select “Installation” and then “Antenn
Summary of the content on the page No. 15
corresponds to the antenna which you wants to use for the search. Transponder Freq (MHz): Specify the frequency in GHz. using the numbered buttons on your remote control. If you enter the wrong number, erase it with the left arrow button. Polarization: Select polarization; “Horizontal” or “Vertical”. Symbol Rate (Msym/S): Enter the rate with the numbered buttons. FEC: Enter the appropriate Forward Error Correction (FEC) value or select “Auto”. Network Search: Select: “Yes” to search fro
Summary of the content on the page No. 16
Start/Stop Watching TV To start the Mediamaster from stand-by mode, press the “ ” button or one of the numbered buttons on the remote control. It is also possible to start by pressing the button on the front of the Mediamaster. Put the Mediamaster into stand-by by pressing again the “ ” button again. In stand-by mode the display will show the correct time. During viewing the channel number will also be displayed. Select Channel Change channel with the numbered buttons or with the up
Summary of the content on the page No. 17
The display on your Mediamaster and on the TV screen will show the name of the audio channel you are listening to. While in audio mode, you can press the “i” button to get extended information (if transmitted) about the audio programme. Return to TV mode by pressing the TV button again. Increase or decrease the sound level by pressing the “+” and “-” buttons. A control bar will be displayed at the top of the screen during level adjustment. (The max. level for volume is the curren
Summary of the content on the page No. 18
To watch TV programmes again, press the TV button or stop the VCR. Please note, that during the recording of a programme, everything shown on the screen will be registered! For example: If you call up a Menu from the Mediamaster on the screen, the menu will be recorded! Subtitling and Teletext. The TEXT Button Pressing the TEXT button once while watching TV enables the teletext output to the TV. To enable the teletext display on the TV, press the Teletext button on the TV’s rem
Summary of the content on the page No. 19
TV Guide and Radio Guide These guides will give you an overview of programme information from the TV/Radio channels. Step to different channel numbers with the UP/DOWN buttons. If you stop on a highlighted line and press OK, you will exit the menu and enter the highlighted channel. Select information about the next programme with the RIGHT button. Use the “i” button to get extended information about a marked programme. Please note, that information will only be shown if it is included
Summary of the content on the page No. 20
Add Channels From here you can create your own favorite lists, containing the channels you watch most frequently. You can give each list a specific name in the “Rename List” menu. When a favorite list is selected, you see only those channels defined in the list. You can add channels to your Favorite Lists from the “All TV”, “All Radio”, “Free TV” and “Free Radio” list. A channel is added by pressing the OK button. The “V” marking to the right on a line contains added channels. You can
