Summary of the content on the page No. 1
HUMNO-F3FOXCI.300GB
Summary of the content on the page No. 2
** Thank you for purchasing a HUMAX Digital Satellite Receiver. Please read this user manual carefully, to be able to safely install, use and maintain the product at maximum performance. Keep this user manual next to your product for future reference. Throughout the whole manual, Note indicates additional product operation information to make the user aware of possible problems and information of any importance to help the user understand, use and maintain the installation. ** Dolby and the doub
Summary of the content on the page No. 3
** The product has been manufactured to satisfy international safety standards. Please read the following safety precautions and warnings carefully. ** • Disconnect the product from the mains before you start any maintenance or installation procedures. � Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock. � The product should not be exposed to liquid of any kind. In addition, no objects filled with liquid, such as vases, should be placed on the
Summary of the content on the page No. 4
** 1. Before Using the Product GB5 ** 1.1 Package Contents GB5 1.2 Front Panel GB6 1.3 Rear Panel GB7 1.4 Conditional Access GB8 1.5 Remote Control GB9 2. Setup GB11 ** 2.1 Connecting Antenna/TV/VCR GB11 2.2 Connecting Audio System GB12 2.3 Powering On GB13 3. Menu Map GB14 4. Searching Services GB16 ** 4.1 Antenna Setting GB16 4.2 Manual Search GB17 4.3 Satellite Setting GB18 4.4 Motor Limit Setting GB19 4.5 USALS Setting GB20 4.6 Automatic Search GB21 5. Basic Operation GB22 ** 5.1 Viewing Pro
Summary of the content on the page No. 5
** 6. Service List GB25 ** 6.1 Switching Services GB25 6.2 Organising Services GB26 6.3 Organising Favourite Services GB27 6.4 Organising Networks GB28 6.5 Deleting Satellites GB29 7. Programme Guide GB30 8. Setting Preferences GB32 ** 8.1 Parental Control GB32 8.2 System Setting GB32 9. System Information GB34 ** 9.1 Status GB34 9.2 Common Interface GB35 9.3 Default Setting GB35 10. Utility GB36 11. Software Update GB37 12. Troubleshooting GB39 13. Specification GB41 14. Service and Support GB4
Summary of the content on the page No. 6
** This chapter provides detailed instructions on the product and its accessories. 1.1 Package Contents When you unpack your package contents, make sure you have all the necessary items shown in the figure below. If any of the items are missing or damaged, please contact your product dealer for replacement. ** ** Remote Control Batteries User's Manual Scart Cable ** ** ** ** ** Note: The product image may differ from the actual product. GB 5
Summary of the content on the page No. 7
** 1.2 Front Panel ** ** 1. STANDBY Button 4. TV LED ** ** Switches between Operation and Standby modes. Green light is emitted when the product is in TV mode. ** ** 2. TV/RADIO Button 5. RADIO LED ** ** Switches between TV and Radio. Amber light is emitted when the product is in Radio mode. ** ** 3. CH-/CH+ 6. STANDBY LED ** ** Moves the TV/Radio service up/down. Red light is emitted when the product is in standby mode. ** 7. CI-MODULE SLOT ** A slot for a CI module with a Smartcard. Note: See
Summary of the content on the page No. 8
** 1.3 Rear Panel ** ** 1. LNB IN 6. VIDEO ** ** Connects to satellite antenna cable. Connects to your TV or VCR and outputs Video signals. ** ** 2. LNB OUT 7. AUDIO L/R ** ** Connects to other digital Set-Top Box. Connects to your TV or VCR and outputs Audio signals. ** ** 3. RS-232C 8. RF OUT ** ** Connects to your PC to update product’s software Connects the RF signal of the product to the RF input programme. jack on your TV. ** ** 4. TV SCART 9. RF IN ** ** Connects a TV SCART cable. Connect
Summary of the content on the page No. 9
** 1.4 Conditional Access ** Inserting Common Interface CI-Module ** Your receiver is equipped with a slot for Common Interface (CI). ** 1. Open the right-hand flap on the front panel of the product. 2. Insert the Smartcard into the CI module, and CI module into the slot. ** GB 8
Summary of the content on the page No. 10
** 1.5 Remote Control 1. SOURCE ** Selects the input source between TV and the product. ** 2. TV/RADIO ** Switches between TV and Radio. ** 3. NUMERIC BUTTONS ** Enter a TV/Radio service number or menu option number. ** 4. MENU ** Displays the main menu. ** 5. TIME - WHITE ** Displays the current time on the screen. To set the current time, refer to 8.2 System Setting. ** 6. ARROW BUTTONS ** Changes services or moves the cursor up, down, left or right in menu option. ** 7. i (INFORMATION) - RED
Summary of the content on the page No. 11
** 9. CH-/CH+ 17. ZOOM - BLUE ** ** Changes the service. Enlarges the picture. ** ** 10. RECALL 18. SUBTITLE - YELLOW ** ** Returns to the previous screen. Displays the subtitle language list where available. ** ** 11. FREEZE 19.V-/V+ ** ** Freezes the TV screen you are watching. Does not Adjusts the audio volume. ** cease audio. 20. MUTE ** ** 12. WIDE Mutes or unmutes the audio temporarily. ** ** Changes the Display Format. 21. UHF ** ** 13. STANDBY Displays the UHF menu. ** ** Switches betwee
Summary of the content on the page No. 12
** This chapter describes how to set up the product. Select the most appropriate procedure depending on your requirements. Before you connect the product to any other equipment, you must disconnect all equipments from their power sources. Note: If you encounter any problem when setting up the product, please contact your local product distributor. 2.1 Connecting Antenna/TV/VCR ** ** 1. Connect the Antenna to LNB IN of the product. 2. SCART cable or RCA cable is connected as in the figure above.
Summary of the content on the page No. 13
** 2.2 Connecting Audio System ** ** 1. Connect the optical S/PDIF terminal and Dolby Digital decoder to listen to higher quality sound. GB 12
Summary of the content on the page No. 14
** 2.3 Powering On ** 1. Connect the power cord of the product to a wall outlet. ** ** 2. Press the STANDBY button on the front of the product or the remote control. ** GB 13
Summary of the content on the page No. 15
** GB 14
Summary of the content on the page No. 16
** ** Menu structure varies according to an item and its operation. You can easily navigate the menu using the following instructions: ** 1. Press the MENU button to display the main menu screen. ** 2. Select the item you want using the button. ** 3. Press the OK button to move from a menu to a sub-menu. ** 4. Press the button to select option values. ** 5. Press the NUMERIC buttons to enter the option values. ** 6. Press the button to open the option list and press the EXIT button to close the
Summary of the content on the page No. 17
** When powering on your product for the first time after purchase, the Selecting Language screen is automatically displayed. Select your desired language using the button and press the OK button. Then the Antenna Setting menu will be displayed. The default PIN code is 0000. ** 4.1 Antenna Setting You can set antenna and LNB information to search services using Antenna Setting (MENU-INSTALLATION-SERVICE SEARCHING-ANTENNA SETTING). ** � Antenna Alternative: Select antenna alternative which has di
Summary of the content on the page No. 18
** 4.2 Manual Search You can search services of the selected satellite by transponders if you know the transponder information. ** � Antenna Alternative: Select antenna alternative which has different combinations of settings for search. Antenna Alternative 16 is predefined for SMATV. � Frequency: Enter transponder frequency. � Polarisation: Select the type of polarisation. � Symbol Rate: Select or enter transponder symbol rate. � FEC: Select FEC (Forward Error Correction). � Network Search: If
Summary of the content on the page No. 19
** 4.3 Satellite Setting This menu appears only when you enable Motorised System in Antenna Setting menu and press the OK button while Antenna Alternative in Manual Search menu is selected. ** � Satellite Name: Select a satellite to identify a motor antenna. If the desired satellite name is not listed, then select "OTHER". � Movement: In user mode, this is used to fine-tune the position of the motor. In installer mode, this is used to search for the position of the satellite manually. � Motor Co
Summary of the content on the page No. 20
** To initialise the satellite position saved at Motor Antenna, set DiSEqC Command Mode to "Installer", set "Motor Control" to "Reset", then press the OK button. You will see a warning message. To continue the procedure, press the OK button. To set the motor position for each satellite manually, select the Satellite Name, set DiSEqC Command Mode to "Installer", and then set Movement to one option among "East", "Stop", or "West". The motor starts moving. The level of signal strength and quality b
