Jet Tools 50 user manual

User manual for the device Jet Tools 50

Device: Jet Tools 50
Category: Router
Manufacturer: Jet Tools
Size: 0.25 MB
Added : 9/18/2013
Number of pages: 8
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Jet Tools 50. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Jet Tools 50.

For your convenience

If looking through the Jet Tools 50 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Jet Tools 50 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Jet Tools 50 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Jet Tools 50 User manual - Online PDF
Advertisement
« Page 1 of 8 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Jet Tools 50 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Jet Tools 50. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

OWNER’S MANUAL
XACTA FENCE II™ Commercial 30/50
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax 253-939-8001
www.jettools.com e-mail jet@jettools.com M-708950X 3/01

Summary of the content on the page No. 2

Important Information 2-YEAR JET offers a two-year limited LIMITED WARRANTY warranty on this product REPLACEMENT PARTS Replacement parts for this tool are available directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box. REPLACEMENT PART WARRANTY JET Equipment & Tools makes ever

Summary of the content on the page No. 3

XACTA FENCE II™ COMMERCIAL 30/50 Note: This manual also runs through the steps of installing the rails, and extension table. WARNING Disconnect the table saw from the power source before attempting any assembly or adjustment! Failure to comply may cause serious injury! Contents of the Shipping Containers Tools Required for Assembly & Adjustment 1 XACTA FENCE II™ 1 #3 Cross Point Screwdriver 1 Front Rail 1 7/16” Wrench 1 Rear Rail 1 1/2" Wrench 1 Guide Rail 1 Combination Square & Straight Edge 3

Summary of the content on the page No. 4

Assembly Note: To insure that you have 2. Place a leg bracket into the outboard end of the table. enough adjustment in the cursor during the final adjustments, at this time you should bolt the 3. Mark all holes to be drilled. guide rail to the front rail with two hex cap screws. Place the fence on the guide rail so that the cursor lines up at four inches. Measure 4. Pre-drill all marked holes with a 3/16” drill bit approximately 1/2” deep. Do not drill from the saw blade to the fence and adjust

Summary of the content on the page No. 5

Note: You may need to re-adjust the clamping Guide Rail Assembly pressure after aligning the fence. 1. Bolt the guide rail to the front rail with 1/4-20 x 3/4” hex cap screws 1/4" flat washers and 1/4" lock washers. Center the bolt heads in Clamping Pressure the slotted holes of the rail so you will have some lateral adjustment. The XACTA FENCE II™ has been adjusted at the factory to lock securely when the lock 2. Measure from the front of the guide rail to handle is pushed down. If adjustment i

Summary of the content on the page No. 6

90° ° ° ° to the Table 1. Place the fence on the saw table and lock it. 2. Place a square on the table next to the fence. The fence should be 90° to the table, Figure 6. 3. If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (A, Fig. 7) until the fence is 90° to the table. 4. Lock the fence and check the adjustment again. Cursor Adjustment 1. Disconnect the table saw from the power source. 2. Raise the saw blade above the tabletop. 3. Unlock the fence an

Summary of the content on the page No. 7

Parts List for the JET XACTA FENCE II™Commercial 30/50 Index Part No. No. Description Size Qty. 1..........XF-1................................. Side Plate...................................................... ...................................2 2..........XF2-2W ........................... Fence Body Assembly................................... ...................................1 3..........XF2-3............................... Pad Set ......................................................... .

Summary of the content on the page No. 8

Parts Breakdown 8


Alternative user manuals
# User manual Category Download
1 Jet Tools 30 User manual Router 0
2 Edelbrock 1801 User manual Router 4
3 Sony LF-V30 User manual Router 19
4 3Com 3C13840 User manual Router 0
5 3Com 3C13880 User manual Router 1
6 Agilent Technologies E6385A User manual Router 2
7 Amana Bit User manual Router 0
8 ADTRAN A2.03 User manual Router 0
9 Atech Tech LIBRA-02 HM User manual Router 0
10 Atech Tech LIBRA-04 M User manual Router 1
11 Atech Tech LIBRA-02 M User manual Router 4
12 Atlantis A02-RA111 User manual Router 2
13 Atlantis A02-RA141 User manual Router 1
14 Atlantis WebShare User manual Router 1
15 Atlantis Land A02-AP-W54 User manual Router 3