Summary of the content on the page No. 1
Summary of the content on the page No. 2
Congratulations Congratulations on the purchase of your state-of-the-art remote start and security system. Reading this Owner’s Guide prior to using your system will help maximize the use of your system and its many fea- tures. Please visit the below website: http://www.clifford.com – For general and additional guide information. For any additional ques- tions please contact your authorized Directed dealer or contact Di- rected at 1-800-753-0600. What you get Welcome to the best generation
Summary of the content on the page No. 3
Important information Government Regulations and Safety information Read the Government Regulations and Warning! Safety First sections of this manual prior to operating this system. Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose. Your Warranty Your system comes with a warranty. Please make sure you receive the warranty registration card and proof of purchase
Summary of the content on the page No. 4
Contents Getting Started .................................................................................................... 3 Keys to using this manual ...................................................................... 3 Remote Control ................................................................................................... 4 Using your System ............................................................................................... 6 Commanding the system ..................
Summary of the content on the page No. 5
Nuisance Prevention (NPC) ................................................................. 20 Remote Start Features ........................................................................................ 21 Pit Stop Mode ................................................................................... 21 Key Takeover..................................................................................... 21 Remote Start Safe-lock ..................................................................
Summary of the content on the page No. 6
Getting Started Keys to using this manual Specific actions (in bold type) and style conventions are used consis- tently throughout this manual, they are as follows: Press: implies pushing in and releasing a button. Hold: is used after Press actions when a button needs to be held in position for an extended period of time, typically several sec- onds. Italicized words denote section/sub headings in this guide and can be located through the table of contents. An asterisk (*) when used after
Summary of the content on the page No. 7
Remote Control Internal Antenna Transmit LED Command Buttons AUX Function Button Feature Description Internal Antenna Used for transmitting information Transmit LED Active when transmitting information Command buttons (4) Used to perform arming, disarming, auxiliary channel and remote start commands Function button Used to access function levels for commands, configuration menus for programming and Car Selection © 2010 Directed Electronics. All rights reserved. 4
Summary of the content on the page No. 8
Control Center Control button Antenna Status LED The Control Center, typically located on the upper part of the front windshield. It consists of: The In-vehicle system antenna. The Status LED, as a visual indicator of the system’s status. The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation. * See Remote and System Operations section for details. ** See Alarm Features for details. © 2010 Directed Electronics. All rights reser
Summary of the content on the page No. 9
Using your System Commanding the system Commands, Basic or Advanced, are used to activate system features and are performed by pressing one of the Command buttons. Basic commands control the most often used security and remote start fea- tures while Advanced commands control more specialized features. Confirmations for Basic or Advanced commands are indicated by siren chirps and parking light flashes. A description of each feature confirmation is found in the following Basic command and Advanc
Summary of the content on the page No. 10
Remote Control Command table Direct Access Level x 1 x 2 x 3 x 4 Button LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 Arm/Lock Silent Arm Sensor Sensor Silent Full Silent (Panic) Bypass Arm Arm Disarm/Unlock Silent Disarm Remote Valet Car Finder Remote Start Runtime Timer Start Smart Start Defogger Reset Aux/Trunk AUX 1 AUX 2 AUX 3 AUX 4 AUX Advance Level, Enter program- ming (8 sec) © 2010 Directed Electronics. All rights reserved. 7
Summary of the content on the page No. 11
Basic Commands (Direct Access) Arm Press and release The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once. If Valet mode* is On, the doors lock without siren chirps, the alarm is disabled. Exit Valet mode to arm the alarm normally. If a trigger zone fault is detected the siren chirps once again and the control center LED generates a Trigger Zone Fault report**. To Arm and Panic Press and hold The alarm Arms (or Locks in Valet) and, after 2 seconds
Summary of the content on the page No. 12
Remote Start Press and release Activates (or if On, deactivates) the remote starter. The engine and parking lights turn On, or the engine and parking lights turn Off ac- cordingly. If a Remote start configuration issue prevents the engine from starting, the parking lights flash a Remote Start fault report*** to identify the fault. AUX/Trunk Press and hold AUX The Trunk opens (if connected) when this button is pressed for 2 sec- onds. * See Remote and System Operations for details. ** Se
Summary of the content on the page No. 13
Advanced Commands: (Level 1) Press and release the button 1 time. The transmit LED illuminates in sets of single flashes to indicate Level 1. Silent Arm Press and release The alarm arms, doors lock (if connected), and the parking lights flash once. Silent Disarm Press and release The alarm disarms, doors unlock (if connected), and the parking lights flash twice. The Silent Disarm output may be replaced by the Alarm Report* Runtime Reset Press and release If more time is needed while remote
Summary of the content on the page No. 14
Advanced Commands: (Level 2) Press and release the button 2 times. The transmit LED illuminates in sets of double flashes to indicate Level 2. Sensor Bypass Press and release Performing the Sensor Bypass command will incrementally bypass sen- sor operations and be confirmed as follows: Warn-away bypass: The Parking lights flash 2 times. Sensors will be activated for Full Trigger levels of impact only. Warn-away & Full trigger bypass: The Parking lights flash 3 times. Sensors will not be acti
Summary of the content on the page No. 15
Timer Start* Press and release Activates (or if On, deactivates) Timer Start. The parking lights flash quickly four times for On and slowly four times for Off. Note System needs to be armed or Timer Start will not start the engine. AUX 2 Press and release AUX Activates (or if On, deactivates) the Aux 2 output. * See Advanced Start under Remote Start Features for more details. © 2010 Directed Electronics. All rights reserved. 12
Summary of the content on the page No. 16
Advanced Commands: (Level 3) Press and release the button 3 times. The transmit LED illuminates in sets of triple flashes to indicate Level 3. Sensor Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 3 times. Car finder Press and release The siren emits one long chirp and the parking lights flash for 10 sec- onds. The parking light flashes stop if armed or disarmed while Car Finder is in progress. Smart Start** Press and release Activates (
Summary of the content on the page No. 17
Advanced Commands: (Level 4) Press and release the button 4 times. The transmit LED illuminates in sets of quadruple flashes to indicate Level 4. Full Silent Arm* Press and release The alarm arms, doors lock, and the siren chirps and parking lights flash 4 times. Defogger** Press and release Activates the vehicle Defogger circuit (if connected) while Remote Start is activated and the parking lights flash 3 times. For convenience, the Defogger circuit will also automatically activate 10 secon
Summary of the content on the page No. 18
Remote Control Configuration Remote Programming The remote controls have operations that can be configured to a user’s personal preferences. The following instruction will direct you through the available programming options for both remote controls. Enter programming, press and hold the button for 8 seconds, the transmit LED turns on to indicate the Main Menu is accessed. Exit programming or go back to a previous menu, press and release the button. When programming is exited the transmit LED
Summary of the content on the page No. 19
Prepare the remote control for pairing: 6. Enter programming to access the Main Menu 7. Press and hold the button for 1 second, 3 transmit LED flash- es indicate the remote control is ready to pair. 8. Press the button, The siren will chirp to confirm the system has learned the remote con- trol. Remote Features From the main menu, press the button to access the remote opera- tion features, 2 transmit LED flashes indicate the remote features menu is accessed. Press the buttons indicated in the
Summary of the content on the page No. 20
To unlock the buttons, press the button followed by the button. Note When the Keypad is locked, the remote control may ap- pear to be non-operational. It will not transmit a command or illuminate the Transmit LED and needs to be unlocked to resume normal operation. Car 2 Options: Off, On The remote controls can control two systems independently. When set to Off, the Car Select feature is not available. When set to On the Car Select feature is enabled. See Car Select (un- der Remote and Sy
