Summary of the content on the page No. 1
Model 3100L
➤Owners Guide
Summary of the content on the page No. 2
Limited Lifetime Consumer Warranty For a period of one calendar year from the date of purchase of this auto-security device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model), free of cost, any electronic control module which proves to be defective in workmanship or material under normal use, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYST
Summary of the content on the page No. 3
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUD- ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM- MERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLU- SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WAR- RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREW
Summary of the content on the page No. 4
This vehicle theft protection is effective for one (1) year from the date of purchase and is limited to one claim. This vehicle theft protection guarantee is valid only for the theft of the entire vehicle and specifically excludes any other considerations, including, but not limited to, damage caused to the vehicle, theft of parts, contents or any other consequential damages. Once Avital Technologies verifies that all the above listed terms and conditions have been met, a check for the insurance
Summary of the content on the page No. 5
Table of Contents Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Your Warranty . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
2 2008 Directed Electronics ©
Summary of the content on the page No. 7
What is Included ■ A control module ■ Two 3-button remote transmitters ■ A zone 2 impact sensor on-board the control module ■ A high-powered siren ■ A fault-proof starter interrupt on-board the control module ■ An LED system status indicator ® ■ A push-button Valet switch Important Information Congratulations on the purchase of your state-of-the-art vehicle security system. This system has been designed to provide years of trouble-free operation. By carefully reading this guide prior to using
Summary of the content on the page No. 8
when using the remote transmitter. To access the battery for replacement, remove the rear cover of the remote with a small, flat-blade screwdriver. Your Warranty Your warranty card must be returned and the barcode serial num- ber must not be removed. If the warranty card is not returned, no warranty will be honored on your unit. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. Make sure you receive the war- ranty card fro
Summary of the content on the page No. 9
Remote Functions This system is programmable, making it possible to assign any remote button to any specific receiver function. The remote initial- ly comes programmed with Standard Configuration, but may also be customized by an authorized dealer. The buttons in all of the instruc- tions in this manual correspond to a Standard Configuration remote. Standard Configuration Button The arm/disarm/panic functions are usually controlled by . Button An optional accessory function (such as trunk releas
Summary of the content on the page No. 10
Using Your System The remote buttons indicated in this manual correspond to a stan- dard configuration remote, unless otherwise specified. Arming You can arm the security system by pressing for one second. When the system arms, you will hear a short siren sound (chirp) and the parking lights will flash once. If the power door locks are controlled by the system, the doors will also lock. Once armed, the LED system status indicator will flash once per second to indicate that the system is activel
Summary of the content on the page No. 11
time a sensor is triggered during the Passive Arming countdown, the countdown starts over. Arming your security system protects your vehicle to the following degrees: ■ Light impacts trigger a warn-away response, causing the siren to chirp and the parking lights to flash for a few seconds. ■ Heavy impacts trip a trigger sequence, which consists of the siren sounding continuously and the parking lights flashing for 30 seconds. ■ If a door is opened, the siren immediately starts chirping and the
Summary of the content on the page No. 12
disarming indicates Tamper Alert, which is described in the Diagnostics section of this guide. Disarming Without a Remote If your remote is lost or damaged, you can manually disarm your vehicle security system. To disarm the system without a remote, you must have the vehicle's ignition key and know where the Valet switch is located. Be sure to check with your installer at the time of installation for the location of the Valet switch. To disarm the security system, turn the ignition key on and p
Summary of the content on the page No. 13
Remote-Controlled Silent Arm/Disarm Use remote-controlled silent arm/disarm to temporarily turn off the arm or disarm chirps by briefly pressing before either arming or disarming. The confirmation chirp(s) will then be elimi- nated for that one operation only. To permanently turn off the arm and disarm chirps, contact your installation dealer. NOTE: The warn-away response to lighter impacts is bypassed if the system is armed using remote-controlled silent arm/disarm. This ensures that the sire
Summary of the content on the page No. 14
Remote-Controlled Valet You can also enter or exit Valet Mode by using the remote: 1. Open any vehicle door. 2. Press . 3. Press . 4. Press again. The LED system status indicator will light solidly if you have entered Valet Mode and will turn off if you have exited Valet Mode. ® Nuisance Prevention Circuitry ™ ™ Your security system has Nuisance Prevention Circuitry (NPC ) to prevent annoying false alarms. This circuitry is designed to prevent repetitive trigger sequences due to faulty door pi
Summary of the content on the page No. 15
rity system is triggered by an open door for three, full 30-second cycles (one and one half minutes), the system will bypass the doors until the trigger ceases. ™ NOTE: Arming and disarming the system does not reset the NPC . The only ways to reset a bypassed zone are for that zone not to be triggered for 60 minutes or to turn the ignition key on. When testing your system, it is important to remember that NPC™ can cause zones to be bypassed and appear to not work. If five chirps are heard when d
Summary of the content on the page No. 16
your vehicle has an interior light exit delay and you arm the sys- tem before the light turns off, you may hear a Bypass Notification chirp. Three seconds after the light turns off, however, normal monitoring resumes. NOTE: Bypass Notification does not occur when the system is in remote- controlled silent arm/disarm mode or if the chirps have been programmed not to sound. Disarming Diagnostics Your system has a Tamper Alert feature that notifies you of system triggers that occur while you are aw
Summary of the content on the page No. 17
ZONE (Number of DEALER-INSTALLED LED Flashes) DESCRIPTION OPTIONS 1 Instant trigger for optional sensor, hood or trunk pins 2 A heavier impact detected by the on-board impact sensor 3 Door switch trigger 5 Ignition trigger NOTE: The LED does not report when the warn-away response has been activated; it only reports triggered sequences. Code Hopping Technology The receiver and remote use mathematical formulas called algo- rithms to change their codes each time the remote is used. This Code H
Summary of the content on the page No. 18
High Frequency Your system transmits and receives at 434 MHz. This provides a cleaner spectrum with less interference and a more stable signal. Enjoy a phenomenal increase in range, even in areas with high radio interference. Programming Options Programming options control your system's normal, operational set-up. Most options do not require additional parts, but some may require installation labor. This system's programming options are listed below, with the fac- tory default settings in bol
Summary of the content on the page No. 19
key is turned on, and unlock when the ignition is turned off. The system also prevents the doors from locking when the ignition is turned on while any vehicle door is open. Security & Convenience Expansions Listed below are some of the many expansion options available for use with your system. Please consult your dealer for a detailed explanation of all the available options. Audio Sensor: Metal on glass, glass cracking, and breaking glass produce distinctive acoustic signatures. The 506T audio
Summary of the content on the page No. 20
Power Trunk Release: The output of the system can operate a factory power release for the vehicle's trunk or hatch. An optional relay is required. If the factory release is not power-activated, then DEI's 522T trunk release solenoid can be added in most cases. Power Window Control: Automatic power window control is pro- vided with the 529T and 530T systems. These options operate power windows, by rolling them up, down, or both up and down. The 530T also offers one-touch switch operation. ™ Valet
