Summary of the content on the page No. 1
Model 4113
Remote Start
Owner’s Guide
© 2009 Directed Electronics, Vista, CA
G4113L 2009-05
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Contents Government Regulations ....................................................................................5 Warning! Safety first .........................................................................................6 What is Included ............................................................................................8 Important Information ........................................................................................8 System Maintenance ........................
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga
Summary of the content on the page No. 6
Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control remote control. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially encl
Summary of the content on the page No. 7
After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All in
Summary of the content on the page No. 8
What is Included • The control module • An HX receiver/antenna • Two 1-button remote controls (P/N 7111L) • A push-button programming switch • Your warranty card • A shut-down toggle switch Important Information Congratulations on the purchase of your remote start keyless entry sys- tem. This system has been designed to provide years of trouble-free operation. By carefully reading this owner’s guide prior to using your system, you will maximize the use of this system and its features
Summary of the content on the page No. 9
Using Your System ➢ Unlocking Only after the vehicle is remotely started via the remote control, press and release the remote control button for 1 second to unlock the ve- hicle’s doors. The parking lights will flash and the horn will honk twice to confirm unlock. Note: Horn honk is an optional feature. ➢ Car Finder Press and hold the remote control button for 3 seconds to activate the car finder function (parking lights flash 5 times slowly). The remote start must not be activated for Car
Summary of the content on the page No. 10
➢ Ignition Controlled Door Locks If power door locks have been connected to your system, the vehicle's doors will lock three seconds after the ignition has been turned On and unlock when the ignition is turned Off. Important: In order for the ignition controlled door locks to work the feature must be programmed On. If the ignition is turned on when the vehicle is remote started the doors will not lock until the remote start shuts off. To avoid being locked out of the vehicle, do not turn th
Summary of the content on the page No. 11
➢ Remote Start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle. Important! (1) Never remotely start the vehicle with the vehicle in gear,
Summary of the content on the page No. 12
While the vehicle is running during remote start operation, the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut-down inputs: • Brake pedal is pressed. • Hood is opened. • Shutdown toggle switch is put into the ON position. • Pre-programmed run time has elapsed. • Remote control button is pressed and held for 3 seconds. ➢ Valet Take-Over The Valet Take-Over feature allows the vehicle to remain running after the
Summary of the content on the page No. 13
➢ Starter Anti-Grind Circuitry Whenever the vehicle is remote started, advanced anti-grind circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation. Note: Anti-grind circuitry only works when the remote start system is op er at ing the motor and the optional relay is installed. ➢ Disabling the Remote Start System This feature allows your sys
Summary of the content on the page No. 14
Rapid Resume Logic This Directed Electronics system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Locked Mode and the battery is dis connect ed for any reason, such as servicing the car, when the battery is recon nect ed the unit will still be in Locked Mode. This applies to all states of the system. © 2009 Directed Electronics. All rights reserved. 14
Summary of the content on the page No. 15
Programming Options Programming options control your system's normal operational set-up. Most options do not require additional parts, but some may require installation labor. The following is a list of the programmable options, with the factory settings in bold. • 12, 24, or 60 minute run time. Your system can be programmed to allow the vehicle to run for 12, 24, or 60 minutes when remote started. Can be set up to minute increments by your installer. • Parking lights flashing or constant.
Summary of the content on the page No. 16
Glossary of Terms Control Unit: The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which moni- tors your vehicle and controls all the system functions. Remote control: A hand-held device control that operates the various functions of your system. LED: Indicator on your remote control when a button is pressed. © 2009 Directed Electronics. All rights reserved. 16
Summary of the content on the page No. 17
✂ Quick Reference Guide To remote start the vehicle • Press and release the remote control button for 1-second. The park- ing lights will turn on constant to confirm remote start operation. To shut down remote start • Press and hold the remote control button for 3 seconds. The park- ing lights will turn off. Car finder (remote start must not be active) • Press and hold the remote control button for 3-seconds. The park- ing lights will start to flash 5 times slowly. To unlock the doors (remote
Summary of the content on the page No. 18
Notes © 2009 Directed Electronics. All rights reserved. 18
Summary of the content on the page No. 19
© 2009 Directed Electronics. All rights reserved. 19
Summary of the content on the page No. 20
