Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS
30" (76.0 CM) FREESTANDING ELECTRIC RANGES
Table of Contents
RANGE SAFETY .............................................................................1 INSTALLATION INSTRUCTIONS ..................................................4
Unpack Range..............................................................................4
INSTALLATION REQUIREMENTS ................................................2
Install Anti-Tip Bracket...................................................
Summary of the content on the page No. 2
INSTALLATION REQUIREMENTS IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used Tools and Parts will not discolor, delaminate or sustain other damage. This oven Gather the required tools and parts before starting installation. has been designed in accordance with the requirements of UL Read and follow the instructions provided with any tools listed and CSA International and complies with the maximum allowable here. wo
Summary of the content on the page No. 3
Electrical Connection Cabinet Dimensions To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions Cabinet opening dimensions shown are for 25" (64.0 cm) provided for it here. countertop depth, 24" (61.0 cm) base cabinet depth and ■ Range must be connected to the proper electrical voltage 36" (91.4 cm) countertop height. and frequency as specified on the model/serial number rating IMPORTANT: If installing a range hood
Summary of the content on the page No. 4
The fourth (grounding) conductor must be identified by a green or If connecting to a 3-wire system: green/yellow cover and the neutral conductor by a white cover. Local codes may permit the use of a UL listed, 3-wire, 250-volt, Cord should be Type SRD or SRDT with a UL listed strain relief 40- or 50-amp range power supply cord (pigtail). This cord and be at least 4 ft (1.22 m) long. contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating
Summary of the content on the page No. 5
Install Anti-Tip Bracket Floor Mounting WARNING A B Tip Over Hazard A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults. A. #12 x 1⁵⁄₈" screws B. Anti-tip bracket 1. Remove the anti-tip bracket that is taped in the storage Wall Mounting drawer. 2. Determine which mounting method to use: floor or wall.
Summary of the content on the page No. 6
Electrical Connection Power Supply Cord Direct Wire WARNING WARNING Electrical Shock Hazard Electrical Shock Hazard Disconnect power before servicing. Disconnect power before servicing. Use a new 40 amp power supply cord. Use 8 gauge copper or 6 gauge aluminum wire. Plug into a grounded outlet. Electrically ground range. Failure to follow these instructions can result in death, Failure to follow these instructions can result in death, fire, or electrical shock. fire, or electrical shock. 1. Dis
Summary of the content on the page No. 7
■ Position cord/conduit plate as shown in the following Electrical Connection Options illustration. If your home has: And you will be Go to Section: connecting to: 4-wire receptacle A UL listed, 4-wire connection: (NEMA type 14-50R) 250-volt Power supply cord B minimum, A 40-amp, range A. Small opening power supply B. Large opening cord ■ Replace cord/conduit plate and insert screws. 4-wire direct A fused 4-wire connection: disconnect or Direct wire circuit breaker 5" box (12.7 cm) 3-wire
Summary of the content on the page No. 8
3. Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to 3-wire connection: Power Supply Cord easily attach the wiring to the terminal block. Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord. A 1. Feed the power supply cord through the strain relief on the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal blo
Summary of the content on the page No. 9
3. Pull the conduit through the strain relief on cord/conduit plate Direct Wire Installation: Copper or Aluminum Wire on bottom of range. Allow enough slack to easily attach wiring to the terminal block. This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection. A 1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire
Summary of the content on the page No. 10
6. Use ³⁄₈" nut driver to connect the neutral (white) wire to the 2. Attach terminal lugs to line 1 (black), bare (green) ground, and center terminal block post with one of the #10-32 hex nuts. line 2 (red) wires. Loosen (do not remove) the set screw on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten set screw to torque as shown in the following Bare Wire Torque Specifications chart. G A A B B F D E C C DE A. #10-32 hex nut E. Neut
Summary of the content on the page No. 11
Verify Anti-Tip Bracket Location Complete Installation 1. On models with a storage drawer, pull drawer open to first 1. Check that all parts are now installed. If there is an extra part, stop position. Lift front of drawer to clear white wheels in go back through the steps to see which step was skipped. drawer guides. Remove drawer and set it aside on a covered 2. Check that you have all of your tools. surface. 3. Dispose of/recycle all packaging materials. On models with a warming drawer, the
Summary of the content on the page No. 12
Moving the Range For direct-wired ranges: WARNING WARNING Tip Over Hazard Electrical Shock Hazard Disconnect power before servicing. A child or adult can tip the range and be killed. Connect anti-tip bracket to rear range foot. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death 1. Disconnect power. or serious burns to children and
