Summary of the content on the page No. 1
Table of Contents
1. Precautions for safety and use_________________________ 4
2. Fitting the appliance in the top _________________________ 5
2.1 Fixing to the supporting structure ________________________________________5
3. Electrical connection ________________________________ 7
4. Gas connection ____________________________________ 8
4.1 Bottled gas connection ________________________________________________9
4.2 Room ventilation___________________________________________________
Summary of the content on the page No. 2
Precautions for Safety and Use 1. Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AN
Summary of the content on the page No. 3
Instructions for the Installer 2. Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and/or joiner. The hob can be installed on various materials, including masonry, metal, solid wood and wood finished with plastic laminates, provided the material is heat-resistant (T 90° C). 2.1 Fixing to the supporting structure Make a hole in the cabinet top with the dimensions shown here, maintaining a distance of at least 50 mm fr
Summary of the content on the page No. 4
Instructions for the Installer Fit the insulating gasket provided carefully around the outside edge of the hole made in the top as shown below, pressing it down with your hands so that its entire surface fits snugly. Follow the dimensions shown, depending on the model of hob to be installed, bearing in mind that on both models the long front edge must be flush with the hole. Fix the hob to the structure using the brackets A provided. Carefully trim off the excess edge of the gaske
Summary of the content on the page No. 5
Instructions for the Installer 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that
Summary of the content on the page No. 6
Instructions for the Installer 4. Gas connection If the appliance is installed above an over, the gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains may be made using a copper pipe or a continuous-wall steel hose in accordance with the relevant regulations. To simplify connection, the horizontal position of the fitting A on the back of the appliance is adjustable. Undo the hexagonal nut B, turn the fitting A into the requi
Summary of the content on the page No. 7
Instructions for the Installer 4.1 Bottled gas connection Use a pressure regulator and make the connection to the gas cylinder in accordance with the relevant regulations. Make sure that the gas supply pressure is as stated in the table in point "5.2 Adjusting for bottled gas". 4.2 Room ventilation The appliance may only be installed in a permanently ventilated room as specified by the relevant regulations. The air flow into the room where the appliance is installed must be suffici
Summary of the content on the page No. 8
Instructions for the Installer 5. Adapting to different types of gas Before carrying out the operations described below, disconnect the appliance from the electricity supply. The hob is tested with G20 (2H) natural gas at the pressure of 20 mbar. If it is to be used with other types of gas, the burner nozzles have to be changed and the primary air flow adjusted. To replace the nozzles and adjust the burners, the hob plate has to be removed as described below. 5.1 Removi
Summary of the content on the page No. 9
Instructions for the Installer 5.2 Adjusting for bottled gas Undo the screw A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm. Return the support B to its original position, so that the nozzle C is perfectly covered. Regulate the air flow by moving the Venturi pipe D until the distance “X” st
Summary of the content on the page No. 10
Instructions for the Installer 5.5 Adjusting the primary air flow Refers to the gap “X” in mm. BURNER G30/G31 G110 G20 30/37 mbar 8 mbar 20 mbar Semi rapid (1) 10.0 1.5 2.0 8.0 1.5 2.5 Rapid (2) 12.0 5.0 2.5 Ultra-Rapid (3) To identify the burners on your hob, refer to the drawings in point “5.8 Hob burner layout” 5.6 Reassembling the hob skin Reverse the procedure described in point “5.1 Removing the hob skin ”. When replacing the burner rings, bear in mind t
Summary of the content on the page No. 11
Instructions for the Installer 5.9 Hob burner layout Burner type 1 Semi rapid 2 Rapid 3 Ultra-Rapid 5.10 Greasing the gas taps Over time, the gas taps may become stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician. 13
Summary of the content on the page No. 12
Instructions for the User 6. Description of controls 6.1 The front panel All the hob's control and monitoring devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum and the minimum settings. To turn off the burner, turn the knob back to the O position. BURNER LAYOUT - Key to symbol
Summary of the content on the page No. 13
Instructions for the User 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. 7.1 Lighting burners with safety device The burner it controls is shown next to each knob (the example here shows the front left-hand burner).
Summary of the content on the page No. 14
Instructions for the User 8. Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regularly, after each use, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning and caring for stainless steel surfaces, always use only specific products which do not contain abrasives or chlorine-based acids. Ins
Summary of the content on the page No. 15
Summary of the content on the page No. 16
914773119/ B
