Summary of the content on the page No. 1
thermaline S90
ELECTRIC INDUCTION RANGES
FOURNEAUX ÉLECTRIQUES À INDUCTION
US INSTALLATION- AND OPERATING INSTRUCTIONS page 3
FR INSTRUCTIONS D’INSTALLATION ET D’EMPLOI page 11
Doc. 62.9581.01_UL
Edition 1
01.2006
Summary of the content on the page No. 2
Against wall - contre une paroi Free standing - isolé Connections - Raccordement Gas - Gaz Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION Doc. 62.9581.01_UL
Summary of the content on the page No. 3
Free standing - isolé operated from both sides - ulilisable des deux côtés Connections - Raccordement Gas - Gaz Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION
Summary of the content on the page No. 4
Doc. 62.9581.01_UL
Summary of the content on the page No. 5
CONTENTS I GENERAL INFORMATION .................................................................................................3 II INSTALLATION INSTRUCTIONS .......................................................................................5 III OPERATING INSTRUCTIONS ............................................................................................9 SOMMAIRE IV INSTRUCTIONS GÉNÉRALES .........................................................................................11 V IN
Summary of the content on the page No. 6
Page 2 62.9581.01_UL
Summary of the content on the page No. 7
GENERAL INFORMATION I . GENERAL INFORMATION 1. INSTRUCTIONS FOR SAFETY AND USE 1.4 SAFETY-CONSCIOUS WORKING 1.1 INSTALLATION AND INITIAL OPERATION Touching the hotplates can cause burns. As soon as a crack in the surface becomes The installation, adjustment and initial visible, the equipment is to be disconnected operation of the appliance must be properly immediately from the power supply. carried out in accordance with the manufacturer's instructions and may only be Spraying the appl
Summary of the content on the page No. 8
GENERAL INFORMATION 2. TECHNICAL DATA Width Full sur- Power Depth face Voltage PNC Height cooking Appliance type Appliances zones V inch mm in kW 9CHG584126 WIWRAFQOOO 208 9CHG584127 WIXRAFQOOO 240 19.7 500 9CHG584128 WIWRAAQOOO 208 35.4 900 210 9CHG584129 WIXRAAQOOO 240 35.4 900 9CHG584130 WIWRABQOOO 208 9CHG584131 WIXRABQOOO 240 9CHG584132 WIWWAFQQOO 208 9CHG584133 WIXWAFQQOO 240 39.4 1000 9CHG584134 WIWWAAQQOO 208 35.4 900 420 9CHG584135 WIXWAAQQOO 240 35.4 900 9CHG584136 WIWWABQQOO 208 9C
Summary of the content on the page No. 9
INSTALLATION INSTRUCTIONS II . INSTALLATION INSTRUCTIONS 1. INSTALLATION 1.3 ASSEMBLING TWO APPLIANCES The appliance is designed for connection to fixed lines. The appliances are suitable for setting up as single appliances or as a group of appliances. They can be set up freely in the room, side by side, at the side and/or at the back against a wall. (3a) Gaps between two appliances or appliance and sidewall should be filled with a FDA approved silicone such as Samco (1) (2) RTV103. (3b) 1
Summary of the content on the page No. 10
INSTALLATION INSTRUCTIONS 1.4 SIDEWALL (D) 1.6 ASSEMBLING ON CASTORS () (5) (4) () (5) (4) 1 1 (3c) 1 a a b Fig.2 Assemblage of sidewall The assembly kit contains two of each of the following: (3c) hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings 1 (3c) 1 (2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16 with serrated washers and hexagonal nuts M8, hexagonal c screws M5 with serrated washers (4 / Fig.2) b and a fastening angle (5 / Fig.2). Fig.4 Assemblage on ca
Summary of the content on the page No. 11
INSTALLATION INSTRUCTIONS 2.1 FRONT PANELS (A) and (B) 3. DOWNPIPE (1) (3c) (1) 1 a b Fig.6 Front panel Unscrew screws (1 or 3). Also, in the case of a built-in oven, unscrew screws (2 and/or 4) on the inside of the oven. (3) Pull the panel away forwards and downwards. 2.2 CONTROL PANEL (C) Fig. 8 Downpipe (2) c (3c) (3c) Work surfaces with a downpipe (Fig.8a) have the downpipe (1) 1 1 opening on the right-hand side of the appliance. A flexible sili- con hose when installed in the standard
Summary of the content on the page No. 12
INSTALLATION INSTRUCTIONS 4.2 CONNECTION TO THE POTENTIAL 4. ELECTRICAL CONNECTION EQUALIZATION SYSTEM Each appliance is accompanied by a complete connection and The appliance is to be connected to a potential equalization wiring diagram enclosed. This contains full details of the system with a minimum conductor cross-section of 10 mm². technical specifications (electrical rating, voltage, amperage Use the appropriately marked terminal studs for this purpose etc.) (EN 60 335). The connection co
Summary of the content on the page No. 13
OPERATING INSTRUCTIONS III . OPERATING INSTRUCTIONS Cooking pans with a diameter of less than 6.3“ (16 cm) must 1. GENERAL not be used. The appliance is used for boiling, searing, cooking, keeping warm and preparation. Depending on the type of range, the Warning: glass ceramic plate is equipped with two or four rings with an • If unsuitable materials are used, the heating system electrical output of 3.5 KW or 5 KW each. does not function or the appliance may get destroyed. The individua
Summary of the content on the page No. 14
OPERATING INSTRUCTIONS Never use corrosive substances for cleaning the floor 6. STORAGE SPACE under the appliance (e.g. hydrochloric acid). Clean the The storage space (Fig.12) is incorporated into the base unit. appliance with commercial cleaning agents. Recommended accessories: 4. SHUTTING DOWN - Shelf holder (1) 2 off. - Shelves (2) 1 off. Never store the range where the temperature can drop below 32 °F (0 °C). Rub all chrome nickel steel surfaces with a cloth soaked in vaseline oil, to
Summary of the content on the page No. 15
INSTRUCTIONS GÉNÉRALES I . INSTRUCTIONS GÉNÉRALES 1. CONSIGNES DE SÉCURITÉ ET D'UTILISATION 1.4 TRAVAILLER EN TOUTE SÉCURITÉ On peut se brûler si l'on entre en contact avec 1.1 INSTALLATION ET MISE EN SERVICE les plaques chaudes. Le montage, le réglage et la première mise en Dès qu'une fissure est visible en surface, service de l'appareil doivent s'effectuer confor- débrancher immédiatement l'appareil du mément aux instructions du fabricant et être secteur. confiés exclusivement à un tec
Summary of the content on the page No. 16
INSTRUCTIONS GÉNÉRALES 2. DONNÉES TECHNIQUES Largeur Surface Puis- sance Profondeur Modèle Voltage Hauteur Appareil PNC de l'appareil V inch mm in kW 9CHG584126 WIWRAFQOOO 208 9CHG584127 WIXRAFQOOO 240 19.7 500 9CHG584128 WIWRAAQOOO 208 35.4 900 210 9CHG584129 WIXRAAQOOO 240 35.4 900 9CHG584130 WIWRABQOOO 208 9CHG584131 WIXRABQOOO 240 9CHG584132 WIWWAFQQOO 208 9CHG584133 WIXWAFQQOO 240 39.4 1000 9CHG584134 WIWWAAQQOO 208 35.4 900 420 9CHG584135 WIXWAAQQOO 240 35.4 900 9CHG584136 WIWWABQQOO 208 9
Summary of the content on the page No. 17
INSTRUCTIONS RELATIVES À L'INSTALLATION II . INSTRUCTIONS RELATIVES À L'INSTALLATION 1. MISE EN PLACE 1.3 ASSEMBLAGE DE DEUX APPAREILS Cet appareil est conçu pour être raccordé à des conduites fixes. Les appareils peuvent être montés individuellement ou en groupe. Ils peuvent être installés de façon indépendante, côte à côte, avec un côté et/ou la partie arrière de l'appareil (3a) reposant contre une paroi. Les interstices entre deux appareils ou entre un appareil et le (1) (2) mur latéral
Summary of the content on the page No. 18
INSTRUCTIONS RELATIVES À L'INSTALLATION 1.4 PAROI LATERALE (D) 1.6 ASSEMBLAGE SUR ROULETTES () (5) (4) () (5) (4) 1 1 (3c) 1 a a b Fig.2 Montage du paroi latérale Chaque kit d'assemblage comprend respectivement deux vis hexagonales M8 x 25 (1 / Fig.1), des boulons avec circlip (2 (3c) 1 (3c) / Fig.1), des éclisses (3 / Fig.1), des vis hexagonales M8 x 16 1 avec rondelles à denture intérieure et des vis hexagonales M8, des vis hexagonales M5 avec rondelles à denture intérieure (4 c b / Fig.1)
Summary of the content on the page No. 19
INSTRUCTIONS RELATIVES À L'INSTALLATION 3. SORTIE 2.1 PANNEAU AVANT (A) et (B) (3c) (1) 1 (1) a b Fig.6 Panneau avant Desserrez les vis (1 et 3 Fig.5, Fig.6). Si le four est (3) encastré, desserrez Extrayez le panneau vers l'avant et le bas. Fig.8 Sortie 2.2 PANNEAU DE COMMANDE (C) c (2) Les plans de travail avec sortie (fig. 8a) sont pourvus d'un ori- fice de sortie à droite de l'appareil. Un flexible en silicone (3c) (3c) installé en série débouche en bas à droite, 20 mm derrière le (1) 1
Summary of the content on the page No. 20
INSTRUCTIONS RELATIVES À L'INSTALLATION 4.2 BRANCHEMENT AU SYSTÈME ÉQUIPOTENTIEL 4. BRANCHEMENT ÉLECTRIQUE L'appareil doit être raccordé à un système équipotentiel dont la Chaque appareil est accompagné d'un schéma complet des 2 section du conducteur est d'au moins 10 mm . Pour ce faire, connexions et du câblage reprenant les données techniques utilisez les boulons identifiés à cet effet (EN 60 335). Le rac- (puissance électrique, tension, intensité de courant, etc.). cordement se compose d'un b
