Summary of the content on the page No. 1
OPERATING INSTRUCTIONS
WT-870
DIVERSITY WIRELESS TUNER
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
TOA Corporation
Summary of the content on the page No. 2
GENERAL DESCRIPTION Designed for virtual elimination of problem "null spots" or "dropouts" (momentary loss of radio signal reception), the TOA WT-870 is a diversity tuner that permits simultaneous use of up to two optional wireless tuner modules WTU-870 and WTU-871. To ensure its reliability, the WT-870 employs a compressor/expander system noise reduction circuit to minimize the influence of high-frequency noise generated from digital equipment such as personal computers and word processors as w
Summary of the content on the page No. 3
NOMENCLATURE [Front Panel] Reception Indicator Power Switch The left lamp lights when antenna A receives a Press this switch to turn power on. To turn power signal. The right lamp lights when antenna B off, press this switch again. Power Indicator lights receives a signal. when the power is switched on. Level Indicator Power Indicator Lights in proportion to the intensity of input into a Tuner Receptacle wireless microphone. Insert an optional tuner module WTU-870 or WTU- Frequency Label 871. At
Summary of the content on the page No. 4
TUNER MODULE INSTALLATION AND REPLACEMENT CAUTION These servicing instructions are for use by qualified personnel only. To avoid electric shock do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. 1. New Installation (1) Press the stopper of the tuner (3) Open the tuner panel. (4) Insert a tuner module, panel with a screw driver. (2) Pull the tuner panel towards you while pressi
Summary of the content on the page No. 5
OPERATIONS (3) Adjust the volume control of the module of which reception indicator lights. (2) Set the wireless microphone's power switch to ON. The (1) Switch the power on. corresponding module's reception indicator lights. Out The power indicator lights. of two reception indicators for antenna A and B, one corresponding to the antenna receiving the strongest radio signal lights. Note on level indicator The level indicator lights depending on the intensity of input into the wireless microphone
Summary of the content on the page No. 6
INSTALLATION PRECAUTIONS Install the tuner, antennas, and antenna cable away from high frequency noise generating equipment, such as fluorescent lamps and personal computers, whenever possible. Avoid installing receiving antennas in close proximity to metal stuff, such as steel frames and lockers. Install receiving antennas at least 30cm (1 foot) away from the wall. The distance between two antennas must be over 3m (10 feet). If both are installed in the same location, the diversity reception is
Summary of the content on the page No. 7
ADDITIONAL EXPLANATIONS 1. Diversity Reception Conventional single-antenna system receivers have often produced "null spots" where a radio signal is suddenly lost during its reception. The diversity reception method enables stable signal reception all the time. 2. Squelch Circuit In a receiver employing only a noise or carrier squelch, the squelch circuit is actuated and provides the output whenever the receiver receives the same RF carrier as a receiving frequency. This causes even a disturbing
Summary of the content on the page No. 8
SPECIFICATIONS WT-870 Power Requirements 120V AC, 60 Hz ("L" version) 220~240V AC, 50 Hz ("H" version) Power Consumption 10W (when 2 WTU-870's or WTU-871's are mounted) DC Input 12-18V DC, 400mA max. Antenna Input 75 , BNC Power supplied to antenna : 9V DC, 30mA max. Audio Output –60 dBV, 600 , balanced Mixing Output LINE : 0 dBV, 10k , unbalanced MIC : –60 dBV, 600 , unbalanced Operating Temperature –10°C~50°C (14°F~122°F) Dimensions 210X47.5X280mm (8.3"X1.9"X1.0") Weight Approx. 2.3kg (5.07lb.
