Summary of the content on the page No. 1
Installation
Instructions
If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com
36" Stainless Steel
Gas Cooktops
Natural Gas Model:
ZGU375NS
LP Gas Model
ZGU375LS
®
Monogram.
Summary of the content on the page No. 2
Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Owners Manual for future reference. This appliance must be properly grounded and with correct polarity. WARNING See “Power Supply”, page 6. Cet appareil doit être correctement mis à la terre
Summary of the content on the page No. 3
Design Information Stainless Steel G as Cooktop ZGU375NS 36" natural gas cooktop ZGU375LS 36" LP gas cooktop For those who prefer gas heat for cooking, the Monogram built-in gas stainless steel cooktop offers the cooking method of choice. These models are factory set for either natural gas or LP gas operation. Be sure to order the correct model for the installation situation. 13" 36-1/2" Dimensions Max. 20-5/8" and clearances 19-3/4" Deep *2-15/16" Min. at Center From Cooktop to Vertical 30" Co
Summary of the content on the page No. 4
Design Information Stainless Steel G as Cooktop Cooktop and ZVB36 Downdraft Vent Cooktop and ZTD910 Warming Drawer Advance Combination Installation. See page 9. Combination Installation. See page 10. planning These cooktops may be installed with a 36" These cooktops may be installed over a Monogram Downdraft Vent, models ZVB36. Monogram 30" Warming Drawer, models installation See page 9 for cutout and clearances. ZTD910. See page 10 for cutout and clearances. options –The countertop must have a
Summary of the content on the page No. 5
Installation Preparation Stainless Steel G as Cooktop Cut the 11-9/16" Min. Opening Cutout 11-9/16" Min. To Side to Side Wall Wall 35-5/16" 3-3/8" Min. 18-7/8" to Rear Vertical Combustibles 2-3/4" Min. From NOTE: Cutout Front of dimensions have a Countertop tolerance of plus or minus 1/8" CAUTION: Wallcoverings, countertops and cabinets should withstand 200°F heat generated 42" Wide by the cooktop. Cabinet Base Recommended Measure carefully when cutting countertop. • The cooktop chassis occu
Summary of the content on the page No. 6
Installation Preparation Stainless Steel G as Cooktop Gas supply: Power supply These cooktops are shipped from the factory locations set for either natural gas or LP gas. Check to 16" be sure you have the correct cooktop for the 7" type of gas being used. • The pressure regulator must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless of type of gas being used. • The natural gas model is designed to 8" operate at 5" water column pre
Summary of the content on the page No. 7
Installation Stainless Steel G as Cooktop Cooktop • Remove packaging from the cooktop. Step Countertop • Position the cooktop over the opening, making sure that the power cord is dropped 1" Min. 1 into the cabinet. • Lower the cooktop into the cutout, pressing Install NOTE: Countertop gently and evenly to seat. must be a minimum Cooktop of 1" thick at the • Thumbscrew brackets are located on the thumbscrew locations. right and left sides of the cooktop. • Turn thumbscrews to touch the underside
Summary of the content on the page No. 8
Installation Stainless Steel G as Cooktop • Check to be sure the receptacle is properly Step wired by checking for proper polarity and grounding. 3 • Plug in power cord. Connect electrical • Remove tape on burners. Step • Check for proper ignition: • Assemble burner as shown. Check to be sure –Push in one control knob and turn 90° to that burner heads and caps are securely HIGH position. 4 seated. Pin(s) must completely engage holes –The igniter will spark and the burner will to ensure proper as
Summary of the content on the page No. 9
Installation Options Installation With Downdraft Vent Stainless Steel G as Cooktop Cooktop Installation with a 36" Monogram Countertop Requirements: Downdraft Vent, models ZVB36. The countertop must have a deep flat surface The installation of the downdraft vent with to accommodate the cooktop and vent. this cooktop requires careful consideration. Countertops with a rolled front edge and Both the cooktop and the vent must be backsplash will not provide the flat surface installed according to eac
Summary of the content on the page No. 10
Installation Options Installation With Warming Drawer Stainless Steel G as Cooktop Cooktop Installation Over a 30" Monogram –Allow 2" clearance between the cooktop Warming Drawer, models ZTD910. bottom and the top of the cutout, or 7-1/2" These cooktops may be installed over a 30" from the top of the countertop as illustrated. Warming Drawer. Both the cooktop and the warming drawer must be installed according to each specific installation instruction. For Power Supply: accurate planning, review
Summary of the content on the page No. 11
Installation Options Installation With Single Oven Stainless Steel G as Cooktop Cooktop Installation Over a 30" Monogram Power Supply: Single Oven, models ZET1038. The oven requires a separate, properly These cooktops may be installed over the grounded 30 Amp, 3-wire 120/208 or Monogram ZET1038 single oven. Both the 120/240 volt, 60 Hz power supply. The cook- cooktop and the oven must be installed top requires a separate 120V power supply. according to each specific installation instruc- See p
Summary of the content on the page No. 12
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1-800-444-1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-80218-1 Dwg. No. 164D4290P370 03-04 JR 11173-E
