Peerless Industries PE 1120 user manual

Summary of the content on the page No. 1

Installation and Assembly:
Projector Enclosure
Models: PE 1120, PE 1120-W
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 07-11-06 SHEET #: 055-9462-1

Summary of the content on the page No. 2

Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. • This product should only be installed by a qualified professional. • Make sure that the supporting surface will safely support the c

Summary of the content on the page No. 3

Parts List PE 1120 PE 1120-W Description Qty. Part # Part # A projector cage 1 055-1690 055-2690 B top plate 2 055-0695 055-0697 pole clamp 1 055-0694 055-0696 C D .5" dia. X 12" rod 8 580-1163 580-2163 E M5 x 10 mm penta pin screw 4 505-9010 500-2001 F M5 x 1" penta pin driver 1 520-9249 520-9249 5/16-18 nylock nut 1 530-1009 530-1009 G M5 x 10 mm hex screw 3 520-1324 520-2324 H B A E F H G D C ISSUED: 07-11-06 SHEET #: 055-9462-1 3 of 7

Summary of the content on the page No. 4

Suspended Ceiling Application WARNING • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. Note: If flush mount tube has been installed in suspended ceiling mount, remove it before proceeding with this step. From the bottom up, thread extension column (EXT 006, not included) up through retaining collar in adjustable collar 1 mount plate. Align notch in extension column with hole in collar and fasten using M5 x

Summary of the content on the page No. 5

Extension Column Application WARNING • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. Note: Refer to projector mount instruction sheet for attachment of projector mount to extension column. Wrap pole clamp (C) around extension column (not Slide top plates (B) together over pole clamp (C). 1-1 1 included) and secure with nylock nut (G). Hand Slide M5 screws into keyhole slots and tighten as tighten all nyloc

Summary of the content on the page No. 6

Flush Mount Application WARNING • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. Remove M5 penta pin screws from top plates (B). Attach top plates (B) to ceiling using outer holes 1-1 1 indicated in figure 1.1. Note: It is the responsibility of the installer to provide fasteners appropriate for the mounting surface. M5 PENTA PIN SCREW CEILING B B fig 1.1 Note: Refer to projector mount instruction sheet for

Summary of the content on the page No. 7

Slide rods (D) into holes of projector cage (A). Use 2 as many rods as necessary to prevent projector from being removed from projector cage. Note: Position rods where projector lens will not be obstructed. D A Insert pegs on one side of projector cage (A) into Secure projector cage (A) to top plates (B) using 3-1 3 slots of one top plate (B) and slide all the way to four M5 x 10 mm penta pin screws (E). Tighten last notch. Insert pegs on other side of projector screws using penta pin driver (F)