Summary of the content on the page No. 1
2000i
Interactive Whiteboard
Projector Replacement Guide
for Projector Replacement Kits
NEC MT1060R (03-00043) and NEC MT860R (03-00041)
99-00496-00 Rev A0
Summary of the content on the page No. 2
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Opera
Summary of the content on the page No. 3
Contents Replacing the Projector in a 2000i................................................... 1 Aligning the Projected Image........................................................... 6 Customer Support........................................................................... 11 Contacting SMART Technical Support ........................................................11 Other SMART Contacts ...............................................................................11 Product Warranty ....
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Replacing the Projector in a 2000i Use these instructions to install a replacement NEC MT860 or NEC MT1060 projector in your Rear Projection SMART Board 2000i interactive whiteboard. To remove the original projector 1. Shut down the computer, and then press and hold the Projector Standby button on the Control Panel until it blinks rapidly. Wait until you hear the projector’s cooling fan stop (6–7 minutes), and then unplug the 2000i from the power outlet. Projector Standby Button 2. Toggle the pr
Summary of the content on the page No. 6
5. With another person supporting the projector, reach through the view port and remove the three nuts (including the steel and nylon washers) that secure the projector in place and then remove the projector. Use the provided 7/16" nut driver to loosen the nuts. Keep the nuts and washers nearby, as you’ll need them when you install the new projector in step 8. Remove these nuts and washers Be very careful not to lose the spring and nylon shoulder washers on the long CAUTION screw as you remove t
Summary of the content on the page No. 7
6. Set the projector down on a flat surface and remove the projector plate from the projector: Using the provided hex key, loosen and remove the four sets of screws, spacers and washers at the corners of the plate. Cap Screw Lock Washer Flat Washer Aluminum Spacer 7. Transfer the plate to the new projector and attach it using the same screws, spacers and washers that were removed in the previous step. 99-00496-00 REV A0 Projector Replacement Guide for the 2000i 3
Summary of the content on the page No. 8
8. Slide the projector plate back into place by maneuvering the screws through the cabinet slots. With a partner supporting the bottom of the projector, use the provided 7/16" nut driver to secure the projector plate in place using the nuts and washers that you removed in step 5. Place the single nylon washer between the steel washer and the cabinet (see illustration). Also make sure that the spring and shoulder washers remain in place on the long screw. Steel Washer Nylon Washer Spring and Shou
Summary of the content on the page No. 9
9. Connect the video, power and serial cables to the projector, along with any other cables (VCR, external monitor, etc.) that you removed in step 2. Power Cable Video Cable Serial Cable 10. Replace the strap that secures the projector to the projector plate. 11. Plug the power cord back into the power outlet. 12. Toggle the projector power switch to the on position. Main Power Switch 13. Align the projected image as described in the next section. 14. Replace the rear viewport cover. 99-00496-00
Summary of the content on the page No. 10
Aligning the Projected Image If the projected image is blurry or does not fit the screen, complete the four adjustment procedures that follow. For the first three, (roll, side-to-side and image size adjustment), you must watch the image on the back of the screen while making the adjustments. You must also remove the view port cover (attached with hook-and-loop fastener strips) at the rear of the unit to access the adjustment hardware. To adjust image roll 1. Crouch behind the projector and look
Summary of the content on the page No. 11
To adjust the image laterally 1. Crouch behind the projector and look at the projected image through the view port. Image Side-to-Side Adjustment 2. Using the supplied 7/16" nut driver, loosen the two nuts on the left side of the projector plate. 3. Slide the projector plate to the right or left to adjust the image, and then tighten the two nuts. 99-00496-00 REV A0 Projector Replacement Guide for the 2000i 7
Summary of the content on the page No. 12
To change the image size 1. Crouch behind the projector and look at the projected image through the view port. Image Size Adjustment 2. Loosen the four hex screws that secure the projector to the projector plate using the provided 3 mm hex key. NOTE: These screws are located on top of the projector plate, two at the front of the projector and two at the back. 4x 3. Loosen the two hex screws at the front of the projector. To access these screws, reach through the view port, extend your arm to the
Summary of the content on the page No. 13
Screen Removed for Clarity As you maneuver the hex key through the access holes, watch it from the side to see when it engages with the hex screw. Look here to see when the hex key engages with the screw 4. Slide the projector backward or forward to alter the image size. 5. When the image is a good size, tighten all four hex screws that you previously loosened. 99-00496-00 REV A0 Projector Replacement Guide for the 2000i 9
Summary of the content on the page No. 14
To move the image up or down 1. Crouch down in front of the screen. Move Image Up or Down 2. Look underneath the pen tray and locate the Electronics Tray. Locate a plastic cap on the right side of the Electronics Tray. Electronics Tray 3. Remove the plastic cap to reveal an access hole. 4. Use the supplied 7/16" nut driver to loosen and tighten the bolt inside the access hole. This action adjusts the vertical position of the image on the screen. Adjust accordingly. 10 Projector Replacement Guide
Summary of the content on the page No. 15
Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact your local reseller first if you experience problems with any SMART product. SMART’s resellers can readily provide you with quick advice so you can enjoy the benefits of your replacement projector for the Rear Projection SMART Board 2000i interactive whiteboard without delay. Contacting SMART Technical Support All SMART software includes free telephone, fax and e-mail support. There are a number
