Summary of the content on the page No. 1
Installation Guide
LP 425 Series
Ceiling Mount
Installation Guide
LP 425 Series
Installationhandbuch zur
Deckenbefestigung
English. . . . . . . . . . . . .1
Deutsch . . . . . . . . . .13
Summary of the content on the page No. 2
010-0186-00 Copyright © 1998 by In Focus, Inc. Wilsonville, Oregon. All rights reserved. Copyright © 1998 by In Focus, Inc. Wilsonville, Oregon, USA. Alle Rechte vorbehalten.
Summary of the content on the page No. 3
CEILING MOUNT INSTALLATION GUIDE TM The LP 425 LiteMount makes it easy to hang your projector from the ceiling for fixed installa- tion use in meeting, auditorium and training room settings. A unique quick-release feature allows you to take the projector down in seconds to replace the lamp or move the projector to another location. You must determine the suitability of this prod- uct for your intended use and assume all risk WARNING: This installa- and liability in connection therewith. In
Summary of the content on the page No. 4
Placing the Projector Placing the Projector Refer to the LP 425 User’s Guide for image dis- tances and sizes to determine where to install the ceiling mount to meet your projection needs. Contents The LP 425 Ceiling Mount package contains: 1 Installation Guide NOTE: The maximum load the ceiling mount can 2 ceiling mount base box dimensions: 9.6” x 6.0” x 1.4” support is 15 pounds. (24.5 x 15.2 x 3.5 cm) weight: 1.8 lbs (0.8 kg) 3 projector mounting bracket dimensions: 10.2” x 9.9” x 1.5” (25.
Summary of the content on the page No. 5
Install the Ceiling Mount Base Box on the Ceiling Instructions for installing the ceiling mount on the LiteMount False Ceiling Plate and the Lite- WARNING: The ceiling Mount Pipe Tubing Extension are given in this structure must be able to installation guide. If you have not purchased support at least 5 times either of these products, consult a professional the weight of the projector contractor or other facilities professional to ensure a safe installation. and mounting hardware. If
Summary of the content on the page No. 6
Install the Ceiling Mount Base Box on the Ceiling 3 Place the ceiling plate or pipe extension in the ceiling so that the base box hangs down into the room. 4 Route the projector’s cables through your ceiling and out the hole in the ceiling. WARNING: If the dropped ceiling is an air- handling plenum, be sure the cables are plenum- rated, or install the cables within conduit. make sure this surface faces front FIGURE 1 Install the base box to the LiteMount False Ceiling Plate 4
Summary of the content on the page No. 7
false ceiling plate make sure this surface faces front FIGURE 2 Install the base box to the LiteMount Pipe Tubing Extension 5
Summary of the content on the page No. 8
Attach the Mounting Plate to the Projector Attach the Mounting Plate to the Projector 1 Set the projector on a table with the bottom side up. 2 Insert the 2 screws into the 2 quick release sleeves. CAUTION: Use only the hardware that is provided 3 Loosely attach the screws and sleeves to the holes in the projector as shown in Figure 3. with the LP 425 Ceiling Mount. Using different 4 Align the keyholes in the mounting bracket with the screws in the projector. Slide the hardware may damage
Summary of the content on the page No. 9
Hang the Projector on the Ceiling 1 Loosely install the 12 mm knurled knobs, flat washers, and conical spacers to the 2 hinge pins on the base box (Figure 4). spacer washer knurled knob slide projector bracket here between the base box and the spacer FIGURE 4 Attach knurled knobs to the side of the base box 2 Make sure your cables are pulled through the center hole of the base box, then carefully lift the projector and turn it upside down so the mounting plate faces the ceiling (Figure 5).
Summary of the content on the page No. 10
Hang the Projector on the Ceiling FIGURE 5 Install the projector in the ceiling base box 4 Insert the remaining two 12 mm knurled knobs through the rear slots in the mounting bracket and into the threaded holes on the sides of the base box. screen Insert knurled knob through this slot FIGURE 6 Insert the knurled knobs to adjust the angle 8
Summary of the content on the page No. 11
5 Adjust the angle of the projector so that it will project correctly. Refer to your LP 425 User’s Guide for detailed information on projection angles and image sizes. 6 Tighten all the knurled knobs to secure the projector in position. 7 Check all fasteners to make sure they are properly tightened. 8 Connect the power cord and the cables to the projector. (Refer to your LP 425 User’s Guide for information about connecting the cables.) 9
Summary of the content on the page No. 12
Inverting the Image When you need to remove the projector or replace the lamp: 1 Disconnect all cables. 2 Hold the projector from underneath. 3 Remove the knurled knob that holds the pro- jector to the mounting plate. 4 Slide the projector to release it from the quick release bolts. The projector will come off of the mounting plate. The mounting plate will still be attached to the base box. 5 Replace the lamp as described in your LP 425 User’s Guide if needed. 6 Realign the quick release bo
Summary of the content on the page No. 13
Limited Warranty In Focus Inc. warrants that each “ceiling mount” sold hereunder will conform to and function in accordance with the written specifications of In Focus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. The product may contain recycled components that are in new condition. Said warranty shall continue for a period of one (1) year from the date of suc
Summary of the content on the page No. 14
Summary of the content on the page No. 15
INSTALLATIONSANLEITUNG FÜR DIE DECKENBEFESTIGUNG TM Mit dem LiteMount der LP-Serie 425 können Sie Ihren Projektor mühelos zur permanenten Verwendung in Besprechungs-, Vortrags- und Schulungsräumen an der Decke befestigen. Sie müssen die Eignung dieses Produkts für den beabsichtigten Verwendungszweck überprüfen WARNUNG: Diese und übernehmen das gesamte Risiko und die Installation muß gemäß volle Haftung in Zusammenhang mit diesem den jeweils geltenden Bau- Produkt. In Focus empfiehlt, d
Summary of the content on the page No. 16
Plazierung des Projektors Plazierung des Projektors Um die optimale Deckenbefestigungsposition für Ihre Projektionsansprüche zu bestimmen, schlagen Sie bitte die Bildentfernung, die Bild- größe und den Projektionswinkel im LP 425 Benutzerhandbuch nach. Lieferumfang Das Paket mit der Deckenbefestigung für LP- Projektoren der Serie 425 enthält folgendes: 1 Installationsanleitung HINWEIS: Die maximale 2 Deckenbefestigungssockel Belastung des abmessungen: 24,5 x 15,2 x 3,5 cm eigengewicht: 0,8 k
Summary of the content on the page No. 17
Den Deckenbefestigungssockel an der Decke montieren Anweisungen für die Montage der Deckenbefe- stigung auf der LiteMount-Zwischendecken- WARNUNG: Die Dek- platte und der LiteMount-Rohrverlängerung kenstruktur muß minde- sind in der vorliegenden Installationsanleitung stens das fünffache enthalten. Wenn Sie keines dieser beiden Pro- Gewicht des Projektors dukte erworben haben, wenden Sie sich an einen Berufshandwerker, um eine sichere Montage zu und des Befestigungsmate- gewährleisten. r
Summary of the content on the page No. 18
Lieferumfang 3 Montieren Sie die Deckenplatte bzw. die Rohrverlängerung so an der Decke, daß der Sockel in den Raum herabhängt. 4 Führen Sie die Projektorkabel durch die öffnung in der Decke. WARNUNG: Handelt es sich bei der abgehäng- ten Decke um einen Luftverteilerkasten, soll- ten die Kabel in einem Kabelkanal verlegt wer- den. Sockelvorderseite nach vorne zur Leinwand gerichtet ist ABBILDUNG 1 Befestigung des Sockels an der LiteMount-Zwischendeckenplatte 16
Summary of the content on the page No. 19
Sockelvorderseite nach vorne zur Leinwand gerichtet ist ABBILDUNG 2 Befestigung des Sockels an der LiteMount-Rohrverlängerung 17
Summary of the content on the page No. 20
Lieferumfang Die Montageplatte am Projektor befestigen 1 Stellen Sie den Projektor mit der Unterseite nach oben auf einen Tisch. Richten Sie die Löcher in der Montageplatte an den Löchern im Projektor aus. 2 Führen Sie die beiden Schrauben in die bei- den Schnelltrennmuffen ein (Abbildung 3). ACHTUNG: Verwenden Sie nur die mit der 3 Befestigen Sie die Schrauben und Muffen in den Löchern vorne am Projektor, wie in Deckenbefestigung für Abbildung 3 gezeigt. Achten Sie darauf, daß Projekt
