Summary of the content on the page No. 1
GE Fanuc Automation
Programmable Control Products
CIMPLICITY® Display Station
Touch Display:
IC752CTD400/450
GFK-1425B March 1998
Summary of the content on the page No. 2
GFL-002 Warnings, Cautions, and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. No
Summary of the content on the page No. 3
Preface Content of This Manual This manual describes the features and operation of the following CIMPLICITY Display Station Touch Display products: Catalog Number IC752CTD400 IC752CTD450 Related Publications ® ® GFK-1189 CIMPLICITY HMI for Windows NT™ and Windows 95 Important Product Information ® GFK-1180 CIMPLICITY HMI for Windows NT™/CIMPLICITY HMI for ® Windows 95/CIMPLICITY Server for Windows NT™ Base System User Manual ® GFK-1181 CIMPLICITY HMI for Windows NT™/CIMPLICITY HMI for ® Window
Summary of the content on the page No. 4
Contents Product Features..................................................................................................... 2 Display and Touch Screen ................................................................................................... 3 Floppy Disk Drive Unit ....................................................................................................... 3 Hardware Installation............................................................................................
Summary of the content on the page No. 5
Contents System Configuration Verification ............................................................................. 26 Troubleshooting.................................................................................................................27 Powerup....................................................................................................................... 27 Display..........................................................................................................
Summary of the content on the page No. 6
Contents Figure 1. Touch Display Unit Dimensions...................................................................................................... 5 Figure 2. Panel Cutout Dimensions................................................................................................................. 6 Figure 3. Mounting the Touch Display Unit ................................................................................................... 6 Figure 4. Card Clamp ...........................
Summary of the content on the page No. 7
Contents Table 1. Touch Display Features..................................................................................................................... 2 Table 2. Touch Screen (Custom COM) I/O address ....................................................................................... 9 Table 3. Touch Screen (Custom COM) IRQ................................................................................................... 9 Table 4. Connector Listing...............................
Summary of the content on the page No. 8
CIMPLICITY® DISPLAY STATION GFK-1425B Touch Display Products March 1998 IC752CTD400, IC752CTD450 Welcome to GE Fanuc’s CIMPLICITY Display Station products. These products provide an integrated hardware and software platform for running CIMPLICITY HMI applications. The Touch Display incorporates CIMPLICITY HMI software for Windows and either Microsoft Windows® 95 or Microsoft Windows NT® software (depending on model). The 10.4” active matrix, thin film transistor (TFT) color displays provide a
Summary of the content on the page No. 9
Product Features When you purchase a CIMPLICITY Touch Display system, you receive: • CIMPLICITY Display Station industrial computer with CIMPLICITY HMI and operating system software installed. • Power cord • Floppy disk drive (3.5-inch) • Installation hardware • CIMPLICITY Display Station Data Sheet which describes specifics of the hardware and software for your particular system • CIMPLICITY Display Station system documentation • CIMPLICITY software licenses and license agreements • Ethernet
Summary of the content on the page No. 10
Display and Touch Screen The Touch Display features a color liquid crystal display (LCD) with a touch screen surround. The touch-screen surround, which is an integral part of the front panel on all Touch Display Flat Screen models, makes operation of a configured system more intuitive by allowing the operator to interface with the system by simply touching the screen. The performance of the Touch Display unit is not affected by bright sunlight. The system can also differentiate between a true
Summary of the content on the page No. 11
Hardware Installation This section describes procedures for mounting the Touch Display unit, and installing ISA- compatible cards and the floppy disk drive unit. A single cut-out is required in the mounting panel. No extra holes are required. Instead, ten spring- loaded retaining clips are supplied to secure the unit from behind the panel. Note The Touch Display unit with processor card weighs 11kg (25lbs) approx. The 3.5-inch disk drive adds 1kg (2.2lbs) to the weight when installed. Mounting
Summary of the content on the page No. 12
Figure 1. Touch Display Unit Dimensions GFK-1425B Touch Display Products: IC752CTD400/450 5
Summary of the content on the page No. 13
Mounting Procedure 1. Cut out the panel to the dimensions shown. The cut-out dimensions of 367 x 255mm (14.45 x 10.04 inches) allow a 1.5mm (0.06 inch) clearance on each edge of the Touch Display unit. Figure 2. Panel Cutout Dimensions 2. Position the Touch Display unit in the cut-out and fit the ten spring-loaded retaining clips into the slots. All ten clips must be installed to achieve a good seal. Figure 3. Mounting the Touch Display Unit 3. Screw in the tightening screw on each clip so t
Summary of the content on the page No. 14
Installing ISA-Compatible Cards The Touch Display rear panel must be removed in order to gain access to the ISA bus cards. There are six screws securing the rear panel. When these are removed, the rear panel can be lifted away from the main unit. Warning Switch off the unit and disconnect the main power input before removing the rear panel. Blanking Plates Blanking plates are installed on each unused card position. Remove blanking plates as necessary to install new cards. Empty slots must alwa
Summary of the content on the page No. 15
I/O Address and IRQ Allocation Caution For most applications an IRQ cannot be shared by more than one resource. If more than one resource is set to the same interrupt, the application may not respond properly and could cause your machine to lock up. The I/O address and IRQ number of cards being installed must not conflict with those of cards already installed. Refer to "Interrupt and I/O Assignments" on page 25 for a list of factory-set IRQs. We strongly recommend that you use only the interru
Summary of the content on the page No. 16
Figure 5. Jumper Locations Table 2. Touch Screen (Custom COM) I/O address LK2 LK3 Address OUT OUT Disabled IN OUT 2E8 hexadecimal OUT IN 310 hexadecimal (factory default) IN IN 3E8 Table 3. Touch Screen (Custom COM) IRQ One jumper determines the IRQ number, depending on its position: LK6 IRQ3 LK7 IRQ4 LK8 IRQ5 (factory default) LK9 IRQ6 LK10 IRQ7 LK11 IRQ9 GFK-1425B Touch Display Products: IC752CTD400/450 9
Summary of the content on the page No. 17
Installing the Floppy Disk Drive The floppy disk drive is designed for mounting on the rear panel of the Touch Display unit. Two locating slots in the rear panel accept the two metal brackets on the disk drive housing. A thumbscrew fastens the drive assembly to the rear panel. A ribbon cable, terminated with a D-type connector, extends from the disk drive to the floppy disk connector at the side of the unit. Figure 6. Floppy Disk Drive Mounting Caution The Touch Display unit must be powered o
Summary of the content on the page No. 18
Changing the Air Filter The filter element should be changed every three months, or sooner in dusty environments. If the air filter is not changed at suitable intervals, or a non-approved filter element is installed, the unit may overheat. Filter Type: 6.35mm (0.25 inch) thick polyester/polyurethane open cell foam (45 ppi) To change the air filter element: The filter element is held directly behind the filter plate in the side of the Touch Display unit. Figure 7. Filter Element Location Cauti
Summary of the content on the page No. 19
Connection All connections are made on the side panel of the Touch Display unit. The connector layout is shown in Figure 8. Figure 8. Touch Display Connectors Table 4. Connector Listing Card Slot (from top) Type Function none 3-prong AC power receptacle Power input 1 25-pin, female, D-type Parallel communications 2 37-pin, female, D-type Floppy disk drive connection 3 15-pin, female high density D-type VGA CRT output 4A 6-pin, mini DIN Keyboard connection 4B 9-pin, male, D-type Serial commu
Summary of the content on the page No. 20
AC Power Input The power input connector is a standard CEE22 type. A power cable is supplied with the Touch Display unit. The power supply is auto-ranging, therefore no configuration is needed to change the unit between 110 volt AC and 240 volt AC operation. Check that the fuse is of the correct rating for the supply voltage. The panel mounted power input connector houses a 5 x 20mm fuse in a compartment adjacent to the input socket. The fuse-holder can be accessed only when the power lead is
