Summary of the content on the page No. 1
INTELLIGENT DISPLAYS
BARCOREALITY 6500
R9001960
R9001969
OWNER’S MANUAL
30012001 R5976182/01
Summary of the content on the page No. 2
Barco nv Media Noordlaan 5, 8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: media@barco.com Visit us at the web: www.barco.com Printed in Belgium
Summary of the content on the page No. 3
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO. Changes Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied war- rantiesormerchantabilityandfitnessfora particularpurpose. Barcomaymake improvementsand/orchangestotheproduct(s)and/orthe program(
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Table of contents TABLE OF CONTENTS 1. PackagingandDimensions........................................................................................5 1.1Boxcontent.............................................................................................................................. 5 1.2ProjectorPackaging..................................................................................................................... 5 1.3 Lens Packaging................................................
Summary of the content on the page No. 6
Table of contents 7.2.5.1. Startup ...................................................................................................................45 7.2.5.2. Changing the settings....................................................................................................45 7.2.5.3. Correctvalue .............................................................................................................45 7.2.6 Rename....................................................................
Summary of the content on the page No. 7
Table of contents 9.6.3CommonAddress................................................................................................................80 9.7 Change Baudrate PC ..................................................................................................................81 9.8ResetLampRuntime...................................................................................................................81 9.9 Lamp Run time History...............................................
Summary of the content on the page No. 8
Table of contents 4 R5976182 BARCOREALITY 6500 30012001
Summary of the content on the page No. 9
1. Packaging and Dimensions 1. PACKAGING AND DIMENSIONS This chapter handles about the way the projector is packed and gives an overview of the dimensions. Box content Projector Packaging Lens Packaging Dimensions 1.1 Box content CEE7 European power plug to connect the power cord to the wall outlet. ANSI 73.11 American power plug to connect the power cord to the wall outlet. Content 1 projector BARCOREALITY SIM6(weight ± 17 kg or 37.4 lbs) 1 remote control unit RCU + 2 batteries. 2
Summary of the content on the page No. 10
1. Packaging and Dimensions 1.3 Lens Packaging Way of Packaging Lenses are supplied as an individual item. They are packed in a carton box. 1.4 Dimensions Dimensions overview Dimensions are given in mm (1 inch = 25.4 mm) Image 1-2 Front view dimensions projector 6 R5976182 BARCOREALITY 6500 30012001
Summary of the content on the page No. 11
1. Packaging and Dimensions Image 1-3 Side view dimensions projector Image 1-4 Top view dimensions projector R5976182 BARCOREALITY 6500 30012001 7
Summary of the content on the page No. 12
1. Packaging and Dimensions 8 R5976182 BARCOREALITY 6500 30012001
Summary of the content on the page No. 13
2. Installation Guidelines 2. INSTALLATION GUIDELINES Overview Installation guidelines Configuration Lenses Batteries Before installing the projector, read first the safety instructions. 2.1 Installation guidelines Ambient Temperature Conditions. Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 40 C or 104 F Min. ambient temperature :
Summary of the content on the page No. 14
2. Installation Guidelines and lightestparts ofthe image. With biggerscreens, the ‘wash out’becomesmore important. As a generalrule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimal. Which screen type ? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection appli
Summary of the content on the page No. 15
2. Installation Guidelines Image 2-1 B Distance between ceiling and top of the screen or between floor and bottom of the screen. A Correction value, distance between bottom side of projector (without feet) and middle of the lens. Value to be subtracted from B to obtain the correct installation position. (A value is a constant value for all screen widths and type of lenses, A = 124.1 mm or 4.89 inch) CD Total distance between projector and ceiling or projector and floor. SWScreen width SH Screen
Summary of the content on the page No. 16
2. Installation Guidelines 2.3.1 Lenses Available lenses The following lenses are available, or will become available (contact a BARCO service center) as an option : Lenses Standard version QFD(1.27:1) R9840400 QFD(2.5:1) R9840290 QFD(1.4-2.1:1) R9840380 QFD(2.1-3.0:1) R9840390 QFD(3.5-4.5:1) R9840060 QFD(4.5-6.0:1) R9840100 QFD(7:1) R9840410 2.3.2 Lens selection How to select ? 1. Determine the required screen width. 2. Determine the approximate position of the projector in the projection room
Summary of the content on the page No. 17
2. Installation Guidelines 2.3.4 Lens installation How to install ? Follow the next procedure : 1. Open the lens cover of the projector by pivoting it up and take it off. (image 2-2) 2. Pull the lens locks levers backwards to open the lens locks. (image 2-3) 3. Put the lens on the lens holder. (image 2-4) 4. Push the lens locks back in position and lock the levers. 5. Plug the wires of the motor unit into the connector (image 2-5) 6. Re-install the lens cover. Image 2-3 Image 2-2 Image 2-5 Image
Summary of the content on the page No. 18
2. Installation Guidelines Necessary tools TM Toraysee cloth (delivered together with the lens kit). Order number : R379058. Howtocleanthelens? Proceed as follow : TM 1. Always wipe lenses with a CLEAN Toraysee cloth. 2. Always wipe lenses in a single direction. Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating. 3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth. 4. If smears oc
Summary of the content on the page No. 19
2. Installation Guidelines Image 2-6 Image 2-7 Note, only important if more than one projector is installed in the room. The common address can be zero (0) or one (1). The standard RCU are setup for common address zero. To change the common address of the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see chapter ’Getting Started’. Projector address has to be reprogrammed every time the battery is changed, the RCU will always switch to the
Summary of the content on the page No. 20
2. Installation Guidelines 16 R5976182 BARCOREALITY 6500 30012001
