Summary of the content on the page No. 1
S PEC F ILE
The PT-DZ6710L is not equipped with a lens.
Product Number : PT-DZ6710/DZ6710L
™
Product Name : DLP Projectors
As of February 2009. Specifications subject to change without notice. < 1 >
Summary of the content on the page No. 2
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Specifications Main Unit Power supply: North America: 120 V AC, 50/60 Hz Europe: 220–240 V AC, 50/60 Hz 1 Power consumption: North America: 820 W (880 VA) (Standby mode eco* : 0.2 W, Standby mode normal: 8 W. Both with fan stopped.) 1 Europe: 800 W (960 VA) (Standby mode eco* : 0.3 W, Standby mode normal: 9 W. Both with fan stopped.) DLP™chip: Panel size: 0.67˝ diagonal (16:10 aspect ratio) Display method: DLP™ chip x 1, DLP™ system Pixels: 2,304,
Summary of the content on the page No. 3
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L RGB 1 IN: BNC x 5 R, G, B: R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD/VD, SYNC: High impedance, TTL (positive/negative), 75 ohms Y, PB, PR: Y: 1.0 Vp-p (including sync signal), PB/PR: 0.7 Vp-p, 75 ohms NOTE: HD/SYNC, and VD terminals do not accept tri-leve sync signals. D-sub HD 15-pin x 1 RGB 2 IN: R: 0.7 Vp-p, 75 ohms, R, G, B: G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75
Summary of the content on the page No. 4
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-DZ6710. 416 (16-3/8˝) 498 (19-19/32˝) Terminals 123 4 5 1 Video input 7 Remote 1 input 2 S-Video input 8 Remote 1 output R/PR G/Y B/PB SYNC/HD VD 3 RGB 1 input 9 Remote 2 input LAN VIDEO IN S-VIDEO IN RGB1 IN RGB2 IN DVI-D I N IN OUT 4 RGB 2 Input 10 Serial input IN SERIAL OUT SDI REMOTE 1 REMOTE 2 5 DVI-D input 11 Serial output 6 LAN connec
Summary of the content on the page No. 5
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Standard setting-up position (when installed using the ET-PKD56H) *1 When the lens protrudes to the maxi- mum. 185 mm (7-9/32˝) with the supplied lens 212 mm (8-11/32˝) with the ET-DLE150 213 mm (8-3/8˝) with the ET-DLE250 219 mm (8-5/8˝) with the ET-DLE350 Upper edge of projected image 263 mm (10-11/32˝) with the ET-DLE450 195 mm (7-11/16˝) with the ET-DLE055 L *2 Adjustable in 40 mm (1-9/16˝) steps. 1 * 256 Projected image (10-1/32˝) L Lower edge
Summary of the content on the page No. 6
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Projection distance for 16:10 aspect ratio screen Unit: millimeters Screen Distance to screen (L) Height from the edge of screen to size Zoom Fixed-focus center of lens (H) (inch, diagonal) Zoom Fixed- ET-DLE150 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 ET-DLE055 focus lenses Zoom lens Zoom lens Zoom lens Zoom lens Fixed-focus lens* lens min. max. min. max. min. max. min. max. min. max. 50 1,376 2,013 1,901 2,571 2,418 3,865 3,802 5,815 5,659 9,12
Summary of the content on the page No. 7
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Projection distance for 16:9 aspect ratio screen Unit: millimeters Screen Distance to screen (L) Height from the edge of screen to size Zoom Fixed-focus center of lens (H) (inch, diagonal) Zoom Fixed- ET-DLE150 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 ET-DLE055 focus lenses Zoom lens Zoom lens Zoom lens Zoom lens Fixed-focus lens* lens min. max. min. max. min. max. min. max. min. max. 50 1,416 2,070 1,956 2,645 2,487 3,975 3,911 5,980 5,824 9,385
Summary of the content on the page No. 8
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Projection distance for 4:3 aspect ratio screen Unit: millimeters Screen Distance to screen (L) Height from the edge of screen to size Zoom Fixed-focus center of lens (H) (inch, diagonal) Zoom Fixed- ET-DLE150 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 ET-DLE055 focus lenses Zoom lens Zoom lens Zoom lens Zoom lens Fixed-focus lens* lens min. max. min. max. min. max. min. max. min. max. 50 1,565 2,286 2,162 2,920 2,747 4,386 4,322 6,600 6,446 10,368
Summary of the content on the page No. 9
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 ET-DLE150 minimum L (mm) = (diagonal screen size in inches) x 28.6 – 54.0 maximum L (mm) = (diagonal screen size in inches) x 41.3 – 49.8 Supplied lens minimum L (mm) = (diagonal screen size in inches) x 39.5 – 74.5 maximum L (mm) = (diagonal screen size in inches) x 52.9 – 73.4 ET-DLE250
Summary of the content on the page No. 10
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • Floor mount • Ceiling mount H (Width of projected image) 0.1H 0.1H Standard postition of projected image Standard postition of projected image 0.1H 0.1H H (Width of projected image) Installable angle Install the projector at an angle within the range shown below. • Vertical direction • Horizontal direction The projector may be installed at a
Summary of the content on the page No. 11
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L List of compatible signals This projector supports RGB signals with horizontal frequencies of 15 to 91 kHz, vertical frequencies of 50 to 85 Hz and up to 162 MHz dot clock. NOTE: The native resolution of this projector is 1,920 x 1,200 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution. Display m
Summary of the content on the page No. 12
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names No. Signal name Description No. Signal name Description 1 – NC 6 – NC 2 TXD Send data 7 CTS Connected internally 3 RXD Receive data 8 RTS Connected internally 4 – Connected
Summary of the content on the page No. 13
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Projector PC (DTE) Cable specifications NC NC 1 1 2 2 3 3 NC NC 4 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC 9 Control commands Command : Parameter Function Callback PON POWER (STANDBY) Standby power on PON POF Standby power off POF IIS:SDI INPUT SELECT SDI IIS:SDI IIS:DVI DVI IIS:DVI IIS:RG1 RGB 1 IIS:RG1 IIS:RG2 RGB 2 IIS:RG2 IIS:VID Video IIS:VID IIS:SVD S-VideoAUX IIS:SVD LPM:0 Dual (two lamps) LPM:0 LPM:1 LAMP SELECT Lamp 1 LPM:1 LPM:2 Lamp 2 LPM:2 LPM:3
Summary of the content on the page No. 14
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Status asking commands Command:Parameter Function Callback Description QPW Main power status 000 Standby (Off) 001 On QSH Shutter function status 0 Off 1 On QFZ Freeze function status 0 Off 1 On QIN Input signal status SDI SDI DVI DVI RG1 RGB 1 RG2 RGB 2 VID Video QOS On-screen display status SVD S-Video 0 Off QST Projector run time 1 On Q$L:1 p1p2p3p4p5 Lamp 1 run time 00000h–99999h Q$L:2 Lamp 2 run time p1p2p3p4 0000h–9999h QSL p1p2p3p4 Lamp opera
Summary of the content on the page No. 15
S PEC F ILE ™ DLP Projectors PT-DZ6710/DZ6710L Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another. If two units must be stacked for back- up use in or
