Summary of the content on the page No. 1
S PEC F ILE
The PT-DW6300LS and PT-DW6300LK are not equipped with a lens.
Product Number : PT-DW6300S/DW6300K
PT-DW6300LS/DW6300LK
™
Product Name : DLP Projectors
As of February 2009. Specifications subject to change without notice. < 1 >
Summary of the content on the page No. 2
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Specifications Main Unit Power supply: North America: 120 V AC, 50/60 Hz Europe: 220–240 V AC, 50/60 Hz 1 Power consumption: North America: 780 W (780 VA) (Standby mode eco* : 0.2 W, Standby mode normal: 8 W. Both with fan stopped.) 1 Europe: 750 W (840 VA) (Standby mode eco* : 0.3 W, Standby mode normal: 9 W. Both with fan stopped.) DLP™chip: Panel size: 0.65˝ diagonal (16:10 aspect ratio) Display method: DLP™ chip x 1, DLP™ sy
Summary of the content on the page No. 3
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK RGB 2 IN: D-sub HD 15-pin x 1 R, G, B: R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD/VD, SYNC: High impedance, TTL (positive/negative), 75 ohms NOTE: HD/SYNC, and VD terminals do not accept tri-level sync signals. Y: 1.0 Vp-p (including sync signal), PB/PR: 0.7 Vp-p, 75 ohms Y, PB, PR: BNC x 1, 1.0 Vp-p, 75 ohms VIDEO IN: Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms S-V
Summary of the content on the page No. 4
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-DW6300S/DW6300K. 416 (16-3/8˝) 498 (19-19/32˝) Terminals 123 4 5 1 Video input 7 Remote 1 input 2 S-Video input 8 Remote 1 output R/PR G/Y B/PB SYNC/HD VD 3 RGB 1 input 9 Remote 2 input LAN VIDEO IN S-VIDEO IN RGB1 IN RGB2 IN DVI-D I N 4 RGB 2 Input 10 Serial input IN OUT 5 DVI-D input 11 Serial output REMOTE 1 REMOTE 2 IN
Summary of the content on the page No. 5
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Standard setting-up position (when installed using the ET-PKD56H) *1 When the lens protrudes to the maxi- mum. 185 mm (7-9/32˝) with the supplied lens 212 mm (8-11/32˝) with the ET-DLE150 213 mm (8-3/8˝) with the ET-DLE250 219 mm (8-5/8˝) with the ET-DLE350 Upper edge of projected image 263 mm (10-11/32˝) with the ET-DLE450 195 mm (7-11/16˝) with the ET-DLE055 L *2 Adjustable in 40 mm (1-9/16˝) steps. 1 * 256 Projected image (10-1
Summary of the content on the page No. 6
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Projection distance for 16:10 aspect ratio screen Unit: millimeters Screen Distance to screen (L) Height from the edge of screen to size Zoom Fixed-focus center of lens (H) (inch, diagonal) Zoom Fixed- ET-DLE150 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 ET-DLE055 focus lenses Zoom lens Zoom lens Zoom lens Zoom lens Fixed-focus lens* lens min. max. min. max. min. max. min. max. min. max. 50 1,447 2,116 1,922 2,557 2,542 4,063 3,9
Summary of the content on the page No. 7
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Projection distance for 16:9 aspect ratio screen Unit: millimeters Screen Distance to screen (L) Height from the edge of screen to size Zoom Fixed-focus center of lens (H) (inch, diagonal) Zoom Fixed- ET-DLE150 Supplied lens ET-DLE250 ET-DLE350 ET-DLE450 ET-DLE055 focus lenses Zoom lens Zoom lens Zoom lens Zoom lens Fixed-focus lens* lens min. max. min. max. min. max. min. max. min. max. 50 1,489 2,176 1,977 2,630 2,615 4,178 4,11
Summary of the content on the page No. 8
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 ET-DLE150 minimum L (mm) = (diagonal screen size in inches) x 30.0 - 54.0 maximum L (mm) = (diagonal screen size in inches) x 43.3 - 49.8 Supplied lens minimum L (mm) = (diagonal screen size in inches) x 39.7 - 65.0 maximum L (mm) = (diagonal screen size in inches) x 52.
Summary of the content on the page No. 9
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • Floor mount • Ceiling mount H (Width of projected image) 0.1H 0.1H Standard postition of projected image Standard postition of projected image 0.1H 0.1H H (Width of projected image) Installable angle Install the projector at an angle within the range shown below. • Vertical direction • Horizontal direction The projector ma
Summary of the content on the page No. 10
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK List of compatible signals This projector supports RGB signals with horizontal frequencies of 15 to 91 kHz, vertical frequencies of 50 to 85 Hz and up to 150 MHz dot clock. NOTE: The native resolution of this projector is 1,024 x 800 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native reso
Summary of the content on the page No. 11
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names No. Signal name Description No. Signal name Description 1 – NC 6 – NC 2 TXD Send data 7 CTS Connected internally 3 RXD Receive data 8 RTS Connected inter
Summary of the content on the page No. 12
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Projector PC (DTE) Cable specifications NC NC 1 1 2 2 3 3 NC NC 4 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC 9 Control commands Command : Parameter Function Callback PON POWER (STANDBY) Standby power on PON POF Standby power off POF IIS:DVI INPUT SELECT DVI IIS:DVI IIS:RG1 RGB 1 IIS:RG1 IIS:RG2 RGB 2 IIS:RG2 IIS:VID Video IIS:VID IIS:SVD S-VideoAUX IIS:SVD LPM:0 Dual (two lamps) LPM:0 LPM:1 LAMP SELECT Lamp 1 LPM:1 LPM:2 Lamp 2 LPM:2 LPM:3 S
Summary of the content on the page No. 13
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Status asking commands Command:Parameter Function Callback Description QPW Main power status 000 Standby (Off) 001 On QSH Shutter function status 0 Off 1 On QFZ Freeze function status 0 Off 1 On QIN Input signal status DVI DVI RG1 RGB 1 RG2 RGB 2 VID Video SVD S-Video QOS On-screen display status 0 Off 1 On QST Projector run time p1p2p3p4p5 00000h–99999h Q$L:1 p1p2p3p4 Lamp 1 run time 0000h–9999h Q$L:2 Lamp 2 run time p1p2p3p4 000
Summary of the content on the page No. 14
S PEC F ILE ™ DLP Projectors PT-DW6300S/DW6300K/DW6300LS/DW6300LK Notes on Projector Placement and Operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another. If two units must be stacked for
