Summary of the content on the page No. 1
MultiSync Hivid 6500 Projector
Large Screen MultiSync Projection System
User’s Manual
Model number: XL-6500/XL-6500G
Summary of the content on the page No. 2
Precautions CAUTION: To turn off main power, be sure to remove the Please read this manual carefully before using your NEC plug from power outlet. The power outlet socket should be MultiSync Hivid 6500 Projector and keep the manual handy installed as near to the equipment as possible, and should for future reference. be easily accessible. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) according to ISO 3744 or ISO 7779. WARNING AVERTISSEMENT TO PREVEN
Summary of the content on the page No. 3
INTRODUCTION Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation 1. Place the projector on a flat, level surface and in a dry area free from dust and moisture. 2. Do not place the projector in direct sunlight, near heaters or heat radiating appliances. 3. Exposure to direct sunlight, smoke or steam could harm internal components. 4. Handle your projector carefull
Summary of the content on the page No. 4
INTRODUCTION Recommandations importantes Ces instructions de sécurité ont pour but d'assurer une longue vie à votre projecteur et d'éviter un incendie ou une décharge électrique. Prière de les lire avec attention et de tenir compte de tous les avertissements. Installation 1. Placer le projecteur sur une surface plate et de niveau, et dans un endroit sec et à l'abri des poussières et de l'humidité. 2. Ne pas exposer le projecteur aux rayons directs du soleil, ni le placer près d'un chauffage ou d
Summary of the content on the page No. 5
VISUAL SYSTEMS DIVISION 1234567 1 23456 7 1 23456 7 1 23456 7 1 23456 7 1 23456 7 1234567 LIMITED WARRANTY . NEC Technologies, Inc.(hereafter NECTECH)warrants this prod- HOW YOU CAN GET WARRANTY SERVICE uct to be free from defects in material and workmanship under the 1. To obtain service on your product, consult the dealer from following terms. whom you purchased the product, or ship it prepaid to any authorized NECTECH service center. HOW LONG IS THE WARRANTY 2. Whenever warranty service is re
Summary of the content on the page No. 6
123456 1 2345 6 1 2345 6 1 2345 6 1 2345 6 123456 TABLE OF CONTENTS. INTRODUCTION Introduction To The MultiSync Hivid 6500 Projector.............. 7 How Do You Get Started?....................................................... 7 What’s In The Box? ................................................................ 7 1.PART NAMES AND FUNCTIONS Input Panel Features ............................................................... 8 Ajusting and Setting (Adjust Menu) ..................................
Summary of the content on the page No. 7
123456 1 2345 6 1 2345 6 1 2345 6 1 2345 6 123456 INTRODUCTION. This section introduces you to your new MultiSync Hivid 6500 Projector, provides a list of materials that comes with your projector and describes the features and controls. Congratulations On Your Purchase Of The MultiSync Hivid 6500 Projector TM The MultiSync Hivid 6500 is one of the very best projectors available today. Digital Light Processing TM (DLP ) by Texas Instruments enables you to project high bright precise images up to
Summary of the content on the page No. 8
1234567 1 23456 7 1 23456 7 1 23456 7 1 23456 7 1234567 1.PART NAMES AND FUNCTIONS. This compartment accommodates the remote control. The remote control serves as the key panel on the projector when it is plugged and fit in this compartment. POWER ON/STANDBY Indicator lights in green when the projector is turned on and lights in red when the projector is in standby. 11 111 POWER XL-6500G ON/STANDBY Indicator OFF BREAKER ON @@ @@ @@@@ @@ @@@@ @@ @@@@@@
Summary of the content on the page No. 9
1.PART NAMES AND FUNCTIONS 6666677777 88 888 55 555 99 POWER STANDBY RCREADY LAMP 999 POWER ON/OFF OFF ON 00 000 INDICATOR AA AAA IN REMOTE2 OUT CC CCC BB BBB REMOTE1 IN OPTION OUT DD DDD EEEEE @@ @@ @@ @@ @@ @@@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@@@ @@@@ @@ @@ @@@@ @@@@ @@@@@@ @@ @@ @@ @@ @@ @@ @@
Summary of the content on the page No. 10
1.PART NAMES AND FUNCTIONS OPTIONAL Boards VIDEO INPUT Board [XG VIDIN (A)] Front view 12 3 4 5 LR LR VIDEO S-VIDEO VIDEO INPUT VIDEO S-VIDEO AUDIO INPUT 1 Active Indicator (green LED) ...... Lights up when this board is selected. 2 VIDEO INPUT Terminal ............... Connects composite video output signals. 3 S-VIDEO INPUT Terminal ........... Connects S-video output signals. 4 VIDEO INPUT Terminal ............... Connect to the audio outputs of the external equipment such as a VCR. (Not ava
Summary of the content on the page No. 11
9 8 7 6 RGB 1.PART NAMES AND FUNCTIONS The combination of the rotary switch and the jumper pins allows the projector to accept VIDEO signals. Note that this board cannot accept RGB signals when board is set to VIDEO input. Rotary switch (S1001) Jumper (S1002, S1003, S1004) Setting of Rotary switch No. Mark Input 0 VIDEO VIDEO input 5 1 OPTION Option *1 *2 3 RGB RGB input 2, 4-9 Not used *1 ) No 1 is for future system expansion. *2) No 3 is factory preset. Table for Setting Rotary S
Summary of the content on the page No. 12
1.PART NAMES AND FUNCTIONS Remote control unit 1 Remote Jack 1 Insert the supplied remote cable here. 2 POWER Buttons (ON/OFF) Press the ON button to turn the projector on when the projector is in the standby condition (STANDBY and RC POWER INPUT READY indicators lit). Press the OFF button to return the ON OFF 1 ABC 2 DEF 3 GHI projector to the standby condition. 2 TEST 4 JKL 5 MNO 6 PQR 3 TEST Button 3 H Press to display the TEST PATTERN menu from which 4 OPERATE ADJUST 7 STU 8 VWX 9 YZ/ you ca
Summary of the content on the page No. 13
1.PART NAMES AND FUNCTIONS B HELP Button O R, G, and B Buttons Press to display the explanation of the current selected The R and B buttons are used for Uniformity only. function and available functions. P CURSOR Buttons C SIG LEVEL Button Used for increasing and decreasing control levels, cursor Press to display the SIGNAL LEVEL menu. You can set movement and convergence adjustments. the level for an RGB or component signal. Q DELETE Button D GAMMA Button Used to delete characters or numbers yo
Summary of the content on the page No. 14
1.PART NAMES AND FUNCTIONS Remote Control Battery Installation 1. Press firmly and slide the battery cover off. 2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries’ polarity (+/-) aligned correctly. 3. Slip the cover back over the batteries until it snaps into place. NOTE: The remote control is powered by two alkaline 1.5V AA batteries. Remote Control Precautions • When using the remote wirelessly, you should be within 23 ft.(7 m) of the projector and at a
Summary of the content on the page No. 15
OPEN Remote Control Unit 1.PART NAMES AND FUNCTIONS When using the remote control as the key panel on the projector: The following steps are necessary only when the projector is installed on the ceiling. When you use the projector in floor projection, you do not need to fasten the remote with the metal fitting. Simply open the lid and put the remote in the compartment. @@ @@ @@ @@@@ @@@@ @@@@@@ @@ @@@@@@ @@
Summary of the content on the page No. 16
1234567 1 23456 7 1 23456 7 1 23456 7 1 23456 7 1234567 2. INSTALLATION This section describes how to set up your MultiSync Hivid 6500 projector and how to connect video and audio sources. Setting Up Your MultiSync Hivid 6500 Projector To set up and use your MultiSync Hivid 6500 Projector, you must first do: 1. Determine the screen size and the optional lens to be used. NOTE: Consult your dealer for lens order and installation. 2. Set up a screen or select a non-glossy white wall onto which
Summary of the content on the page No. 17
2.INSTALLATION Screen Size and Projection Distance Projector Screen 1. Place your projector on a flat level surface at the optimal distance from the screen or wall so you realize the size image you want. (Avoid having bright room lighting or sun light directly on the screen or wall where you’ll be projecting the image.) 2. Connect the power cable, remove the lens cap and Screen center Lens center turn the projector on. (If no input signal is avail- Projector able, the projector will display a bl
Summary of the content on the page No. 18
2.INSTALLATION n Projection model : XL-3500/3500G Model No. XL-L1.27 XL-L3 XL-L5 XL-L7 XL-L1.5Z XL-L3Z Lens Magnification Zoom3.0-7.0 1.27:1 3.0:1 5.0:1 7.0:1 Zoom1.5-3.0 2.58m 6.10m 10.16m 3.05-6.10m 14.22m 6.10-14.22m Screen size 100" 102in 240in 400in 120-240in 560in 240-600in (Diagonal) 5.16m 12.19m 20.32m 28.45m 6.10-12.19m 12.19-28.45m 200" 203in 480in 800in 1120in 240-480in 480-1120in 7.74m 18.29m 9.14-18.29m 18.29-42.67m 30.48m 42.67m 300" 305in 720in 360-720in 720-1680in 1200in 1680in 1
Summary of the content on the page No. 19
2.INSTALLATION Reflecting The Image Using a mirror to reflect your projector’s image enables you to enjoy a much larger image. Contact your NEC dealer if you need a mirror. If you’re using a mirror and your image is inverted, use the ADJUST-SETTING Menu to access to correct the orientation. (See page 59.) Rear Screen Projection You can use your MultiSync Hivid 6500 to project an image from the rear onto a transparent screen. The distance the projector must be from the screen is the same as if yo
Summary of the content on the page No. 20
2.INSTALLATION EXAMPLES OF CONNECTIONS. CAUTIONS ON CONNECTIONS: • Unplug the projector and other equipment from the AC • Confirm your connection layout with the user’s manual supply before making connections. accompanying the equipment to be connected with the ISS- • Make sure that the plug of the power cord is properly 6020/ISS-6020G Switcher. connected to the power outlet. A loose connection may cause hum or noise. When Used in Stand Alone Operation Components with RGB and H/V SYNC outputs su
