Summary of the content on the page No. 1
Summary of the content on the page No. 2
FCC Warning Declaration of Conformity Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon This device complies with part 15 of the FCC Rules. Operation is subject to the following 97223-8368 USA two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause We declare under our sole responsibility that this projector conforms to the undesired operation. following direc
Summary of the content on the page No. 3
Table of Contents Introduction 4 Positioning the projector 6 Ceiling Mount 7 Connecting power 8 Connecting a computer source 8 Displaying an image 9 Adjusting the image 10 Connecting a video device 11 Video device connections 11 Shutting down the projector 12 Troubleshooting your setup 12 Using the remote control 20 Using the keypad buttons 22 Using the menus 23 Input menu 24 Picture menu 25 Lamps menu 26 Alignment menu 27 Control menu 28 Service menu 29 Using Projector Web Controls 30 Maintenan
Summary of the content on the page No. 4
• The projector must be installed by a qualified professional in order to ensure Important Operating Considerations for Safety proper operation and reduce the risk of hazards or injury. It is not • Refer to this guide for proper startup and shutdown procedures. recommended you install the projector yourself. • Follow all warnings and cautions in this manual and on the projector. • Refer all service to qualified service personnel. Servicing your own projector • Do not block the lens with any o
Summary of the content on the page No. 5
Optional Accessories Introduction Optional accessories include optional lenses and a ceiling mount. These items and Your new digital projector is simple to connect, easy to use, and straightforward to other accessories can be found on our website at www.infocus.com or at your maintain. It is a versatile projector that is flexible enough to fit almost any local dealer. installation scenario. The IN5552L and IN5852L have XGA 1024 x 768 resolution, the IN5554L and IN5854L have WXGA 1280x800 re
Summary of the content on the page No. 6
Connector Panel HDMI The projector provides both computer and video connection options, including: Wired •HDMI remote RGBHV 12V Screen Trigger •DVI-D SDI DVI-D YPbPr Output • 3G-SDI • BNC RGBHV and YPbPr for RGBHV, EDTV and HDTV • RGB (VGA) computer •S-video • Composite video The projector also provides the following connectors: • LAN port for network control and web server. • 12V screen trigger output •Wired remote jack • RS-232 connector for serial control. Command control codes are in the
Summary of the content on the page No. 7
Positioning the Projector To determine where to position the projector, consider the size and shape of your Vertical Image Offset is -60-% ~ +20% screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines: • Position the projector on a flat surface at a right angle to the screen. The projector (with the standard zoom lens, LENS-074) must be at 55.8”/ 1.42m(XGA) ; 60.2”/1.53m (WXGA) ; 57.2”/1.45m (WUXGA)
Summary of the content on the page No. 8
Ceiling Mount If you wish to install the projector on the ceiling: • The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself. • We strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and installation. Refer to the ceiling mount installation guide for more information. The warranty does not cover any damage caused 10
Summary of the content on the page No. 9
Connecting power Connect power cord Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet. Turn on the power switch. The Power LED on the top of the projector (page 12) turns red. NOTES: Note: Connection to a circuit with a minimum of 20A capacity is recommended. Always use the power cord that shipped with the projector. Connecting a computer source Connect HDMI cable HDMI 1.3 connection Plug an HDMI cable into the video out connector o
Summary of the content on the page No. 10
Displaying an image Press Power button Touch the Power button on the keypad or the remote. The Power button blinks green and the fans start to run. When the lamp turns on, the start up screen will display and the Power button will become solid green. It can take a minute for the image to achieve full brightness. No start up screen? Get help on page 13. Turn on computer or Turn on your computer or video device. video device The image should appear on the projection screen. If it doesn’t, press
Summary of the content on the page No. 11
Adjusting the image Adjust distance Position the projector to the desired distance from the screen at a 90 degree angle to the screen. See the Appendix for screen sizes and distances associated with the various lens options. Adjust zoom, focus and If the image is square but not centered on the screen or viewing area, adjust Zoom lens shift. or Lens Shift using the keypad or remote. Focus can also be adjusted using the keypad or remote. Rotate the elevator feet for adjustment of the projecto
Summary of the content on the page No. 12
the component cable into the adapter and plug the adapter into the RGB Connecting a video device connector. You can connect video devices such as VCRs, DVD players, camcorders, digital Component offers the highest quality analog video output. cameras, video game consoles, HDTV receivers, and TV tuners to the projector. S-video connection Note: This projector does not support audio. You must connect audio directly from If your video device uses a round, four-prong S-video connector, plug an S
Summary of the content on the page No. 13
Shutting down the projector Table 1: Status indicator LED behavior and meaning Auto Power Off The projector has an Auto Power Off feature that automatically turns the projector LED Indicator Meaning off if no active sources are detected and no user interaction with the projector is performed for 20 minutes. By default, this feature is off. Power: Solid red The projector is plugged in. Turning off the projector To turn the projector off, press the Power button on the remote or keypad twice. Bl
Summary of the content on the page No. 14
Problem Solution Result Plug the power cord into the projector, turn No start up screen. Correct image. on the power switch and press the power button. Press the Input button to Computer image projected. Only the start up screen appears. activate the laptop’s external port. Restart laptop 13
Summary of the content on the page No. 15
Problem Solution Result Press the Auto Sync button on the keypad or remote. No computer image, just the words “Signal Computer image projected. To adjust computer refresh rate, go to Control Panel > out of range.” Display > Settings > Advanced > Adapter (location varies by operating system). Signal out of range You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped.” Only my laptop’s background appears, not the Window
Summary of the content on the page No. 16
Problem Solution Result Image fuzzy or cropped Set your computer’s display resolution to the Image clear and not cropped. native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab). A A A For a laptop, disable laptop monitor or turn-on dual- display mode Image not centered on screen. Adjust Lens Shift using the keypad or remote. Correct image. 15
Summary of the content on the page No. 17
Problem Solution Result Image not square. Adjust the angle of the projector, so that it is Square image. square with the screen. Image not sharp. Adjust Sharpness in the Picture menu. Correct image. INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE Picture Mode < High Bright > Contrast < 100 > Brightness < 100 > Adaptive Contrast < Off > Saturation < ------
Summary of the content on the page No. 18
Problem Solution Result Image upside down. Turn Projection Mode to Front in the Alignment Correct image. menu. INPUT PICTURE LAMPS ALIGNMENT CONTROL SERVICE Projection Mode < Front > Fan Mode < Normal > Lens Control Enter A Lens Memory Enter Center Lens Execute Warp Enter Blanking Enter Edge Blend Enter Image reversed left to right. Turn Projection Mod
Summary of the content on the page No. 19
B Problem Solution Result The video embedded in my PowerPoint Turn off the internal LCD display on your laptop. Embedded video plays correctly. presentation does not play on the screen. Lamp won’t turn on and the Temp LED is on. Make sure vents aren’t blocked, turn the Lamp turns on. projector off and allow it to cool for one minute. Temp LED 18
Summary of the content on the page No. 20
Problem Solution Result Lamps turn on. Lamps won’t turn on and the Lamp LEDs are The lamps must be replaced (see page 34). turned on. Lamp Doors Lamp LEDs Replace lamps Still need assistance? If you need assistance, visit our support website at www.infocus.com/support or call us. Check out the How To section for additional information on using this projector for home theater or gaming applications. This product is backed by a limited warranty. An extended warranty plan may be purchased
