Summary of the content on the page No. 1
Owner's Manual
Network Set-up
and Operation
Wired and Wireless Setting
Projector Controller
Network Viewer
Moderator Function
Note; For operating the projector via the Wireless network, USB Wireless
LAN adapter (optionally available) is required.
First, read the owner's manual of the projector to
understand the projector's basic operation and the safety
instructions.
The safety instructions in the owner's manuals should be
followed.
English
Italiano Deutsch Español Français
Summary of the content on the page No. 2
Compliance Federal Communication Commission Notice Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communic
Summary of the content on the page No. 3
Safety Instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION ● EIKI Co., Ltd. assumes no responsibility
Summary of the content on the page No. 4
Table of Contents Compliance............................................................................................2 Safety Instructions................................................................................3 Table of Contents..................................................................................4 Operating Environment and Configuration........................................6 Required Operating Environment for Computers ......................................6 Network Sp
Summary of the content on the page No. 5
Table of Contents Advanced Settings .....................................................................................46 TCP / IP................................................................................................................46 Wireless Setting ..................................................................................................47 E-mail...................................................................................................................48 Admin Passw
Summary of the content on the page No. 6
Operating Environment and Configuration Required Operating Environment for Computers When operating the projector via the networks, computers should meet the operating environment below. Microsoft Windows 98SE/Me or Microsoft Windows 2000 Professional or OS Microsoft Windows XP Home Edition/Professional Pentium III 600MHz or More CPU (more than 2GHz is recommended) 128MB or More Memory 10MB Free HDD Space Required to support any of VGA(640X480), SVGA(800X600), XGA(1024X768), Screen Resolution
Summary of the content on the page No. 7
Operating Environment and Configuration Network Specifications of the Projector LAN Terminal Data communication speed 100Base-TX(100Mbps)/10Base-T(10Mbps) Protocol TCP/IP USB Wireless LAN Adapter (Optionally available. Model : WL-30) Interface Correspond to IEEE8021b/g, USB 2.0 / 1.1 AdHoc, Communication Mode Infrastructure 1/2/5.5/11Mbps(IEEE802.11b) 6/9/12/18/24/36/48/54Mbps(IEEE802.11g) Data Transfer Speed When using AdHoc mode, only IEEE802.11b is usable. Wireless Frequency (Channel) 2412MH
Summary of the content on the page No. 8
8
Summary of the content on the page No. 9
Chapter 1 1. About LAN Functions This chapter describes the features, the mechanism, and connection procedures of the LAN. 9 English
Summary of the content on the page No. 10
1. About LAN Functions LAN Functions and the Features This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation. Accept both Wired and Wireless LAN environment. Wh
Summary of the content on the page No. 11
1. About LAN Functions An Example of the Connection The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . 2.0 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 0.0 2.0 1.5 1.0 0.5 0.0 Computer (2) Computer (1) Access point 11 English
Summary of the content on the page No. 12
1. About LAN Functions LAN Connection Modes Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment. ■ Wireless LAN, Infrastructure Communication Mode Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes. These the communication modes are use
Summary of the content on the page No. 13
1. About LAN Functions ■ Wired LAN Communication Mode Communicate via the LAN line. Computer(1) Computer(2) Computer (3) ✳ Operate the computer mouse with the remote control. When the projector's remote control employs mouse operating function, you can operate the computer by the remote control which is provided with the projector. Use the remote control pointing to the projector. You do not need to connect the USB cable to operate the computer mouse. (For details about the remote control op
Summary of the content on the page No. 14
14
Summary of the content on the page No. 15
Chapter 2 2. Setup Procedures This chapter describes how to install the NetworkModule software and how to set up the networks. 15 English
Summary of the content on the page No. 16
2. Setup Procedures To use the projector via the networks, follow the setup procedures below. Install the software on computers. STEP 1 Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install. Select Wired LAN or Wireless LAN then connect STEP 2 the LAN and set the configuration. Decide depending on the LAN environment. Wired LAN .......Refer to "4. Wired LAN Configurations" (p25-31) Wireless LAN ...Refer to "5. Wireless L
Summary of the content on the page No. 17
2. Setup Procedures Installing the Software Three pieces of software is recorded in the supplied CD-ROM. 1. Insert the CD-ROM into the drive. The software will be activated automatically and "Software License" screen will be displayed. Read the license carefully and if you agree, check "Agree" then click "OK". When the screen is not displayed automatically, open "CD-ROM Drive" in "My computer" of your computer to activate "AutoRun. exe". The software can be displayed both in Japanese and Engl
Summary of the content on the page No. 18
2. Setup Procedures ■ When projecting with the Moderator function. For details about Moderator function, refer to the "8. Use the Moderator Function". a Install "NetworkModule Client" into each client's (participants except for the moderator) computers. For installation, refer to"■ When projecting via a selected computer which is connected to the LAN". (p17) s Click (Select) "NetworkModule Moderator" on the left side of the screen. d Click "Install NetworkModule Moderator". ✳ By clicking the "
Summary of the content on the page No. 19
Chapter 3 3. Names and Functions of the Operation Screen. This chapter describes the functions of each part of the operation screen. 19 English
Summary of the content on the page No. 20
3. Names and Functions of the Operation Screen Network Connection Standby Display Select projector input either "Wired" or "Wireless" and the Network connection standby display will appear. Network environment will be shown on the screen. With this screen, you can confirm that the network connection is whether "Wired" or "Wireless", or network environment of the projector when setting the connection. After selecting "Wired" or "Wireless", "Please wait..." message will appear and then change
